A Novel Post-Processing Method for Nonlinearity Correction of FMCW LiDAR

Yi Hao,Yaqi Han,Connie Chang-Hasnain,H. Y. Fu

DOI: https://doi.org/10.1109/oecc56963.2023.10209639

2023-01-01

Abstract:A novel post-processing nonlinearity correction method for the FMCW LiDAR system without the assistance of an auxiliary interferometer is presented. The optimized energy diffusion and the enhanced ranging resolution are experimentally validated.

What problem does this paper attempt to address?

A Novel Method To Enhance The Sensitivity For Two-Degrees-Of-Freedom Straightness Measurement

Cuifang Kuang,En Hong,Qibo Feng,Bin Zhang,Zhifeng Zhang

DOI: https://doi.org/10.1088/0957-0233/18/12/014

IF: 2.398

2007-01-01

Measurement Science and Technology

Abstract:A low cost and high precision system which can measure two-degrees-of-freedom straightness simultaneously is proposed based on a laser collimator. In the system, a miniature fiber coupled diode laser generates a collimating beam. The sensitivity of the straightness error measurement is magnified by a factor of 4 compared with the lateral movement of the retro-reflector itself after the multi-reflections. A Renishaw ML10 laser interference measurement system was used to verify the developed system in a series of experiments in the laboratory environment. Experimental results agree with the expected results. The two-dimensional straightness error measurement had linear correlativity close to 1 and the standard one-to-one deviation error was better than 0.32 mu m obtained over a travel range of 600 mu m.
Frequency Modulation Nonlinear Correction and Ranging in FMCW LiDAR

Yuchen Jiang,Miao Hu,Mengmeng Xu,Haozhen Li,Xuefang Zhou,Meihua Bi,Sunqiang Pan,Chong Liu

DOI: https://doi.org/10.1109/jqe.2024.3454604

IF: 2.5

2024-10-02

IEEE Journal of Quantum Electronics

Abstract:The linearity of the laser frequency modulation is a crucial factor that affects the performance of the frequency-modulated continuous wave (FMCW) LiDAR ranging. Nonlinearity can influence ranging resolution and introduce errors. This paper proposes a method for correcting frequency modulation nonlinearity based on waveform preprocessing for the modulation signal of the laser. After correction, the residual nonlinearity (1-r2) of the laser is reduced to for the up-sweeping and for the down-sweeping using the modulation signal with the repetition frequency of 50 kHz. The full-width at half of the maximum (FWHM) of the spectrum decreases by 86% compared to pre-correction, resulting in the ranging error of 0.37% at the distance of 38 cm. With distances of 0.90 m, 1.80 m, 2.89 m, and 4.13 m, respectively, the ranging error stabilizes at 0.2%, and the minimum deflection of distance can reach .

engineering, electrical & electronic,optics,physics, applied,quantum science & technology
Nonlinear Frequency Correction Technology of DFB Laser with High Frequency Modulation for FMCW LiDAR

