Abstract:Most additive manufacturing (AM) technologies use heat to fuse materials together to create the manufactured part. The heat used in the AM process distorts the parts. Powder bed–based 3D printers can print multiple parts in their build chamber. The distortion is not uniform across the different locations of the build volume. Parts printed in different locations will have different thermal histories and therefore different distortions. In some cases, the achievable accuracy of the parts is insufficient due to the distortion. Subtractive processes such as milling, turning, and grinding make it difficult or impossible to improve part accuracy. For AM to produce more accurate parts, a distortion reduction method must be implemented. To take advantage of the ability to print multiple parts in a powder-based polymer 3D printing process in one build unit, a distortion mitigation technique must be applied to all the parts being printed simultaneously in the build chamber. The performance of the distortion mitigation method can be evaluated by measuring the dimensional accuracy of the uncompensated and compensated parts. Uncompensated 3D printing uses the nominal 3D model, which is the normal use of the 3D printers. Compensated 3D printing uses a distorted 3D model that is used for the printing. The 3D model is compensated with the reversed distortion data obtained from uncompensated manufacturing. X-ray computed tomography (XCT) is the chosen measurement method to extract the point cloud for the dimensional measurements. Unlike optical 3D scanners and coordinate measuring machines (CMM), the XCT is able to measure undercut and internal surfaces. The nominal difference % is improved by 18% by using compensation for the 3D models in the case of distances between two parallel planes. The standard deviation of the measured values was also improved. The distortion reduction method studied can significantly reduce the calibration errors of the 3D printer build chamber. When the tolerances of the parts are close to the limit of the 3D printer, this method can reduce the number of rejected parts. The XCT measurement of the parts is costly, so this method can be cost effective for high value parts or large production volumes.

Study about the Warping Distortion of Selective Laser Sintering Rapid Prototyping Workpiece

Study of Biomass Composite Workpiece Support Structure Based on Selective Laser Sintering Technology

An experimental and modeling study on warping in additively manufactured overhang structures

Influence of different Processing Parameter on distortion and Residual Stress of Inconel 718 Alloys Fabricated by Selective Laser Melting (SLM)

Effect of Process Parameters on Residual Stresses, Distortions, and Porosity in Selective Laser Melting of Maraging Steel 300

Study of thermal stress deformation in hybrid 3D printing and milling process of PEEK material

The Study of Selective Laser Sintering Technology of Stainless Steel Powder

Effect of Process Parameters on Distortions Based on the Quantitative Model in the SLM Process

A novel experimental method for in situ strain measurement during selective laser melting

Finite Element Analysis of Warping and Mechanical Properties of 3D Parts Printed by Fused Deposition Modeling

Experimental study on parameters optimization of selective laser melting 316L stainless steel based on response surface methodology

Investigation of the accuracy and roughness in the laser powder bed fusion process

Process Study of Selective Laser Sintering of PS/GF/HGM Composites

Experimental Study on Warpage Phenomenon of Wax Parts Manufactured by Fused Filament Fabrication

Effects of Selective Laser Melting Process Parameters on the Accuracy of the Intaglio Surface of Maxillary Removable Partial Denture Frameworks

Research on the Fused Deposition Modeling of Polyether Ether Ketone

The effect of rescanning strategy on residual stress and deformation of laser-based powder bed fusion of 316L stainless steel thin-walled parts

An Experimental Investigation into Residual Stress Control of 24CrNiMo Alloy Steel by Selective Laser Melting

Study on warpage deformation of micro extrusion 3D Printing Bone Tissue Engineering Scaffold and Its Optimization Method

Optimal Design of Support Structures in Selective Laser Melting of Parts

Computed tomography as distortion mitigation method for selective laser sintering mass production