Abstract:The Fe‐Mn alloys are potential candidates for biodegradable implant applications. However, the very low degradation rates of Fe‐Mn alloys in the physiological environment are a major disadvantage. In this study, the degradation rate of a Fe‐20Mn alloy was improved using the groove pressing (GP) technique. Hot rolled sheets of 2 mm thickness were subjected to GP operation at 1000°C. Uniform fine‐grained (UFG) Fe‐Mn alloys were obtained using the GP technique. The influence of GP on the microstructure, mechanical properties, degradation behavior in simulated body fluid (SBF), surface wettability, biomineralization, and cytocompatibility was investigated and compared to the annealed (A Fe‐Mn) and rolled (R Fe‐Mn) sample. The groove‐pressed Fe‐Mn (G Fe‐Mn) alloy had a grain size of approximately 40 ± 16 μm whereas the A Fe‐Mn and R Fe‐Mn samples had grain sizes of 303 ± 81 and 117 ± 14.5 μm, respectively. Enhanced strength and elongation were also observed with the G Fe‐Mn sample. The potentiodynamic polarization test showed the highest Icorr, lowest polarization resistance, and lowest Ecorr for the G Fe‐Mn sample among all other samples indicating its higher degradation rate. The weight loss data from immersion tests also shows that the percentage of weight loss increases with time indicating the accelerated degradation behavior of the sample. The static immersion test showed an enhancement in weight loss of 0.46 ± 0.02% and 1.02 ± 0.05% for R Fe‐Mn and G Fe‐Mn samples, respectively, than A Fe‐Mn sample (0.31 ± 0.03%) after 56 days in immersion in SBF. The greater biomineralization tendency in UFG materials is confirmed by the G Fe‐Mn sample's stronger hydroxyapatite deposition. When compared to the A Fe‐Mn and R Fe‐Mn samples, the G Fe‐Mn sample has a better wettability, which promotes higher cell adhesion and vitality, showing higher biocompatibility. This study demonstrates that Fe‐20Mn processed by GP has potential applications for the manufacture of biodegradable metallic implants.

Magnetic Energy Drives Mass Transfer Processes to Accelerate the Degradation of Fe-based Implant

Galvanic Corrosion Induced by Heterogeneous Bimodal Grain Structures in Fe-Mn Implant

Stress-Induced Dual-Phase Structure to Accelerate Degradation of the Fe Implant

Hydrolytic Expansion Induces Corrosion Propagation for Increased Fe Biodegradation.

Predicting the Degradation Behavior of Magnesium Alloys with a Diffusion-Based Theoretical Model and in Vitro Corrosion Testing

Construction of Fe/Ag Galvanic Couple by Mechanochemical In-Situ Reduced Ag to Accelerate the Degradation of Fe-based Implant

Mechanically Driving Supersaturated Fe–Mg Solid Solution for Bone Implant: Preparation, Solubility and Degradation

Mesoporous Carbon as Galvanic-Corrosion Activator Accelerates Fe Degradation

Study of the effect of magnetic fields on static degradation of Fe and Fe-12Mn-1.2C in balanced salts modified Hanks' solution

Enhancing the degradation rate and biomineralization nature of antiferromagnetic Fe‐20Mn alloy by groove pressing

Fe-Zn supersaturated solid solution prepared by mechanical alloying and laser sintering to accelerate degradation

Corrosion Behavior in Magnesium-Based Alloys for Biomedical Applications

Research progress on corrosion behaviors and biocompatibility of rare-earth magnesium alloys in vivo and in vitro

Effect of a High-Voltage Pulsed Magnetic Field on Microstructure, Mechanical Properties and Corrosion Behavior of As-Cast Biodegradable Zn-Al Alloy

In Vitro Corrosion and Cytocompatibility of A Microarc Oxidation Coating and Poly(L-Lactic Acid) Composite Coating on Mg-1li-1ca Alloy for Orthopedic Implants

Study on the effect of magnetic needle grinding process on the service properties of medical Mg-1.6Ca-2.0Zn alloy

Magnetostrictive improvement in Er-doped biodegradable Fe81Ga19 alloys manufactured by selective laser melting

Self-catalytic Degradation of Iron-Bearing Chemical Conversion Coating on Magnesium Alloys — Influence of Fe Content

Surface Engineering of Biodegradable Magnesium Alloys for Enhanced Orthopedic Implants.

Effect of PLGA+MAO composite coating on the degradation of magnesium alloy in vivo and in vitro

Supersaturated Solid Solution of Mg in Fe Produced by Mechanical Alloying Followed by Selective Laser Melting (SLM) to Accelerate Degradation for Biomedical Applications