Abstract:<p>The aim of the present paper is to evaluate the effect of Lode angle incorporation into a fracture criterion when predicting the ballistic resistance of 2024-T351 aluminum alloy plates struck by cylindrical projectiles with different nose shapes through finite element (FE) simulations. To this end ballistic tests in the sub-ordnance impact velocity range were firstly conducted on 9.94 mm thick 2024-T351 aluminum alloy plates using cylindrical projectiles with blunt, hemispherical and ogival nose shapes, a nominal diameter of 12.66 mm, and a nominal mass of 50 g. Ballistic limit velocities (BLVs) for different projectile-target pairs considered were calculated using initial vs. residual velocity data obtained in the experiments. Subsequently FE simulations of the conducted experiments were performed with SIMULIA Abaqus software. In those simulations Johnson-Cook yield criterion with a modified strain hardening law was accompanied with either the Lode-independent Johnson-Cook (JC) fracture criterion or the Lode-dependent modified Mohr-Coulomb (MMC) fracture criterion to describe target material properties. Finally, the predicted ballistic resistance and fracture patterns of the targets were compared with those observed in the experiments. It was found that in the simulations with the Lode-independent JC fracture criterion the BLVs of the targets were overestimated by 18.0-35.1% depending on the projectile nose shape. In the simulations with MMC fracture criterion the BLVs predictions were substantially improved, so that the difference with the experimental results did not exceed 9.0%. Targets failure mechanisms obtained in the simulations with MMC fracture criterion also better match the experiments than those predicted with JC fracture criterion. In the simulations with MMC fracture criterion the targets impacted by the projectiles with blunt and hemispherical noses failed through shear plugging, whereas ogive-nosed projectiles caused ductile hole enlargement and target fragmentation due to its rear side radial fracture and bending of formed short petals with their eventual shear fracture. At the same time the simulations with JC fracture criterion predicted shear plugging for the blunt-nosed projectiles, very small conical plug ejection and target fragmentation due to discing for the hemispherical-nosed projectiles, and ductile hole enlargement for the ogive-nosed projectiles. A detailed analysis of the failure process revealed that in the case of the ogive-nosed and hemispherical-nosed projectiles, respectively, the ductile hole enlargement occurs during the initial stage of the impact and subsequent through-thickness fracture develops causing either fragmentation of the target or its shear plugging failure. The Lode-independent JC fracture criterion overestimates a material fracture strain under shear, thus leading to poor prediction of 2024-T351 aluminum alloy targets ballistic performance in the numerical simulations.</p>

Ballistic Characteristics on Oblique Penetrating Multi-Layer Aluminium Targets by Annular Groove Projectile

Numerical Study on the Perforation of Steel Plates by Multiple Projectiles

Simulation of ballistic performance of a two-layered structure of nanostructured metal and ceramic

Trajectory prediction of rigid projectile for oblique penetration into multi-layer aluminum targets

Strain-rate-dependent Cohesive Zone Modelling of Charge Damage Behavior when a Projectile Penetrates Multilayered Targets

Numerical simulation of the disk fragment impacting resistance of plate target

The Effect of Material Layering Order on the Ballistic Performances of Targets Against the Impact of Ogival-Nosed Projectiles

Research on Oblique Penetration of Projectiles into Targets of Different Materials

Oblique Penetration of Spherical Projectile into Low-Carbon Steel Target: Experiment, Theory, 3D Penetration Model

Analytical and experimental study on elliptical cross-section double-ogive-nose projectile penetration into plain concrete target

On Ballistic Performance of a Metal Target with Crescent-Shaped Cavity Structure

Theoretical Investigation on Failure Behavior of Ogive-Nose Projectile Subjected to Impact Loading

Experimental investigation on the ballistic resistance of monolithic and multi-layered plates against hemispherical-nosed projectiles impact

Oblique penetration law of short-rod projectile into thin metal target

Experimental investigation on the ballistic performance of double-layered plates subjected to impact by projectile of high strength

Ballistic performance of Q235 metal plates subjected to impact by blunt-nosed projectiles

Influence of the Movement of Cylindrical Target Plate on the Penetrating Ability of Kinetic Energy Projectile

Experimental and Numerical Study on the Ballistic Resistance of Heterogeneous Double-Layered Aluminum Alloy Targets Against Blunt Projectiles

Experimental and numerical study on the ballistic resistance of 6061-T651 aluminum alloy thin plates struck by different nose shapes of projectiles

NUMERICAL SIMULATION FOR THE EFFECT OF BROADSIDE STRUCTURE ON RESISTING TRUNCATED-OGIVE NOSE PROJECTILE PENETRATION

Effect of Lode angle incorporation into a fracture criterion in predicting the ballistic resistance of 2024-T351 aluminum alloy plates struck by cylindrical projectiles with different nose shapes