Abstract:<h3 class="u-h4 u-margin-m-top u-margin-xs-bottom">Background</h3><p>/Objective: In recent years, prostheses have been widely used for limb reconstruction after pelvic tumour resection. However, prostheses are associated with problems leading to tumour recurrence, poor implant matching, defects after tumour resection, and easy implant looseness or failure. To achieve a precise preoperative design, complete tumour resection, and better anatomical structure matching and prosthesis stability, this study used three-dimensionally (3D)-printed osteotomy guides and personalised prostheses for reconstruction after pelvic tumour resection. This study aimed to explore the early clinical efficacy of 3D printed personalised prostheses for the reconstruction of bone defects after pelvic tumour resection.</p><h3 class="u-h4 u-margin-m-top u-margin-xs-bottom">Methods</h3><p>A total of 20 patients (12 males, 8 females) with pelvic tumours surgically treated at our hospital between October 2014 and October 2019 were selected. There were 10 cases each of giant cell bone tumours and osteochondrosarcomas. According to Enneking zoning, there were 11 and 9 cases with tumours located in zones I and II, respectively. All cases were equally divided into conventional and 3D printing groups. For repair and reconstruction, a nail rod system or a steel plate was used in the conventional group while individualised 3D-printed prostheses were used in the 3D printing group. The surgical incision, duration of surgery, intraoperative blood loss, and the negative rate of resection margins in postoperative tumour specimens were examined. The follow-up focused on tumour recurrence, complications, and the Musculoskeletal Tumor Society (MSTS) score.</p><h3 class="u-h4 u-margin-m-top u-margin-xs-bottom">Results</h3><p>All cases were followed-up for 6–24 months. The average incision length, duration of surgery, amount of intraoperative blood loss, and MSTS score of the 3D printing group were 10.0 ± 3.1 cm, 115.2 ± 25.3 min, 213.2 ± 104.6 mL, 23.8 ± 1.3, respectively, and those of the conventional group were 19.8 ± 8.4 cm, 156.8 ± 61.4 min, 361.4 ± 164.2 mL, and 18.3 ± 1.4, respectively. Histological tumour specimen examination showed nine and three cases with negative resection margins in the 3D printing group and the conventional group, respectively. The abovementioned indicators were significantly different between both groups (<em>P</em> < 0.05).</p><h3 class="u-h4 u-margin-m-top u-margin-xs-bottom">Conclusion</h3><p>Applying 3D printed surgical guides and personalised prostheses for pelvic tumour resection, repair, and reconstruction, as well as preoperative planning and design, enables more accurate tumour resections and better prosthesis-patient matchings, possibly reducing surgical trauma, shortening the duration of surgery, and promoting the functional recovery of patients postoperatively.</p><h3 class="u-h4 u-margin-m-top u-margin-xs-bottom">The Translation Potential of this Article</h3><p>Contrary to existing studies on 3D printed personalised prostheses, this study reports the clinical efficacy of the aforementioned technology in treating bone defects in a series of patients who underwent pelvic tumour resection. Moreover, it presents a comprehensive comparison of this technology with conventional procedures, thus strengthening its importance in treatment regimens for reconstructing bone defects.</p>

Outcomes Following the Excision of Sarcoma and Chest Wall Reconstruction Using 3D Printed Implant

Three-dimensional printed titanium chest wall reconstruction for tumor removal in the sternal region

The application of three‐dimensional custom‐made prostheses in chest wall reconstruction after oncologic sternal resection

Three-dimensional printing PEEK implant: a novel choice for the reconstruction of chest wall defect.

Surgical Planning By Three Dimensional Printing For Huge Chondrosarcoma Of Chest Wall Resection

Extended Radical Resection and Chest Wall Reconstruction for a Pulmonary Sarcomatoid Carcinoma: a Case Report

Impact of three-dimensional-printing technology guidance on surgical outcomes for retroperitoneal sarcoma: A propensity score-matched study

Three-Dimensional Printing-Based Personalized Limb Salvage And Reconstruction Treatment Of Pelvic Tumors

Clinical exploration of the international society of limb salvage classification of endoprosthetic failure using Henderson in the application of 3D-printed pelvic tumor prostheses

A 3D-printed patient-specific modular implants for pelvic reconstruction of bone tumors involving the sacroiliac joint

An innovative reconstruction of an enbloc resected composite giant chest and abdominal wall chondrosarcoma with 3D-composite mesh

Primary Chest Wall Ewing Sarcoma: Treatment and Long-Term Results

Efficacy of 3D-printed segmental tumor prosthesis for reconstruction of bone defects after resection of weight-bearing long bone tumors in the lower extremity

3D Printing Technology for Chest Wall Reconstruction With a Sternum-Ribs-Cartilage Titanium Implant: From Ideation to Creation

Design, additive manufacture and clinical application of a patient-specific titanium implant to anatomically reconstruct a large chest wall defect

Clinical study of 3D printed personalized prosthesis in the treatment of bone defect after pelvic tumor resection

Upper cervical spine reconstruction using customized 3D-printed vertebral body in 9 patients with primary tumors involving C2

Reconstruction of the Upper Cervical Spine Using a Personalized 3D-Printed Vertebral Body in an Adolescent with Ewing Sarcoma.

3D-Printed Patient-Customized Artificial Vertebral Body for Spinal Reconstruction after Total En Bloc Spondylectomy of Complex Multi-Level Spinal Tumors

A Novel 3D-Printed Scaffold for Patient-Specific Partial Breast Reconstruction: A Prospective, Single-Arm Clinical Trial.

Surgical Resection of Giant Chest Wall Chondrosarcoma Combined with Sandwich Chest Wall Reconstruction in One Case