Abstract:Metal bipolar plates (BPPs) are crucial components of proton exchange membrane fuel cells (PEMFCs), with the quality of their formation affects the power generation efficiency and lifespan of the fuel cells. The predominant manufacturing method, stamping, often results in localized excessive stretching of metal BPPs, thereby limiting the depth of the flow channels. Roll forming, dominated by bending deformation, is a forming process that ensures uniform thinning and greater depth of BPPs. The multi-directional flow channel roll forming model for BPPs is constructed in this paper for the first time, the characteristics of the roll forming process is investigated. Effects of process parameters on the forming results are discussed. The investigation indicates that during the roll forming process, the channel ports and corners are critical areas where defects are most likely to occur. The average filling ratio of the longitudinal flow channels is 5.6% higher than that of the transverse flow channels. The plastic strain in the longitudinal flow channels is about 36% higher than in the transverse ones, which making the form is more difficult to form, but the thickness is more uniform. Increasing the diameter of the rollers can enhance the filling ratio and flatness, but it will exacerbate thinning at the corners of the flow channels. When the ratio of the flow channel width to the rib width is close to 1, the filling ratio of the BPP is higher, with less thinning, resulting in a better forming result. As the depth of the flow channel increases, resulting in a thinner BPP, when depth-to-width ratio exceeding 0.6 is more likely to lead to failure. Increasing the speed of roll forming can lead to a greater thinning of the BPP and may even cause it to crack. The thinner the sheet metal is, the higher the filling ratio of the BPP and the more uniform its thickness. Those results can provide technical references for the structural design and forming process optimization of BPPs.

Sensitivity Analysis and Robust Design of the Forming Process Parameters of the Metallic Bipolar Plate for Proton Exchange Membrane Fuel Cells

Robust Design for the Precision Forming of Metallic Bipolar Plates of Proton Exchange Membrane Fuel Cell

Fabrication of Metallic Bipolar Plates for Proton Exchange Membrane Fuel Cell by Flexible Forming Process-Numerical Simulations and Experiments

Design, Optimization, and Fabrication of Slotted-Interdigitated Thin Metallic Bipolar Plates for PEM Fuel Cells

Flow Channel Design for Metallic Bipolar Plates in Proton Exchange Membrane Fuel Cells: Experiments

Dimensional tolerance analysis of proton exchange membrane fuel cells with metallic bipolar plates

Thin Metallic Wave-Like Channel Bipolar Plates for Proton Exchange Membrane Fuel Cells: Deformation Behavior, Formability Analysis and Process Design

Investigation and optimization of the ultra-thin metallic bipolar plate multi-stage forming for proton exchange membrane fuel cell

Study on Shape Error Effect of Metallic Bipolar Plate on the GDL Contact Pressure Distribution in Proton Exchange Membrane Fuel Cell

Contact Resistance Prediction of Proton Exchange Membrane Fuel Cell Considering Fabrication Characteristics of Metallic Bipolar Plates

Investigation of roll forming process and quality control factors for metal bipolar plates

Formability and Flow Channel Design for Thin Metallic Bipolar Plates in PEM Fuel Cells: Modeling

Flow channel shape optimum design for hydroformed metal bipolar plate in PEM fuel cell

Plastic Deformation Forming of Metallic Bi-Polar Plate – Part 1: Theoretical Basis and Fundamental

Design and manufacturing of stainless steel bipolar plates for proton exchange membrane fuel cells

A novel ex-situ accelerated evaluation method for metallic bipolar plates in proton exchange membrane fuel cells

Modeling, design, materials and fabrication of bipolar plates for proton exchange membrane fuel cell: A review

Mechanical Degradation of Proton Exchange Membrane During Assembly and Running Processes in Proton Exchange Membrane Fuel Cells with Metallic Bipolar Plates

Research on Design and Optimization of Large Metal Bipolar Plate Sealing for Proton Exchange Membrane Fuel Cells

Numerical Investigation of Formed Residual Stresses and the Thickness of Stainless Steel Bipolar Plate in PEMFC

A comparative analysis of predictive models for estimating the formability of stamped titanium bipolar plates for proton exchange membrane fuel cells