Abstract:Narrow-band response photodetectors are widely used in situations where specific light wavelengths need to be detected, such as communication. imaging, surveillance, etc. These detectors require not only the narrowest spectral response window, but also the highest external quantum efficiency (EQE) within the response window. Generally, the semiconductor photoactive layer in the photodetector will absorb the photons with energy greater than the band gap, and the spectral response window is usually wide, so it needs to combine with the filter of specific wavelength to achieve narrow band response. However, the introduction of filters, in addition to the increased cost, will inevitably lead to additional light reflection losses, which will significantly reduce EQE. When the film thickness of the heterojunction is up to inn, the narrow-band response near the band edge can be achieved without a filter. However, the problem brought by thick film is that the photocurrent also decreases, resulting in lower EQE (<30%) of the device. Although higher reverse bias increases the photocurrent and EQE, it also increases the collection probability of short-wave photogenerated carriers, thus damaging the narrow-band response. By greatly reducing the proportion of organic receptors and donors in the micron-size photoactive layer, the narrow-band response window of ca. 650 mu was achieved, and the EQE was up to ca. 53500% under -60 V reverse bias. This kind of organic photodetector achieving the photomultiplication mainly attributes to the trapped charges at the photoactive layer/electrode interface which will capture the photogenerated electrons (holes), and when the photogenerated electrons (holes) are collected, the electric neutral balance in the photoactive layer is broken. The trapped photogenerated electrons (holes) at the interface will cause the change of interface potential energy, which induces the interface band bending of the photoactive layer, and promotes the metal electrode to inject holes into the photoactive layer to maintain the neutral balance. Because the injection current is much higher than the photoelectric current, the superposition of the two can significantly increase EQE and even produce gain. However, the idea of obtaining higher EQE by further increasing the concentration of interfacial trapped electrons is difficult to be realized by increasing the proportion of receptors, which not only reduces EQE, but also increases the full width at half maximum (FWHM) of the response window and destroys the narrow-band response. In this work, the structure of ITO/poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT)/poly(3-hexylthiophene) (P3HT)/[6,6]-phenyl-C61-isomethyl butyrate (PCBM)/aluminum (Al) has been prepared. By optimizing the thermal annealing time and PCBM concentration, the EQE at -60 V was successfully improved from 52946.8% to 68470.9%, which is the highest gain of narrow-band response organic photodetector so far, and the FWHM of ca. 28 tun remains unchanged. We used Nano-IR to confirm that EQE enhancement was attributed to thermal annealing induced diffusion of PCBM into P3HT, thus optimizing the electron trap concentration distribution at the interface between the active layer and the metal top electrode and enhancing carrier injection.

High Stability of Broadband Photomultiplier Organic Photodetector with Metal Ion-Chelated Polymer As an Electron Tunneling Injection Dipole Layer

Highly stable photomultiplication type organic photodetectors with single-polymer containing intramolecular traps as active layer

High-responsivity, High-detectivity Photomultiplication Organic Photodetector Realized by a Metal-Insulator-Semiconductor Tunneling Junction

Optimizing electron injection barriers and hole-trapping ability for high-performance photomultiplication-type ternary organic photodetectors

Ultraviolet to near-infrared broadband organic photodetectors with photomultiplication

Strategies for achieving high-performance photomultiplication-type organic photodetectors and their promising applications

Efficient All‐Polymer Photomultiplication‐Type Organic Photodetectors with Prolonged Crystallization Process

Dual-Band Photomultiplication-Type Organic Photodetectors with Ultrahigh Signal-to-Noise Ratios

Advancing Detectivity and Stability of Near-Infrared Organic Photodetectors via a Facile and Efficient Cathode Interlayer

Adopting Buffer Layer for Improving Signal‐to‐Noise Ratio of Broadband Photomultiplication Type Organic Photodetectors

Panchromatic Photomultiplication-Type Organic Photodetectors with Planar/bulk Heterojunction Structure

Blocking Layer Induced Bi‐Directional Biased Photomultiplication‐Type Near‐Infrared Flexible Organic Photodetectors

Challenges and recent advances in photodiodes-based organic photodetectors

All‐Organic Self‐Powered Photodetector with Ultra‐Flexible Dual‐Polarity Output for Bio‐Signal Detection

Boosting the Performance of Organic Photodetectors with a Solution‐Processed Integration Circuit toward Ubiquitous Health Monitoring

Photomultiplication‐Type Organic Photodetectors for Near‐Infrared Sensing with High and Bias‐Independent Specific Detectivity

Improving the Photomultiplication in Organic Photodetectors with Narrowband Response by Interfacial Engineering

Revealing The Working Mechanism Of Polymer Photodetectors With Ultra-High External Quantum Efficiency

Stabilizing Non‐Fullerene Organic Photodiodes Through Interface Engineering Enabled by a Tin Ion‐Chelated Polymer

Broadband photomultiplication organic photodetectors

Facile light exposure of zinc oxide via interfacial engineering for boosting responsivity and detectivity in organic photodetectors