Abstract:The combined finite-discrete element method (FDEM) has been widely used in the numerical study of rock mechanics and geotechnical engineering. Selection of the correct parameter values is a prerequisite to ensure the accuracy of the simulation results. However, current calibration procedures are relatively cumbersome, and the parameters are strongly dependent on the element size. To eliminate the dependence of parameter values on the element size, this paper proposes a new constitutive model based on the stress-strain relationship. In addition, uniaxial compression and direct tension simulations are used to investigate the sensitivities of type II and type I fracture energies, i.e., GII and GI, including the influence of the GI (or GII) value on the simulation results of direct tension (or uniaxial compression) and the influence of different parameters (such as Young's modulus E, Poisson's ratio ν, cohesion c, internal friction angle φi, tensile strength ft and element size h) on the selection of the values of GII and GI. The following results are obtained. <a class="workspace-trigger" href="#e0005">(1)</a> As GI or GII increases, the strength of the rock sample increases, and the plastic characteristics are more obvious, but the failure mode tends to be stable. <a class="workspace-trigger" href="#e0010">(2)</a> As the E value increases, the value of GI or GII decreases as a power function. As the value of ft or c increases, the value of GI or GII increases as a power function. However, other parameters, including ν, φi and h, have no effect on the selection of the values of GII and GI. <a class="workspace-trigger" href="#e0015">(3)</a> Actual uniaxial compression and triaxial compression simulations prove that the calibrated GII and GI values are reasonable. In this study, only two fracture energies, GII and GI, must be calibrated; other macroparameters can be obtained through laboratory tests, and other microparameters can be obtained from previous empirical or theoretical values, which greatly improves the calibration efficiency of FDEM input parameters.

The Calibration of Microscopic Parameters for the 3D Finite-Discrete Element Method

Systematical Calibration and Validation of Discrete Element Models for Fiber Reinforced Cement Treated Aggregates

Local Calibration of a Weak Stiffness On-Machine Measuring Device with a New 3-D Calibrator

Research on Finite Element Calibration Technology of Calibration Coefficients in Hole-drilling Method

Microparameters Calibration for Discrete Element Method Based on Gaussian Processes Response Surface Methodology

Calibration of the microparameters of the discrete element method using a relevance vector machine and its application to rockfill materials

An iterative method to improve the calibration accuracy of flat-joint models: Catch-up penalty algorithm

Experimental Simulation and a Reliable Calibration Method of Rockfill Microscopic Parameters by Considering Flexible Boundary

Sensitivity analysis of fracture energies for the combined finite-discrete element method (FDEM)

Calibrating the Micromechanical Parameters of the PFC2D(3D) Models Using the Improved Simulated Annealing Algorithm

A calibration framework for DEM models based on the stress‒strain curve of uniaxial compressive tests by using the AEO algorithm and several calibration suggestions

Numerical calibration for fracture parameters of three-point bending semi-circular specimens

Calibration of the Discrete Element Method and Modeling of Shortening Experiments

Measurement and Simulation Validation of DEM Parameters of Pellet, Sinter and Coke Particles

A Study of Three Intrinsic Problems of the Classic Discrete Element Method Using Flat-Joint Model

Research on calibration method of microscopic parameters of siltstone based on gray theory

Integration of Finite Element Analysis and Laboratory Analysis on 3D Models for Methodology Calibration

Meso-parameters Calibration of Rock Specimens Based on Flat-Joint Contact Model

A Three-Dimensional Discrete Element Model of Triaxial Tests Based on a New Flexible Membrane Boundary

Study on the correlation and calibration of macro and micro parameters of discrete element model for sandstone

A DEM parameters calibration method for three-dimensional model of the lunar rock based on the approximate model