Gou Jiajun,Shen Yonghang

DOI: https://doi.org/10.3788/gzxb20235202.0214003

IF: 0.6

2023-01-01

ACTA PHOTONICA SINICA

Abstract:With the development of autonomous driving technology, lidar technology has also been rapidly developed. As one of the Lidar systems, Frequency Modulated Continuous Wave (FMCW) calculates the distance of the target by detecting the beat signal frequency of the local light and the signal light. It can also calculate the velocity of the target by the optical Doppler effect. Compared with traditional time of flight FMCW lidar has many advantages. First, FMCW utilizes the principle of coherent detection to filter out the background noise effectively. The peak power of the continuous wave is small, which is safe for human eyes. Secondly, the FMCW system can detect both the speed and distance of the target. Thirdly, when it comes to tong range detection, the FMCW system doesn't need a Single photon detector, so it can reduce the cost. However, in the field of autonomous driving, with the increase of imaging speed, the laser modulation rate has to increase, and then the nonlinearity of the laser source rises. as a result, the frequency of the beat signal varies greatly and the precision and resolution of the detection become worse. The resampling method, photoelectric negative feedback method and pre-correction method can solve this problem. Considering the cost of the FMCW system, we use the pre-previous studies based on the auto driving application. This paper studies the nonlinear pre-correction of DFB laser in high speed tuning by simulation and experiments at the same time. Here, we first briefly introduce the principle of FMCW detection and analyze the influence of optical nonlinearity on detection precision. Secondly, we carry out the DFB simulation and use the Simulink toolbox of MATIAB to establish the temperature dominated tuning model of the DFB laser. Then, we assume the parameters of the DFB laser and analyze the nonlinearity distortion with the modulation rate of 100 kHz. Because the temperature hysteresis has most of the influence on optical nonlinearity, here, we do not consider the carriers' effects on frequency turning. After that, we use the iterative algorithm to correct the nonlinearity of optical frequency for many times and analyze the convergence of this algorithm. The correctness of the DFB module and iterative algorithm is verified. There are three steps in the iterative algorithm. At first, we calculate the optical frequency by STFT or Hilbert transform from the beat signal, then we calculate the differential value between two adjacent time points in the arbitrary wave generator and figure out the relative value of each point. At last, after the linear transform, we can get the real value of arbitrary wave generator at each time. Based on the simulation, we first set up an experimental platform to correct the nonlinearity of the existing DFB laser with two times of iterations. To analyze the effect of the nonlinear correction method, we detect two adjacent targets with the distance of 51.5 m and 60.5 m. The correctness of the simulation model and an iterative algorithm is verified. The results of the simulation and experiment show that the iterative method can effectively reduce the nonlinearity of the light source. With the increase of the number of iteration times, the nonlinearity improvement of the light source becomes more obvious. The nonlinearity of the tower and upper area of the optical frequency of the light source decreases from 0.050 0 and 0.020 0 to 0.004 2 and 0.002 6 respectively after two times iterations, which is consistent with the simulation. The detection results of two adjacent targets show that the 3 dB bandwidth of the detection system is effectively reduced after correction, which proves the feasibility of the iterative algorithm and modulation module.
Nonlinearity Correction Technology for Light Source of Frequency-Modulated Continuous-Wave Light Detection and Ranging(Invited)

Tan Yidong,Lin Chenxiao

DOI: https://doi.org/10.3788/lop232667

2024-01-01

Laser & Optoelectronics Progress

Abstract:Frequency-modulated continuous-wave(FMCW)light detection and ranging(LiDAR)has the advantages of noncontact measurements,resistance to ambient light interference,high resolution,and the ability to simultaneously determine speed and distance information.In recent years,it has been widely used in various fields,including aerospace,precision manufacturing,and autonomous driving.The ranging performance of FMCW LiDAR significantly depends on the sweep linearity of its light source,which is typically influenced by several factors,such as uneven stress stretching,temperature variations,and circuit noise.These factors decrease the ranging resolution and accuracy.The influence of light source nonlinearity in FMCW LiDAR is analyzed theoretically,and research progress in different types of nonlinearity correction techniques is presented.The characteristics,advantages,and disadvantages of each method are summarized to provide a reference for future research.
Real-Time LiDAR Data Assocation Aided by IMU in High Dynamic Environment

Jinhong Xu,Jiajun Lv,Zaishen Pan,Yong Liu,Yinan Chen

DOI: https://doi.org/10.1109/RCAR.2018.8621627

2018-01-01

Abstract:In recent years, with the breakthroughs in sensor technology, SLAM technology is developing towards high speed and high dynamic applications. The rotating multi line LiDAR sensor plays an important role. However, the rotating multi line LiDAR sensors need to restructure the data in high dynamic environment. Our work is to propose a LiDAR data correction method based on IMU and hardware synchronization, and make a hardware synchronization unit. This method can still output correct point cloud information when LiDAR sensor is moving violently.
Non-linear processing based on Dolphin inspired real LFM signals for enhanced delay-Doppler resolution

