Abstract:This Ph.D. research is based on the development of novel sol-gel techniques for synthesis of nanostructured ultra high temperature ceramics (UHTCs) and subsequent spark plasma sintering (SPS) for densifying the UHTC composites. The liquid nature of the sol-gel process offers advantages such as high purity and ability for mixing and infiltration, and thus it can overcome some shortcomings of the conventional power processing of ceramics. SPS delivers microstructures with good density and fine grain size due to its internal heat generation, high heating rate and short sintering time required. Titanium carbide (TiC) and zirconium diboride (ZrB₂) are selected as the UHTC matrix materials to form composites with different kinds of carbon based materials, including 1D carbon nanotubes (CNTs), 1D chopped carbon fibers, 2D woven and 3D needle-punched carbon fiber fabrics, and 3D graphene networks. One challenge to form the composites by conventional powder processing is the difficulty to achieve a homogeneous mix of ceramic powders and the carbon materials. The aim of this research is to take the advantages of sol-gel processing to synthesize nanostructured carbon reinforced UHTC composites with improved microstructures, mechanical and/or other properties. Graphene/TiC composites were synthesized through sol-gel infiltration of graphene network sponges. The C/Ti ratio of the sol-gel solutions influenced the composition as well as the microstructure of the composites. Graphene sheets could react with titanium dioxide (TiO₂) during the carbothermal reduction, forming a plate-like structure when the carbon content in the sol was low. The samples after SPS sintering showed interesting microstructures of nanostructured TiC surrounded by a network of graphene sheets. The composites were toughened by debonding and bridging of the graphene sheets. It was also proved that the composites exhibited an energy absorption mechanism under impact. CNT/TiC composites were prepared by sol-gel mixing and SPS sintering. The application of sol-gel gave an advantage in homogenous mixing. CNTs were able to toughen the composite by bridging, pullout and crack deflection. The fracture toughness increased with the amount of CNTs, but sacrificing the hardness of the materials. A CNTs containing TiC based sol was coated on ZrB₂ raw powders, forming a homogeneous microstructures after sintering, where most of the TiC grains and CNTs were distributed at the grain boundaries of ZrB₂, forming weak interfaces, which benefited the toughness through crack deflection and impact absorption. The chopped carbon fibers had similar toughening effect to CNTs in the composites. Different types of coatings on the surface of carbon fibers influenced the interface properties between ceramic matrix and fibers, thus affecting the fiber pullout and debonding. Sol-gel infiltration was applied to synthesize ceramic composites with 2D woven and 3D needle-punched carbon fiber fabrics. The results showed that sol-gel infiltration was a much more effective way to uniformly fill the fine pores between fiber filaments than the conventional powder slurry infiltration method. The composites showed improved fracture toughness as a result of fiber pullout, debonding, and crack deflection.

Sugar-Derived Nanocrystalline Graphite Matrix C/C Composites with Excellent Ablative Resistance at 3000 °C

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Preparation and Properties of C/SiC Composites Reinforced by High Thermal Conductivity Graphite Films

Enhanced strength and toughness of SiC/C composite ceramics via SiC@graphene core–shell nanoparticles

Polyarylacetylene As a Novel Graphitizable Precursor for Fabricating High-Density C/C Composite Via Ultra-High Pressure Impregnation and Carbonization

Preparation and properties of the three-dimensional highly thermal conductive carbon/carbon-silicon carbide composite using the mesophase-pitch-based carbon fibers and pyrocarbon as thermal diffusion channels

Si3N4 nanowires@pyrolytic carbon nanolayers coupled with hydroxyapatite nanosheets as reinforcement for carbon matrix composites with boosting mechanical and friction properties

Fabrication of Large Aerogel-Like Carbon/Carbon Composites with Excellent Load-Bearing Capacity and Thermal-Insulating Performance at 1800 °C

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Ablation behaviour of Csf/ZrB2-SiC composites fabricated by direct ink writing and reactive melt infiltration

Sol-gel synthesis of carbon based materials reinforced ultra high temperature ceramic composites

Eco-Friendly Preparation of Carbon-Bonded Carbon Fiber Based on Glucose-Polyacrylamide Hydrogel Derived Carbon as Binder

Study on the ablation performance of SiC-coated high thermal conductivity three-dimensional C/C composites

Sugar‐derived Isotropic Nanoscale Polycrystalline Graphite Capable of Considerable Plastic Deformation

Microstructure, Mechanical and Ablation Properties of Transpiration Cooling Applied to C/C-SiC Composite for Novel Anti-ablation Material

Improving thermal shock and ablation resistance of high thermal conductivity carbon/carbon composites by introducing carbon nanotubes

Design, Preparation and Properties of Carbon Fiber Reinforced Ultra-High Temperature Ceramic Composites for Aerospace Applications: A Review

Multifunctional Thermal Barrier Application Composite with SiC Nanowires Enhanced Structural Health Monitoring Sensitivity and Interface Performance.

SiC–Si3N4 composite with multi-laminate nanowires originated from oriented porous structure by freeze-casting

Flexible SiC/Si3N4 Composite Nanofibers with in Situ Embedded Graphite for Highly Efficient Electromagnetic Wave Absorption

Starting from essence to reveal the ablation behavior and mechanism of 3D PyC Cf/ZrC-SiC composite