Abstract:Here we report an optical fiber sensor capable of performing strain-insensitive simultaneous measurement of bending and temperature using a long-period fiber grating (LPFG) inscribed on doubleclad fiber (DCF) with a CO₂ laser at ˜10.6 μm. The LPFG inscribed on DCF, referred to as a DC-LPFG, was fabricated by scanning CO₂ laser pulses on an unjacketed DCF with a specific period. Due to co-directional mode coupling, the fabricated DC-LPFG has discrete attenuation bands widely distributed over hundreds of nanometers. Among these wavelength-dependent loss dips, adjacent two dips with different resonance wavelengths were selected as sensor indicators for the measurement of bending and temperature. For these two indicator dips designated as dips A and B, their bending and temperature responses were investigated in a curvature range of 4.90 to 21.91 m-1 and a temperature range of 30 to 110 °C. With increasing bending applied to the DC-LPFG at room temperature, dips A and B showed different blue shifts. The bending sensitivities of dips A and B were measured to be approximately -0.77 and 0.51 nm/m-1, respectively. Unlike the bending response, they showed red shifts of different amounts with increasing ambient temperature, while the sensor head (i.e., the DC-LPFG) remained straight without any applied bending. The temperature sensitivities of dips A and B were measured to be ˜0.094 and ˜0.078 nm/°C, respectively. Owing to their linear and independent responses to bending and temperature, bending and temperature changes applied to the DC-LPFG could be simultaneously estimated from the measured wavelength shifts of the two indicator dips using their pre-determined bending and temperature sensitivities. Moreover, in a strain range of 0 to 2200 με (step: 200 με), strain-induced spectral variations of dips A and B were also measured, and the strain sensitivities of dips A and B were evaluated as approximately -0.028 and -0.013 pm/με, respectively. These strain-induced wavelength shifts were so small that they had little effect on the measurement results of bending and temperature. Thus, it is concluded that the fabricated DC-LPFG can be employed as a cost-effective sensor head for strain-insensitive separate measurement of bending and temperature.

Curvature Sensor Based on D-shape Fiber Long Period Fiber Grating Inscribed and Polished by CO2 Laser

Integrated All-Fiber Sensor for Simultaneous Measurements of Curvature and Temperature

Vector Curvature Sensor Based on Asymmetrically Polished Long-Period Fiber Grating

Simultaneous Measurement of Curvature Vector and Temperature Based on Composite Gratings Inscribed on D-Shaped Fiber

A Wide Range Curvature Sensor Based on Fiber Ring Laser With a Long-Period Fiber Grating

A Simultaneous Measurement Sensor for Temperature and Curvature Based on Congruent Quasi-Helical Long-Period Fiber Grating

Angularly Cascaded Long-Period Fiber Grating for Curvature and Temperature Detection

A Novel Long Period Fiber Grating Sensor Measuring Curvature and Determining Bend-Direction Simultaneously

All-fiber Sensor Based on Few-Mode Fiber Offset Splicing Structure Cascaded with Long-Period Fiber Grating for Curvature and Acoustic Measurement

Miniature Temperature-Independent Curvature Sensor Based on a Phase-Shifted Long-Period Fiber Grating Using Deep Tapering

Bend Vector Sensor Based on Long Period Fiber Grating Inscribed in Mismatched Twin Core Fiber

Simultaneous Measurement of Curvature and Temperature Based on Thin Core Ultra-Long Period Fiber Grating

Long Period Fiber Grating Sensors Measuring Bend-curvature and Determining Bend-direction Simultaneously

Simultaneous Measurement of Refractive Index and Curvature Based on Capillary Fiber with Structural Long-Period Gratings

Curvature and Temperature Measurement Based on a Few-Mode PCF Formed M-Z-I and an Embedded FBG.

Large Range Curvature Measurement Using FBGs in Two-Core Fiber with Protective Coating

Multiparameter Sensor Based on Long-Period Grating in Few-Mode Ring-Core Fiber for Vector Curvature and Torsion Measurement

Strain-Insensitive Simultaneous Measurement of Bending and Temperature Using Long-Period Fiber Grating Inscribed on Double-Clad Fiber with CO₂ Laser

Curvature and angle sensor based on LP 21 mode reflected by a four-mode fiber Bragg grating

High Sensitivity Strain Sensor Based on Curved LPG Fabricated in Eccentric Hollow-Core Fiber

Highly Sensitive Two-Axis Bending Sensor Based on Arc-Induced Long Period Fiber Grating in Dual Side-Hole Fiber