Dongzhou Zhan,Hangfang Zhao,Wen Xu

DOI: https://doi.org/10.1109/OCEANS-TAIPEI.2014.6964562

2014-01-01

Abstract:In this paper, we study two non-linear processing approaches, inspired by biosonars, to enhance the delay-Doppler resolution. We use real linear frequency modulated (LFM) signals to fulfill a model, based on an abstraction and modification of the dolphin signals of certain species. With the help of Hilbert transform, two delay-Doppler images can be generated through single LFM signal. Non-linear algorithms are then applied and analyzed for producing a super delay-Doppler resolution when combining the images together. We also investigate the detection performance of those algorithms. Overall, the developed non-linear processing offers a great improvement in delay-Doppler resolution while the detection performance is close to that of the conventional matched filter receiver without significant increase in system or computational complexity.
Interpolation linearization predistortion technology for FMCW LiDAR

Honggang Chen,Le Zhao,Leilei Hu,Long Chen,Bo Zhang,Yong Luo,Xuerui Liang,Linfei Gan

DOI: https://doi.org/10.1364/ao.515530

IF: 1.9

2024-02-15

Applied Optics

Abstract:Honggang Chen, Le Zhao, Leilei Hu, Long Chen, Bo Zhang, Yong Luo, Xuerui Liang, Linfei Gan Frequency-modulated continuous-wave (FMCW) laser ranging technology is an important development direction of light detection and ranging ... [Appl. Opt. 63, 1538-1545 (2024)]

optics
Beam-Steering Based on Dispersive Optical Phased Array for FMCW LiDAR Application

Xingyi Jiang,Zhaoyang Zhang,Qikai Huang,Qiang Zhang,Jianyi Yang,Hui Yu

DOI: https://doi.org/10.1364/ofc.2024.th2a.31

2024-01-01

Abstract:We demonstrate dispersive optical phased arrays based on the Si3N4-on-Si platform. Two-dimensional beam steering across a 45.6 °× 10 °FOV with a beam width of 1.45 °× 0.032 °is achieved by wavelength tuning alone. Besides, FMCW ranging operation at a target distance of 10 m are experimentally performed.
Nonlinearity Correction of FMCW SAR Based on Homomorphic Deconvolution.

Jian Yang,Chang Liu,Yanfei Wang

DOI: https://doi.org/10.1109/LGRS.2012.2227667

IF: 5.343

2013-01-01

IEEE Geoscience and Remote Sensing Letters

Abstract:In this letter, a novel algorithm based on homomorphic deconvolution is proposed to give a theoretically unbiased estimation of transmitted nonlinearity in the beat signal in frequency-modulated continuous-wave synthetic aperture radar. Transmitted and received nonlinearities in the beat signal are separated in the Cepstrum domain by using a controllable delay line, and the transmitted nonlinearit...
Frequency Modulation Nonlinearity Correction for FMCW SAL Based on WVD With Gradient Rotation Enhancement

Ruihua Shi,Yinshen Wang,Bingnan Wang,Maosheng Xiang

DOI: https://doi.org/10.1109/lgrs.2023.3328868

IF: 5.343

2023-11-14

IEEE Geoscience and Remote Sensing Letters

Abstract:Frequency modulation continuous wave (FMCW) synthetic aperture ladar (SAL) system can support the generation and processing of large bandwidth signals, which has strong capabilities in target detection, description, and identification. However, frequency modulation nonlinearity of the transmitted signal has become a bottleneck problem that restricts the high-resolution ranging of FMCW SAL. This letter establishes an echo model with nonlinearity and proposes a nonlinear phase estimation and compensation method based on Wigner–Ville distribution (WVD) with gradient rotation enhancement. First, we establish the nonlinearity model of the internal calibration signal in the time–frequency (TF) domain and use WVD to calculate the TF distribution (TFD). Second, the TFD is enhanced by rotating gradient vector, which can also eliminate noises and false components in the TFD. Then, the nonlinear phase of the transmitted signal is estimated by establishing a nonlinearity model in the TF domain. Finally, the residual video phase (RVP) filtering is introduced to eliminate the range-dependent nonlinearity and achieve nonlinearity correction of echoes at any range. Experiments and real data tests show that the method proposed in this letter can accurately estimate and correct the nonlinearity of the dechirp signal, which effectively improves the range resolution of FMCW SAL.

