Abstract:DC HTS power cable has drawn attention as an ideal solution for transmitting massive electric power for long distances. As one of the accessories of the DC HTS power cable, the stop joint box (SJB) is an essential component for long distance transmission cable connections and separation of the cooling section. The main insulation of the SJB is a polypropylene laminated paper (PPLP) which is the same as that of the DC HTS power cable. In order to separate the cooling section, an epoxy spacer is located at the center of the SJB. For the insulation design of the SJB, DC electric field analysis should be done to determine the shape of insulation structure and their physical dimensions. As DC field distribution was mainly determined by the ratio of electrical conductivity of the insulating materials, information about the electrical conductivity of dielectric material should be obtained. But the reliable data of electrical conductivity of insulating material, especially in cryogenic environment could not be easily obtained. In this paper, we focused on the measurement of electrical conductivity of PPLP in LN2 according to the existence of copper deposition. Due to the infiltration of LN2 between the edge of the electrode and PPLP, the accuracy of measured electrical conductivity might be lowered. Thus, in order to prevent the infiltration of LN2 into PPLP specimen, PPLP specimen deposited by copper was adopted. On the basis of the measurement of PPLP in LN2, the initial SJB model was designed based on the joint box for a conventional AC oil-filled (OF) power cable. Then, two kinds of improved SJB models with different epoxy spacer configurations were considered and simulated using the finite element method (FEM). Consequently, it was possible to design the insulation structure of the SJB of a DC HTS power cable based on the DC electric field analysis.

Qualitative Study On Cable Breakage of Nb<sub>3</sub>Sn CICC Based On Direct Current Potential Drop Method

Qualitative Study On Cable Breakage of Nb 3 Sn CICC Based On Direct Current Potential Drop Method

Numerical Simulation of the Cable Breakage Based on Electromagnetic NDE Method for Nb3Sn Cable-In-Conduit Conductors

Research on DC Breakdown Characteristics for the Insulation of 10 Kv AC XLPE Cables

DC Breakdown and Surface Potential Behavior of Epoxy/Al<sub>2</sub>O<sub>3</sub> Nanocomposites at Cryogenic Temperature

Metallographic Investigation of First Full-Size High-Jc Nb3Sn Cable-in-conduit Conductor after Cyclic Loading Tests

Identification Of Wire Breakage Status Based On The Measurement And Inversion Of Magnetic Field Aiming At Applications To Cable In Conduit Conductors Of Iter Magnets

Study on the Nb3Sn Rutherford Cable for High-Energy Accelerators

Numerical Investigation on Transverse Heat Transfer Properties in Cross Section of Full Size Nb3Sn CICC ITER Conductor

DC Performance Measurement and Assessment of Nb 3 Sn Cable-In-Conduit Conductor for CFETR CS Model Coil

Analysis on stability margin of Nb/sub 3/Sn Cable-in-Conduit-Conductor

Indentation Effects on Strain Sensitivity of Critical Current for Internal-Tin Nb3Sn Strand

Numerical Simulation of the Mechanical Properties of the $\hbox{nb}_{3}\hbox{sn}$ CICCs under Transverse Cyclic Loads

Typical Defect Simulation of 110kv Cable and Its Partial Discharge Characteristic Test

Deformation Behavior and Degradation on Rutherford Cabling of Nb 3 Sn Wires

Non-destructive Evaluation of Critical Current on a Bi-2212 First Stage Cable Based on Numerical Analysis of the Remnant Field Distributions

Enhancement of Quantitative Evaluation of Wire Breakage from Measured Magnetic Field with Denoising Algorithm

A study on the measurement of electrical conductivity of PPLP in LN2 for a stop joint box of DC HTS power cable

Local plastic deformation effects on the critical current of high-J c Nb 3 Sn strands under uniaxial strain

Test Research on DC Partial Discharges of Cross Linked Polyethylene Cable