Abstract:The purpose of this work is to calculate the shear pressure gradient and shear radius of paraffinic oil in a stopped pipeline as functions of the longitudinal coordinate z along the axis of the stopped section, as well as the minimum shear pressure difference between the ends of the pipeline, taking into account the non-uniform cooling of oil over time in the radial direction, leading to a significant increase in static shear stress with distance from the center to the edge of the pipe. Using a simple mathematical model that describes the non-uniform cooling of oil along the radius r and along the longitudinal coordinate z along the pipe axis due to heat conduction, it is shown that with a smooth increase in start-up pressure at the beginning of a stopped pipeline section, the cooling oil can shift not along the pipe wall, but along its central part, the radius of which depends both on the oil cooling time and on the z coordinate along the pipeline axis. Calculations show that the process of cooling of the stopped oil can be conditionally divided into three stages. At the first time stage of cooling, the oil near the pipeline axis does not cool down to the temperature of the appearance of static shear stress, that is, it is actually Newtonian and there is no problem with starting this oil layer. At the third time stage of cooling, when the oil cools below the temperature of the onset of paraffin mass crystallization, that is, it turns into a viscous-plastic one in the entire volume of the oil pipeline, the calculation of the minimum pressure difference between the ends of the pipe required to start the oil pipeline can be carried out using a method that qualitatively coincides with the method described in [27]. Finally, in the second cooling time step, which occupies an intermediate position between the first and third steps, the pipeline can be divided into two sections in the longitudinal direction. The behavior of oil in the first section, adjacent to the beginning of the pipeline, resembles the behavior of oil in the entire pipeline at the end of the first stage of cooling, and in the second section, extending from the end of the first section to the end of the pipe, the oil behaves similarly to the oil in the entire pipeline in the third temporary stage of cooling. In this case, the boundary between the first and second sections of the pipe during the second temporary stage of cooling is displaced from the end of the pipeline to its beginning. It is shown that calculations of the shear pressure required to resume the pumping of cooled oil, which do not take into account the inhomogeneous cooling of oil in the pipe cross section, can overestimate the desired pressure value. This fact should be taken into account in practice when assessing the restart pressure and the safe shutdown time of a pipeline transporting highly pourable oils using the “hot” pumping method. All laboratory measurements of the thermal parameters of oil, as well as calculations of pressure and shear radius, were carried out on the example of the Usa-Ukhta main oil pipeline of JSC Transneft-North.

Analysis of restart-up pressure drop characteristics of heavy oil-water ring transportation pipeline

Predictive Model of Restart-Up Pressure Drop after Shutdown for Heavy Oil–Water Ring Transportation Pipeline

Experimental investigation on the restart characterization of shale oil-water flow in a horizontal pipe

Rheological Behavior of Heavy Crude Oil and Its Emulsions

Analysis of influence factors of start-up yield stress for heavy oil emulsions

Study on the Flow Characteristics of Heavy Oil-Water Two-Phase Flow in the Horizontal Pipeline

Cross-dimensional isothermal model for the transient restart of weakly compressible laminar/turbulent flow of time-dependent non-Newtonian fluid in a long pipeline

Experimental investigation on flow patterns and pressure gradients of shale oil-water flow in a horizontal pipe

Oil–Water Hydrodynamics Model during Oil Displacement by Water in Down-Hill Mobile Pipeline

Study on the Pressure Drop Variation and Prediction Model of Heavy Oil Gas-Liquid Two-Phase Flow

Computational Fluid Dynamics Simulation of Oil-Water Batch Transport in a Pumpless Virtual Flow Loop

A pressure drop model of post-fracturing shut-in considering the effect of fracturing-fluid imbibition and oil replacement

THE INFLUENCE OF INHOMOGENEOUS RADIAL PROFILE OF WAXY CRUDE OIL TEMPERATURE AND SHEAR STRESS IN A STOPPED PIPELINE ON THE RESTART PUMPING PRESSURE FOR «USA — UKHTA» MAIN PIPELINE

Investigation on Flow Patterns and Pressure Drops of Highly Viscous Crude Oil–water Flows in a Horizontal Pipe

Study on the Hydrodynamic Performance and Stability Characteristics of Oil-Water Annular Flow Through a 90° Elbow Pipe

Heat transfer characteristics of oil-water two-phase in pipeline transportation during shutdown

Reservoir recovery study with stability analysis model constructed by water-driven oil flat sand filling experiment: example of well area X in Tankou oilfield, China

Investigation on Method of Water Holdup Prediction for Oil-Water Flow in Vertical Pipes

Research on heat transfer characteristics of long-distance pipeline under shutdown and maintenance conditions

Experimental investigation of oil–water flow in the horizontal and vertical sections of a continuous transportation pipe

Model and Analysis of Pump-Stopping Pressure Drop with Consideration of Hydraulic Fracture Network in Tight Oil Reservoirs