imaging science & photographic technology,remote sensing,engineering, electrical & electronic,geochemistry & geophysics
A Dispersion Compensation Method Based on Resampling of Modulated Signal for FMCW Lidar

Shuo Jiang,Bo Liu,Shengjie Wang

DOI: https://doi.org/10.3390/s21010249

IF: 3.9

2021-01-02

Sensors

Abstract:In order to eliminate the nonlinearity in the laser modulation process, the dual-interferometers system is often adopted in the frequency modulation continuous wave (FMCW) laser ranging. However, the dispersion mismatch between the fiber reference interferometer and the measurement interferometer will lead to the decrease in ranging accuracy and resolution. In this paper, a dispersion compensation method based on resampling with a modulated signal is proposed. Since the beat signal of the end face of the delay fiber is not affected by dispersion mismatch, it can be modulated to generate a signal whose phase is proportional to that of the target spatial signal. Then, the modulated signal is regarded as the reference clock to sample the target spatial signal. Thereby, the influence of the dispersion mismatch between the two optical interferometers can be eliminated. In this article, simulation is performed to verify the effect of this method, and an experiment is carried out on the target at the distance of 2.4 m. Experiments show that the full width at half maximum (FWHM) of the distance spectrum after dispersion compensation is consistent with the reflected signal from the end face of the delay fiber, and the standard deviation of multiple measurements reached 10.12 μm.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Optimization of Longitudinal Alignment of an 4<i>f</i> System in a Compact Vectorial Optical-Field Generator Based on a High-Resolution Liquid Crystal Spatial Light Modulator

Mingyu Li,Yuanzheng Liu

DOI: https://doi.org/10.3390/photonics10080894

IF: 2.536

2023-01-01

Photonics

Abstract:Vectorial optical fields have garnered significant attention due to their potential applications in areas such as optical nano-fabrication, optical micromachining, quantum information processing, optical imaging, and so on. Traditional compact vectorial optical generators with amplitude modulation perform poorly in terms of diffraction effect reduction. To tackle this problem, the refractive 4f system in amplitude modulation is longitudinally aligned using an optimization approach presented in this research. The phase images used for longitudinal alignment are loaded into the liquid crystal spatial light modulator (SLM), and the distance between the lens and the mirror in the reflective 4f system is adjusted for longitudinal alignment by compensating for the neglected phase in the integrated module for the compact vectorial optical-field generator. The spot images collected by the CCD are processed using the improved eight-direction Sobel operator and Roberts function, and the longitudinal alignment in the reflective 4f system is determined by the sharpness of the image. The sharpness of the edges of the lines and the overall image are both enhanced after optimization compared to before optimization. The results demonstrate that the proposed method can effectively reduce the longitudinal alignment error of the reflective 4f system in the amplitude modulation of the compact vectorial optical-field generator, lessen the diffraction effect, and improve the performance of the system.
Sunlight Noise Mitigation in FMCW LiDAR Using FADOF

Longfei Yin,Wei Tang,Ziwei Geng,Haodi Zhan,Lei Chen,Dasheng Qian,Guohua Wu,Bin Luo

DOI: https://doi.org/10.1109/jphot.2024.3388326

IF: 2.4

2024-04-23

IEEE Photonics Journal

Abstract:This paper examines the potential of utilizing a Faraday anomalous dispersion optical filter (FADOF) to enhance noise reduction in a FMCW LiDAR (Frequency-Modulated Continuous-Wave Laser Detection And Ranging) system. While the FMCW LiDAR itself demonstrates a certain level of robustness, it may fail to operate effectively in the presence of significant background noise interference. To address this challenge, we have proposed a validation experiment utilizing FADOF technology. Specifically, we have introduced a FADOF component at the optical receiving end of the FMCW LiDAR, and we have implemented a dynamic frequency stabilization method that combines frequency stability with frequency modulation for the laser source in the transmitter. By integrating FADOF into the FMCW LiDAR system to mitigate external noise, we conduct indoor and outdoor validation experiments. In the outdoor experiment, we introduce real sunlight background noise into the system, allowing it to directly illuminate the receiver. We then filter the light using FADOF and a 10 nm filter, separately. The experimental results confirm that the FMCW LiDAR system, when equipped with FADOF, can operate normally in intense background light noise, with a noise resistance capability at least twice as effective as the 10 nm filter. Additionally, the system achieves a detection range of at least 17 meters under direct sunlight conditions. This study has the potential to extend the application of LiDAR systems to more extreme environments with strong background noise, enabling their functionality in a broader range of scenarios.

