Abstract:In,this work a previously proposed empirical and analytical criterion for extinction is numerically extended and validated for varying fuel dilution, oxidant dilution, strain rate, and surface temperature. The output of this work is presented in two parts: the current Part I uses simple kinetics and constant thermal transfer properties and Part II uses detailed kinetics, varying thermal transfer properties, flame radiation feedback and flame suppression agents in order to demonstrate that conclusions from the simplified model are still valid. In addition this work goes beyond the concept of critical flame temperature or mass flux for extinction by including the influence of slow chemical kinetics through the Damkohler number which becomes even more important for commonly used fire retarded materials.Extinction of flames on solid fuels is modeled by decoupling the pyrolysis chemistry from the gas-phase combustion chemistry using the flame energy feedback versus pyrolysis rate curves and an energy balance at the surface. This approach has the advantage of identifying and deducing key materials properties for solid and gaseous phase from experiments. Simulations are performed in a planar stagnation-point flow diffusion flame configuration using one-step Arrhenius chemical kinetics and a simplified transport model with Lewis number equal to unity. Only quasi-steady conditions are considered for the gaseous phase even. if the pyrolysis rate of the solid is transient because the response time for the solid phenomena is, in general, much larger than the response (diffusion) time for the gaseous phenomena.It is found that at high pyrolysis rates and low straining rates (infinitely fast kinetics regime) there is no leakage of oxygen to the surface of solid fuel. However, as the solid fuel extinction is approached, oxygen leakage occurs because the effective air to fuel mass stoichiometric ratio becomes less than one owing to fuel dilution near the surface. At high straining rates, solid combustion cannot be sustained at any pyrolysis rate. In the infinitely fast kinetics regime, an appropriate scaling has been developed which collapses the convective heat flux curves onto a single one. In general, the critical pyrolysis fuel mass flux exhibits a universal behavior for variation of various model parameters when plotted versus a modified Damkohler number, and becomes constant when the latter is sufficiently high. Comparison with experiments is discussed, and the implications of the criterion for characterizing ignition flammability properties of solid fuels are also discussed. (C) 2012 Elsevier Ltd. All rights reserved.

Asymptotic, approximate, and numerical solutions for the heatup and pyrolysis of materials including reradiation losses

Material Pyrolysis Properties, Part I: an Integral Model for One-Dimensional Transient Pyrolysis of Charring and Non-Charring Materials

The Use of Time to Ignition Data for Characterizing the Thermal Inertia and the Minimum (critical) Heat-Flux for Ignition or Pyrolysis

Assessing an Experimental Approach for Chemical Explosive Mode and Heat Release Rate Using DNS Data

Similarity solutions and applications to turbulent upward flame spread on noncharring materials

Asymptotic and Approximate Solutions for Piloted Ignition of Thermally Thick Solids under Power-Law Heat Flux

Predicting the Pyrolysis Temperature for Thermally Thin Fuels in Opposed-Flow Flame Spread in the Thermal Regime

Pyrolysis of a finite thickness composite material

Numerical Study of Fluid Flows and Heat Transfer of Aviation Kerosene with Consideration of Fuel Pyrolysis and Surface Coking at Supercritical Pressures

Material Pyrolysis Properties, Part II: Methodology for the Derivation of Pyrolysis Properties for Charring Materials

Creeping Flame Spread: Energy Balance and Application to Practical Materials

Model Validation and Parametric Study of Fluid Flows and Heat Transfer of Aviation Kerosene with Endothermic Pyrolysis at Supercritical Pressure

Exact Solution for the Rate of Creeping Flame Spread over Thermally Thin Materials

Experimental and Numerical Simulation Study of Typical Semi-Transparent Material Pyrolysis with In-Depth Radiation Based on Micro and Bench Scales

Critical Mass Pyrolysis Rates for Extinction of Fires over Solid Materials

Modeling and Simulation of Supercritical-Pressure Turbulent Heat Transfer of Aviation Kerosene with Detailed Pyrolytic Chemical Reactions

Approximate Analytical Solutions for Temperature Based Transient Mass Flux and Ignition Time of a Translucent Solid at High Radiant Heat Flux Considering In-Depth Absorption

Extinction of Surface Stabilized Gaseous Diffusion Flames: Part I Simplified Numerical Model and Implications for Solid Fuels in Fires

Numerical Simulation of Coupled Pyrolysis and Combustion Reactions with Directly Measured Fire Properties

Effects of Transient Pyrolysis on Wind-Assisted and Upward Flame Spread

Analytical Prediction of Pyrolysis and Ignition Time of Translucent Fuel Considering Both Time-Dependent Heat Flux and In-Depth Absorption