Abstract:The nickel(Ni)-patterned electrode enables researchers to quantify the triple-phase boundary (TPB) length and Ni surface area, exclude the influence of bulk gas diffusion and clearly separate the active regions of the chemical/electrochemical reactions. This tool has been studied for identifying the reaction mechanism in SOFC but rarely in SOEC. In this study, the Ni-patterned electrodes with the stripe width of 100 μm were tested in both the solid oxide fuel cell (SOFC) and solid oxide electrolysis cell (SOEC) modes at the atmosphere of H2O/H2 and further H2O/CO2/H2/CO. The experimental test shows the stability of the Ni-patterned electrode in the H2O/H2 atmosphere was much poorer than that in the CO/CO2 atmosphere due to the nickel reacting with steam. Thus, the Ni-patterned electrode needed to operate at a temperature of ≤700oC with the inlet H2/H2O molar ratio of >7 and the current-applied time shouldn’t be over 5 h to keep the accuracy of the TPB length and Ni surface area. The effects of the temperature, partial pressure of H2O and H2 are investigated. The activation energy of the Ni-patterned electrodes was 0.386 eV. The electrochemical performance had a positive correlation with both the partial pressure of H2 and H2O, especially showed higher sensitivity to the partial pressure of H2O. Further, a possible mechanism of the H2O/H2 electrochemical conversion was proposed according to the experimental data and existing literature, which contains two-step charge-transfer reaction: H(Ni)+O2-(YSZ)OH-(YSZ)+(Ni)+e- and H(Ni)+OH-(YSZ)H2O(YSZ)+(Ni)+e-. Based on the experiments, an analytical calculation was performed to investigate the rate-determining steps in the Ni-patterned electrodes by bridging the connection between the kinetic parameters and operating conditions. The results indicate the rate-limiting steps may be different for the SOFC and SOEC modes. In SOFC mode, the H2 electrochemical oxidation could depend more on the charge-transfer reaction H(Ni)+O2-(YSZ)→OH-(YSZ)+(Ni)+e-, however in SOEC mode, the rate-determining step of the H2O electrochemical reduction should be H2O(YSZ)+(Ni)+e-→OH-(YSZ)+H(Ni). In this way, a reversible mechanism could be applied for reversible SOFC (RSOFC) to describe the conversion between hydrogen and steam by different charge-transfer-reaction domination in the SOFC and SOEC mode. Figure 1

A Comparative Study of the Performance and Electrode Processes of Solid Oxide H<sub>2</sub>O Electrolysis and CO<sub>2</sub> Electrolysis

A Comparative Study of the Performance and Electrode Processes of Solid Oxide H<sub>2</sub>O Electrolysis and CO<sub>2</sub> Electrolysis

Dynamic Behavior of High-Temperature CO2/H2O Co-Electrolysis Coupled with Real Fluctuating Renewable Power

Different Performance and Mechanisms of CO2 Electrolysis with CO and H2 As Protective Gases in Solid Oxide Electrolysis Cell

Electrochemical Characterization and Mechanism Analysis of High Temperature Co-electrolysis of CO2 and H2O in a Solid Oxide Electrolysis Cell

Investigation on the reaction mechanism of solid oxide co-electrolysis with different inlet mixtures based on the comparison of CO2 electrolysis and H2O electrolysis

Performance and Methane Production Characteristics of H2O–CO2 Co-Electrolysis in Solid Oxide Electrolysis Cells

Comparison of a solid oxide cell with nickel/gadolinium‐doped ceria fuel electrode during operation with hydrogen/steam and carbon monoxide/carbon dioxide

Reaction Mechanism and Rate-Determining Step Speculation of Reversible CO/CO2 Electrochemical Conversion on the Nickel Patterned Electrodes

Electrochemical characterization of electrolyte supported solid oxide electrolysis cell during CO2/H2O co-electrolysis

Effect of seawater on the performance of flat-tube solid oxide cell for CO2/H2O co-electrolysis

Carbon Monoxide/carbon Dioxide Electrochemical Conversion on Patterned Nickel Electrodes Operating in Fuel Cell and Electrolysis Cell Modes

Understanding the Occurrence of the Individual CO2 Electrolysis During H2O-CO2 Co-Electrolysis in Classic Planar Ni-YSZ/YSZ/LSM-YSZ Solid Oxide Cells

La0.8Sr0.2Co0.8Ni0.2O3-δ Impregnated Oxygen Electrode for H2O/CO2 Co-Electrolysis in Solid Oxide Electrolysis Cells

Performance Evolution Analysis of a Solid Oxide Cell Operated in Fuel-Cell, Electrolysis and Cycle Modes

Electrolysis of H 2O and CO 2 in an oxygen-ion conducting solid oxide electrolyzer with a La 0.2Sr 0.8TiO 3+δ composite cathode

Mechanism for Reversible CO/CO2 Electrochemical Conversion on a Patterned Nickel Electrode

Physical principles for the calculation of equilibrium potential for co-electrolysis of steam and carbon dioxide in a Solid Oxide Electrolyzer Cell (SOEC)

Experiments and Modeling of Solid Oxide Co-Electrolysis: Occurrence of CO2 Electrolysis and Safe Operating Conditions

Comparative Performance Investigation of Different Gas Flow Configurations for a Planar Solid Oxide Electrolyzer Cell

Elementary Reaction Modeling of Co2/H2o Co-Electrolysis Cell Considering Effects of Cathode Thickness