engineering, electrical & electronic,optics,physics, applied
Laser Feedback Frequency-Modulated Continuous-Wave LiDAR and 3-D Imaging.

Yifan Wang,Ziyu Hua,Jiachen Shi,Zongren Dai,Jiagang Wang,Liyang Shao,Yidong Tan

DOI: https://doi.org/10.1109/tim.2023.3249246

IF: 5.6

2023-01-01

IEEE Transactions on Instrumentation and Measurement

Abstract:We propose and demonstrate a novel light detection and ranging (LiDAR) system for 3-D imaging, combined with laser feedback interferometry (LFI) and frequency-modulated continuous-wave (FMCW). Compared with the conventional FMCW method, the intracavity interference between the echo signal and local oscillator enhances the amplitude of the generated beat signal effectively, which improves the sensitivity in weak-signal detection with low photon consumption. The improvement is still effective even with frequency modulation nonlinearity. Besides, the system inherits the advantages of FMCW, possessing the capacity to measure position and velocity simultaneously. In experiments, the validity of distance and velocity measurement is demonstrated, and 3-D imaging is realized by employing a pair of beam scanners. With a less than $200 \mu \text{W}$ probe beam, the system achieves imaging over 65 m away in various scenes with good fidelity, and the distance resolution is better than 1 mm. A portable prototype is also designed and fabricated. Overall, the proposed system possesses high echo-signal sensitivity, simple structure, and dynamic information availability, which provides a new idea for FMCW-LiDAR optimization for practical applications.
Linearization of wavelength sweeping lasers for the construction of 4-D FMCW LiDAR images of slow-moving objects using baseband beat note signals

Yu-Kuan Tsai,Zheng-Xiang Liao,Yu-Xiang Lin,H-S Chen,Jack Jia-Sheng Huang,Pei-Hsun Wang,Chia-Chien Wei,You-Chia Chang,Yung Hung,Jin-Wei Shi

DOI: https://doi.org/10.1364/OE.524443

2024-05-20

Abstract:A FMCW LiDAR system of both the distributed feedback laser and external cavity laser is established in baseband beat notes, rather than up-conversion to an intermediate frequency to exclude flicker noise. Meanwhile, utilizing fast-scanning MEMS mirrors, high-quality real-time (1 fps) 4-D images of the slow-moving object (10 mm/s) can be directly constructed at the baseband with a central frequency as low as 100 kHz and a small Doppler shift. The proposed LiDAR architecture based on such a low-frequency baseband significantly improves the optical power budget on the transmitter side and eliminates the costly high-speed sampling circuits on the receiver side.
Dynamic Frequency-Modulated Continuous-Wave LiDAR Coupled Through a Rotary Interface

Caiming Sun,Zhen Chen,Fei Teng,Qi Wang,Jing Lin,Binghui Li,Wu Shi,Dagong Jia,Xuejin Li,Aidong Zhang

