Abstract:In supported heterogeneous catalysis, supports are used not only to enhance the metal diversion and catalytic stability of metal catalysts, but also to create metal-support interfaces for improving their catalytic performance in specific reactions. For interfaces controlled catalytic system, the construction of abundant and stable interfaces is very important. For this purpose, the physical and chemical properties of the support especially their surface species play the central role. In this work, mesoporous TiO2 (m-TiO2) with ultrahigh surface area (490 m(2)/g) was prepared by the hydrolysis of titanium glycolate complex. Highly dispersed metallic Pt nanoparticles (ca. 2.7 nm) with 1.9 wt% Pt loading were then supported onto the mesoporous TiO2 by a UV deposition method at room temperature. While, for commercial P25 as the support, following the same protocol, ca. 6.7 nm Pt nanoparticles with only 0.2 wt% Pt loading were obtained. The Pt-OH-Fe(III) interfaces were then successfully constructed by a facile deposition-precipitation procedure on both Pt/m-TiO2 and Pt/P25. The as-prepared catalysts exhibited high activity for low temperature CO oxidation, 100% conversion was achieved at 313 K for the m-TiO2 supported Fe(OH)(x)-Pt catalyst, Fe(OH)(x)-Pt/m-TiO2, under 50% humidity condition with weight hourly space velocity (WEISV), ca. 400 L/g(pt)/h (1 vol% CO). In comparison, under the same conditions the P25 supported Fe(OH)(x)-Pt catalyst, Fe(OH)(x)-Pt/P25, reached 100% conversion at 323 K in the first light-off test but gradually deactivated in further test cycles. The performance of Pt-OH-Fe(III) interfaces on m-TiO2 were highly relied on the humidity of the feed gas. Despite the low activity under dry feed gas condition, Pt-OH-Fe(III) interfaces exhibited robust catalytic performance during the long-time and humid/dry feed gas switch test, and the catalytic activity immediately recovered upon introduction of humid feed gas. It was revealed that, m-TiO2 possessed rich surface hydroxyl groups (10.6 mmol/g, 12.5 nm(-2)) which were very sensitive to the humidity of feed gas. Through protons transfer on the surface, the rich and sensitive hydroxyl groups on m-TiO2 maintained the Pt-OH-Fe(III) interfaces from irreversible dehydration By contrast, for the hydroxyl groups on P25, a much lower density and smaller change were detected under both the dry and humid conditions, which resulted in irreversible deconstruction of the Pt-OH-Fe(III) interfaces during the exothermic CO oxidation.

Constructing an oxygen vacancy- and hydroxyl-rich TiO2-supported Pd catalyst with improved Pd dispersion and catalytic stability

Optimizing Alkyne Hydrogenation Performance of Pd on Carbon in Situ Decorated with Oxygen-Deficient TiO2 by Integrating the Reaction and Diffusion

Crystal Facet Induced Single-Atom Pd/CoxOyon a Tunable Metal-Support Interface for Low Temperature Catalytic Oxidation

Self-assembly of a Highly Stable and Active Co3O4/H-TiO2 Bulk Heterojunction with High-Energy Interfacial Structures for Low Temperature CO Catalytic Oxidation

Superior catalytic performance of oxygen vacancy-rich TiO2 supported Pd for formaldehyde oxidation at room temperature

Fabricating Uniform TiO2-CeO2 Solid Solution Supported Pd Catalysts by an in Situ Capture Strategy for Low-Temperature CO Oxidation.

Highly Dispersed and Active Pd Nanoparticles over Titania Support Through Engineering Oxygen Vacancies and Their Anchoring Effect

A Simple Strategy to Improve Pd Dispersion and Enhance Pd/TiO2 Catalytic Activity for Formaldehyde Oxidation: the Roles of Surface Defects

CO Oxidation over Highly Dispersive Supported Palladium Catalysts

Size and Support Effects for Co Oxidation on Supported Pd Catalysts

Interfacial Hydrogen Spillover on Pd-TiO 2 with Oxygen Vacancies Promotes Formate Electrooxidation

Enhancing Activity and Stability of Pd-on-TiO 2 Single-Atom Catalyst for Low-Temperature CO Oxidation through in Situ Local Environment Tailoring

Dispersion and support dictated properties and activities of Pt/metal oxide catalysts in heterogeneous CO oxidation

A first-principles study of reaction mechanism over carbon decorated oxygen-deficient TiO2 supported Pd catalyst in direct synthesis of H2O2

A Vicinal Effect for Promoting Catalysis of Pd1/TiO2: Supports of Atomically Dispersed Catalysts Play More Roles Than Simply Serving As Ligands.

Pd/TiO Nanocatalyst with Strong Metal–Support Interaction for Highly Efficient Durable Heterogeneous Hydrogenation

Stabilizing Catalytic Pt-OH-Fe(III) Interfaces by Mesoporous TiO2 with Rich Surface Hydroxyl Groups

Superior catalytic performance of Pd-loaded oxygen-vacancy-rich TiO2 for formaldehyde oxidation at room temperature

Surface Defect Engineering on Constructing High-Performance Noble Metal Active Sites: A Simple and Cost-Effective Path to High-Performance Oxidation Catalysts

Carbon-Modified Mesoporous Anatase/TiO2(B) Whisker for Enhanced Activity in Direct Synthesis of Hydrogen Peroxide by Palladium

TiO2-nanosheet-assembled Microspheres As Pd-catalyst Support for Highly-Stable Low-Temperature CO Oxidation