Abstract:The mechanisms controlling the dependence on low-velocity flow of the piloted ignition of a solid material under external radiant heating is investigated through a numerical modeling. The poly (methyl methacrylate) (PMMA) was used as the fuel. The objective of the present study is to gain insight into the intrinsic ignition mechanisms of a solid fuel, as well as to gain a more comprehensive understanding of the dynamical characteristics of the ignition process near the extinction limit. For this purpose, a two-dimensional numerical model has been developed using the Fire Dynamic Simulator (FDS5) code, in which both solid-phase and gas-phase reactions are calculated. Two radiant heat flux, which are 16 and 25 kW/m 2 were studied, and an external air flow was varied from 3 to 40 cm/s. The simulation results showed that transient gas reaction flashed before a continuous flame was attached to the sample surface for gas flow velocities lower than a critical value. As the flow velocity is reduced, the flashing time, which is defined as the time when any flame is seen above the sample surface, decreases, while the duration of flashing increases. The solid surface temperature and mass flow rate increase rapidly during flashing. The ignition time, which is defined as the time when a continuous flame is attached to the fuel surface, decreases, reaches a minimum, and then increases until ignition cannot occur. Mechanisms were considered to explain the ''V-shaped" dependence of ignition time on flow-velocity, and two regimes were identified each having a different controlling mechanism: the mass transport regime where the ignition delay is controlled by the mixing of oxygen and pyrolyzate; and the heat transfer regime where the ignition delay is controlled by changes in convection heat losses and critical mass flux for ignition. With the decrease of the airflow velocity, the critical mass flux shows a trend of decreasing and then increasing, which is dominated by the mixing of the pyrolyzate and the oxidizer, while the critical temperature monotonically decreases, which is dominated by a reduction of the net heat flux at the fuel surface. The results provide further insight into the ignition behavior of solid fuel under low-velocity flow environment, and guidance about fire safety in microgravity environments.

Asymptotic and Approximate Solutions for Piloted Ignition of Thermally Thick Solids under Power-Law Heat Flux

Approximate Analytical Solutions for Transient Mass Flux and Ignition Time of Solid Combustibles Exposed to Time-Varying Heat Flux

Approximate Analytical Solutions for Temperature Based Transient Mass Flux and Ignition Time of a Translucent Solid at High Radiant Heat Flux Considering In-Depth Absorption

Piloted Ignition at Square Corners of 2D Rectangular Solids: Asymptotic and Approximate Solutions

Auto-ignition of Thermally Thick PMMA Exposed to Linearly Decreasing Thermal Radiation

Numerical Study on Pilot Ignition of a Thermally-Thick Solid Fuel with Low-Velocity Airflow in Microgravity

Piloted Ignition of Solid Fuels at Low Ambient Pressure and Varying Igniter Location

Ignition of Polymers under Exponential Heat Flux Considering Both Surface and In-Depth Absorptions

Pyrolysis and Piloted Ignition of Thermally Thick PMMA Exposed to Constant Thermal Radiation in Cross Forced Airflow

An Alternative Way for the Ignition Times for Solids with Radiation Absorption In‐depth by Simple Asymptotic Solutions

Experimental, Numerical and Theoretical Analyses of the Ignition of Thermally Thick PMMA by Periodic Irradiation

The Use of Time to Ignition Data for Characterizing the Thermal Inertia and the Minimum (critical) Heat-Flux for Ignition or Pyrolysis

Ignition Times for Thermally Thick and Intermediate Conditions in Flat and Cylindrical Geometries

Experimental, analytical and numerical investigation on auto-ignition of thermally intermediate PMMA imposed to linear time-increasing heat flux

Piloted Ignition and Extinction for Solid Fuels

Asymptotic, approximate, and numerical solutions for the heatup and pyrolysis of materials including reradiation losses

Accelerated Piloted Ignition on an Edge of a PMMA Cube

Effects of Material Thickness on Ignition Times and Creeping Flame Spread in the Thermal Regime: Theory, Analytical Solution and Experimental Justification

Analytical Prediction of Heat Transfer and Ignition Time of Solids Exposed to Time-Dependent Thermal Radiation

Effects of Combined Surface and In-Depth Absorption on Ignition of PMMA.

Theoretical Analysis on the Transient Ignition of a Premixed Expanding Flame in a Quiescent Mixture