DOI: https://doi.org/10.1109/jlt.2023.3289161

IF: 4.7

2023-01-01

Journal of Lightwave Technology

Abstract:In order to acquire the tracking information across a rotary joint, a dynamic frequency-modulated continuous-wave (FMCW) laser ranging system is designed to couple through a rotary interface. A setup for FMCW light detection and ranging (LiDAR) is proposed to couple through a fiber optic rotary joint (FORJ), whose optical path is able to eliminate the influence of rotary coupling on the generation of beat frequency. This FMCW LiDAR uses real-time correction for nonlinear laser chirps by synchronizing the FMCW measurement signals with laser injection current at data acquisition (DAQ). Then, phase variations induced by rotary coupling are excluded from the FMCW measurements. The acquisition rate is kept much higher than the rotation speed of FORJ, in order to reduce the influence of rotary coupling on the real-time nonlinearity correction. The linearization of laser frequency modulation through a FORJ is conducted by resampling of over 3000 intervals interpolated in every up-sweep or down-sweep of 25 μs, with measurement signals stretched or compressed in time domain. With the FORJ rotating at the speed of 10°/s in both clockwise and anticlockwise directions, the clear and robust beat signals are achieved. The statistical distributions of measured 50-cm distance under rotary conditions are found out to be similar to that under stationary condition.

engineering, electrical & electronic,optics,telecommunications
Nonlinear Phase Estimation and Compensation for FMCW Ladar Based on Synchrosqueezing Wavelet Transform

Rongrong Wang,Maosheng Xiang,Bingnan Wang,Chuang Li

DOI: https://doi.org/10.1109/lgrs.2020.2997999

IF: 5.343

2021-07-01

IEEE Geoscience and Remote Sensing Letters

Abstract:Frequency modulation continuous wave (FMCW) laser radar (Ladar) is a new radar system suitable for long-range detection and high-resolution imaging. However, the transmitted signal inevitably suffers from nonlinear frequency modulation errors which reduce the quality of Ladar imaging. We propose a nonlinear phase estimation and compensation method based on synchrosqueezing wavelet transform (SST). We first use SST to synchrosqueeze the dechirp signal containing a reference range in time–frequency domain and obtain the time–frequency information of the reference dechirp signal. As SST could aggregate the time–frequency distribution of noise, the proposed method is effective even in a noisy environment. A nonlinearity model in time–frequency domain is then built to estimate the nonlinear phase of the transmitted signals by using the time–frequency information of the reference dechirp signal. For the case of long-range detection, we adopt a residual video phase filtering to convert the nonlinear phase of the dechirp signal to range-independent phase errors. Finally, the nonlinearity of the dechirp signal is compensated using the estimated nonlinear phase of the transmitted signals. The experimental and real data tests show that the proposed method effectively improves the resolution of long-range Ladar imaging by compensating for the nonlinearity of the dechirp signal. Its advantage is the effectiveness for noisy and multicomponent FMCW Ladar signals.

imaging science & photographic technology,remote sensing,engineering, electrical & electronic,geochemistry & geophysics
Virtually Imaged Phased-Array-based 2D Nonmechanical Beam-Steering Device for FMCW LiDAR.

Zhi Li,Zihan Zang,H. Y. Fu,Yi Luo,Yanjun Han

DOI: https://doi.org/10.1364/ao.414128

IF: 1.9

2021-01-01

Applied Optics

Abstract:Nonmechanical beam-steering devices are of importance to achieve fast, compact, and reliable LiDAR. We propose a 2D nonmechanical beam-steering device based on a virtually imaged phased array (VIPA) for frequency-modulated continuous-wave (FMCW) LiDAR. In the design, 2D nonmechanical beam steering and high-resolution FMCW ranging can be achieved at the same time by wavelength tuning. The design formulas of the VIPA-based 2D disperser are greatly simplified by introducing appropriate approximation, and a feasible design procedure is proposed for the first time, to the best of our knowledge. Based on the proposed method, several design examples with different optimal properties are exhibited.
Investigation of Anti-Interference Characteristics of Frequency-Hopping LiDAR

Yonglong Chen,Yingke Xie,Cheng Liu,Ligong Chen

DOI: https://doi.org/10.1109/lpt.2021.3125702

IF: 2.6

2021-12-15

IEEE Photonics Technology Letters

Abstract:We have designed an anti-interference LiDAR based on frequency-hopping (FH) modulated for autonomous vehicles. It uses the cross-correlation method to analyze and process the signals. The effectiveness of the anti-interference capability of the LiDAR is verified by ranging relative error (RE). The result shows that the RE of range measuring is minor than ±0.9%. It demonstrated that the proposed LiDAR in the letter provides a reproducible and reliable way to realize ranging detection. In addition, the experiment results testify that the system has an excellent anti-interference capability with other interference of LiDARs.

