Abstract:Sintering process is an important part of the specimen preparation process, which directly affects the properties of materials. In order to obtain the best sintering control factors of Al-rich PTFE/Al/TiH2 active materials, Al-rich PTFE/Al/TiH2 active specimens with different sintering control factors were prepared using a mold pressing sintering method. A quasi-static compression experiment was carried out on a universal material testing machine, and a real stress-strain curve was obtained. The effects of sintering control factors on the properties of Al-rich PTFE/Al/TiH2 active materials were analyzed by means of mechanical parameters such as compressive strength, failure strain and toughness. SEM and XRD were used to analyze the microstructure and phase of the sintered samples. The results show that: (1) With the increase of cooling rate, the density, yield strength, strain hardening modulus, compressive strength and toughness of Al-rich Al/PTFE/TiH2 specimens decrease gradually, while the failure strain and pores of the specimens increase gradually. (2) With the increase of sintering temperature, the density, maximum true strain and toughness of the specimens first increase and then decrease, and the failure strain of the specimens gradually increases. When the sintering temperature is 360 °C, the PTFE matrix and particles inside the specimen are closely combined, a small number of particles are exposed on the PTFE matrix and there are a small number of voids. (3) With the increase of holding time at 360 °C, the strength and toughness of the material first decrease and then increase. When the holding time is 6 h, the interface between particles and matrix inside the specimen is the strongest, and the crack propagation inside the specimen is less. (4) When the sintering time increased from 1 h to 4 h at 315 °C, the compressive strength of the specimen increased by 1.62%, the toughness of the specimen decreased by 0.55% and the failure strain of the specimen decreased by 0.54%. The interface between PTFE matrix and particles is the strongest and the crack propagation is less in the specimen with a holding time of 4 h. (5) Above all, the optimum sintering parameters of Al-rich Al/PTFE/TiH2 materials are cooling rate of 25 °C/h, sintering temperature of 360 °C, holding time of 6 h and holding time of 4 h at 315 °C. (6) The reactivity of Al-rich Al/PTFE/TiH2 specimens with 10% content of TiH2 under static compression is not significantly affected by sintering parameters.

Dynamic Response Behavior of PTFE/Al/oxide Reactive Materials

Research on the Impact Initiation Behavior of PTFE/Al/Ni2O3 Reactive Materials.

Impact Energy Release Characteristics of PTFE/Al/CuO Reactive Materials Measured by a New Energy Release Testing Device

Investigation on the microstructures, mechanical properties and impact initiation characteristics of Al/PTFE reactive materials reinforced by TiH 2 particles

The effect of temperature-induced phase transition of PTFE on the dynamic mechanical behavior and impact-induced initiation characteristics of Al/PTFE

Mechanical Behavior of Polytetrafluoroethylene/Aluminum Energetic Materials under High and Low Temperature Conditions

Effects of Al Particle Size on the Impact Energy Release of Al-Rich PTFE/Al Composites under Different Strain Rates

Controlling Shock-Induced Energy Release Characteristics of PTFE/Al by Adding Oxides

Effects of three types of additives on mechanical properties and impact energy release characteristics of Al/PTFE reactive structural material

Shock-induced chemical reaction characteristics of PTFE-Al-Bi2O3 reactive materials

The influence of metallic particle size on the mechanical properties of PTFE-Al-W powder composites

Zhu‐Wang‐Tang constitutive model of reinforced Al/PTFE materials at medium strain rate

An approach to distinguish chemical and kinetic energy of reactive materials: PTFE/LiF as an inert substitute to PTFE/Al

Energy Release Characteristics and Reaction Mechanism of PTFE/Al/Bi2O3 Reactive Materials under Drop-Hammer Test

High Strain and Strain-Rate Behaviour of PTFE/Aluminium/Tungsten Mixtures

Dynamic Constitutive Model of Tungsten‐Whisker‐Reinforced Aluminum/Polytetrafluoroethylene Composite Material and Quantitative Determination of Impact Reaction Release Energy in Vacuum Environment

The effect of al particle size on thermal decomposition, mechanical strength and sensitivity of Al/ZrH2/PTFE composite

Effect of Sintering Factors on Properties of Al-Rich PTFE/Al/TiH2 Active Materials

Dynamic constitutive model and ignition behavior of enhanced Al/PTFE

The dynamic mechanical response of Al2O3 and TiB2 particulate reinforced aluminum matrix composites produced by in-situ reaction

Dynamic compression-shear ignition mechanism of Al/PTFE reactive materials