Abstract:Emerging organic solar cells based on a ternary strategy is one of the most effective methods for improving the blend film morphology, absorption ability, and device performances. On the other hand, this strategy has had very limited success in all-polymer solar cells (all-PSCs) because of the scarcity of new polymers and the challenges faced during third component optimization. Herein, highly efficient ternary all-PSCs were developed from siloxane-functionalized side chains with a wide-band-gap (Eg) polymer, Si-BDT, which is blended with a medium and ultra-narrow Eg polymer donor and acceptor, PTB7-Th, and DCNBT-TPIC. An impressive power conversion efficiency (PCE) of 13.45% was achieved in the ternary all-PSCs [PTB7-Th(0.6):Si-BDT(0.4):DCNBT-TPIC(0.6)] with the addition of 0.4 wt equivalent Si-BDT into binary all-PSCs [PTB7-Th(1):DCNBT-TPIC(0.6) PCE of 10.11%]. In contrast, the binary all-PSCs with a Si-BDT(1):DCNBT-TPIC(0.6) active layer only exhibited a good PCE of 9.92%. More importantly, the siloxane-functionalized side chains increase the light-absorption ability, carrier mobility, blend miscibility, and film morphology in ternary devices compared to those of the binary devices. Hence, exciton dissociation, charge carrier transport, and suppressed recombination properties were facilitated. In the presence of Si-BDT, both binary and ternary all-PSCs PCEs are significantly improved. Indeed, 13.45% PCE is one of the best values reported for all-PSCs except for those based on polymerized small molecule acceptors. In addition, the ternary all-PSCs showed excellent environmental and thermal stabilities with 95 and 84% of the initial PCE retained after 900 and 500 h, respectively. These results offer effective device engineering, providing a new avenue for improving the device performance in ternary all-PSCs.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c20542.Additional text describing experimental details (materials and measurements and characterization of the all-PSCs), SCLC, UV–vis absorption spectra, UPS analysis, efficiency histograms, J–V curves, PL spectra, EDS element mapping, contact angle, GIXRD study, and recent publications based on ternary all-PSCs (PDF)This article has not yet been cited by other publications.

Crystallinity and Phase Separation Induced Morphological Modulation for Efficient Ternary All-Polymer Solar Cells

Rational Design of Ternary-Phase Polymer Solar Cells by Controlling Polymer Phase Separation

Morphology Optimization of the Photoactive Layer Through Crystallinity and Miscibility Regulation for High‐performance Polymer Solar Cells

Fine-Tuned Morphology Based on Two Well-Miscible Polymer Donors Enables Higher Open-Circuit Voltage and Enhanced Stability for Highly Efficient Ternary All-Polymer Solar Cells

Efficient Non-Halogenated Solvent Processed Ternary All-Polymer Solar Cells with A Favorable Morphology Enabled by Two Well-Compatible Donors.

Regulating Phase Separation Kinetics for High‐efficiency and Mechanically Robust All‐Polymer Solar Cells

High‐Performance Green Solvent Processed Ternary Blended All‐Polymer Solar Cells Enabled by Complementary Absorption and Improved Morphology

Morphology Study on Ternary Blend Polymer Solar Cell to Achieve Improved Device Performance

Optimizing the Morphology of All-Polymer Solar Cells for Enhanced Photovoltaic Performance and Thermal Stability

Modulating the Morphology and Molecular Arrangement Via the Well-Compatible Polymer Donor in Multiple Working Mechanisms Interwined Ternary Organic Solar Cells

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Efficient Ternary Polymer Solar Cells with Tunable Crystallinity and Phase Separation of Active Layers Via Incorporating GHK-Cu

Conquering the Morphology Barrier of Ternary All-Polymer Solar Cells by Designing Random Terpolymer for Constructing Efficient Binary All-Polymer Solar Cells

Status and Prospects of Ternary All-Polymer Organic Solar Cells

Ternary All‐Polymer Solar Cells with Efficiency up to 18.14% Employing a Two‐Step Sequential Deposition

Ternary Solar Cells Via Ternary Polymer Donors and Third Component PC71BM to Optimize Morphology with 13.15% Efficiency

Combining Energy Transfer and Optimized Morphology for Highly Efficient Ternary Polymer Solar Cells

Terpolymer Strategy Toward High-Efficiency Polymer Solar Cells: Integrating Symmetric Benzodithiophene and Asymmetrical Thieno[2,3-f]benzofuran Segments

Significantly Enhanced Molecular Stacking in Ternary Bulk Heterojunctions Enabled by an Appropriate Side Group on Donor Polymer

Simultaneously Enhanced Efficiency and Mechanical Durability in Ternary Solar Cells Enabled by Low‐Cost Incompletely Separated Fullerenes

Facile Strategy for Third Component Optimization in Wide-Band-Gap π-Conjugated Polymer Donor-Based Efficient Ternary All-Polymer Solar Cells