engineering, electrical & electronic,optics,physics, applied
Long distance high resolution FMCW laser ranging with phase noise compensation and 2D signal processing

Jia-Yi Ke,Zi-Qi Song,Pei-Si Wang,Zhong-Ming Cui,Di Mo,Miao Lin,Ran Wang,Jin Wu

DOI: https://doi.org/10.1364/AO.454001

2022-04-20

Abstract:A long distance high resolution frequency-modulated continuous wave (FMCW) laser rangefinder with phase noise compensation and two-dimensional (2D) data processing skills is developed. Range-finding ladar consists of a continuously chirped laser source, an auxiliary reference interferometer, and a monostatic optical transceiver for target illumination and return photon collection. To extend the range unambiguity and lower the electronic processing bandwidth, a two-step laser frequency chirping scheme is adopted, where a long pulse width, small frequency bandwidth laser chirping signal are used in step 1 for coarse distance estimation, and a short pulse width and large frequency bandwidth laser chirping signal are applied afterwards for step 2 high resolution distance realization. An auxiliary reference interferometer is to record the phase noise originated from the laser source to compensate for phase errors induced in the target return photons. The 2D data processing skill helps to coherently sum up all the phase noise removed echo photons to achieve high resolution range peak extraction with high detection sensitivity. Experimental demonstration shows that the proposed FMCW ladar at 1550 nm wavelength with a laser chirping bandwidth of 10 GHz and electronic processing bandwidth of 200 MHz can measure a corner cube test target in an outdoor atmospheric environment, and the measurement results are 12013.905 m with a 2.4 cm range resolution under strong return photon levels and 12013.920 m with a 2.5 cm range resolution under weak return photon levels.

A Novel Post-Processing Method for Nonlinearity Correction of FMCW LiDAR

A Novel Method To Enhance The Sensitivity For Two-Degrees-Of-Freedom Straightness Measurement

Frequency Modulation Nonlinear Correction and Ranging in FMCW LiDAR

Nonlinear Frequency Correction Technology of DFB Laser with High Frequency Modulation for FMCW LiDAR

Nonlinearity Correction Technology for Light Source of Frequency-Modulated Continuous-Wave Light Detection and Ranging(Invited)

Real-Time LiDAR Data Assocation Aided by IMU in High Dynamic Environment

Non-linear processing based on Dolphin inspired real LFM signals for enhanced delay-Doppler resolution

Interpolation linearization predistortion technology for FMCW LiDAR

Beam-Steering Based on Dispersive Optical Phased Array for FMCW LiDAR Application

Nonlinearity Correction of FMCW SAR Based on Homomorphic Deconvolution.

Frequency Modulation Nonlinearity Correction for FMCW SAL Based on WVD With Gradient Rotation Enhancement

A Dispersion Compensation Method Based on Resampling of Modulated Signal for FMCW Lidar

Optimization of Longitudinal Alignment of an 4<i>f</i> System in a Compact Vectorial Optical-Field Generator Based on a High-Resolution Liquid Crystal Spatial Light Modulator

Sunlight Noise Mitigation in FMCW LiDAR Using FADOF

Laser Feedback Frequency-Modulated Continuous-Wave LiDAR and 3-D Imaging.

Linearization of wavelength sweeping lasers for the construction of 4-D FMCW LiDAR images of slow-moving objects using baseband beat note signals

Dynamic Frequency-Modulated Continuous-Wave LiDAR Coupled Through a Rotary Interface

Nonlinear Phase Estimation and Compensation for FMCW Ladar Based on Synchrosqueezing Wavelet Transform

Virtually Imaged Phased-Array-based 2D Nonmechanical Beam-Steering Device for FMCW LiDAR.

Investigation of Anti-Interference Characteristics of Frequency-Hopping LiDAR

Long distance high resolution FMCW laser ranging with phase noise compensation and 2D signal processing