Abstract:As a new laser surface treatment technology, laser shock peening (LSP) has been applied to strengthen and prolong the life of critical components such as the aero-engine and gearbox. Ensuring the consistency and stability of LSP processing quality is of great significance to the long service life of the aviation mentioned above equipment. However, the protective coating is easily ablated and damaged in the high-energy transient LSP process, limiting the industrial application of LSP significantly. Therefore, this paper proposed a real-time detection method for protective coating damage of LSP based on ReliefF feature weight fusion by analyzing laser-induced plasma spectrum signal. The 7075 aluminum alloy with a thickness of 4 mm was used as an LSP target, and the black tape was used as the protective coating. Firstly, the Ocean Optics-HR4000 spectrometer with a wide wavelength range and Princeton SP2750 spectrometer with a high resolution was used to synchronously collect the plasma spectra produced in the LSP transient process. Secondly, according to the spectral signals with a high resolution collected by the Princeton SP2750 spectrometer, the peak intensities and Stark-FWHMs of Al I spectra at 394. 40 and 396. 15 nm and that of Fe I spectra at 393. 36 and 396. 80 nm were extracted, then, combined with the feature importance obtained by the ReliefF algorithm to screen out two Al I spectra that were more sensitive to the damage states of the protective coating, andqualitatively analyzedthe sensitivity and the law of transient variation for intensity and Stark-FWHM of Al I spectra to the damage states of the protective coating. Furthermore, a feature named intensity-FWHM (I-FWHM) fusing the information of multiple spectral emission lines was constructed using the ReliefF algorithm, and then, the ability of each feature to distinguish the three kinds of damage states was quantitatively evaluated based on the distance between classes. Finally, combined with the threshold segmentation method, real-time detection of LSP protection layer damage was realized. The experimental results show that the intensity is very poor in distinguishing between normal state and slight damage but very strong in distinguishing between slight damage and complete damage. The Stark-FWHM is far better than intensity in distinguishing between the normal state and slight damage, but the abilityis relatively weak in distinguishing between slight and complete damage. The I-FWHM combines the advantages of the above single feature and can better distinguish the three types of damage states simultaneously. Therefore, I-FWHM has stronger anti-interference ability and higher robustness for the real-time detection of protective coating damage state in the LSP process.

Real-Time Detection of Protective Coating Damage During Laser Shock Peening Based on ReliefF Feature Weight Fusion

INTEGRATED TECHNOLOGY FOR DETECTION AND REPAIR OF MECHANICAL COMPONENT SURFACE FATIGUE MICROCRACKS USING PULSED LASER

Detection and Quantification of Damage in Metallic Structures by Laser-Generated Ultrasonics

Rebalancing Mel-frequency Cepstrum and Parallel Fusion Model for Surface Hardness Monitoring of Laser Shock Peening Using Acoustic Emission

Monitoring and On-Line Quality Evaluation in Laser Shock Peening Process:Current Status and Challenges

Effects of Residual Stress Induced by Laser Shock Peening on Mixed-Mode Crack Propagation Behavior in 7075-T6 Aluminum Alloy Panel

Research on the Residual Stress Induced by Square-Spot Laser Shock Peening on 2024-T351 Specimens

Online Evaluation of Surface Hardness for Aluminum Alloy in LSP Using Modal Acoustic Emission

Surface Hardness Monitoring of Laser Shock Peening: Acoustic Emission and Key Frame Selection

Deep learning-based monitoring of surface residual stress and efficient sensing of AE for laser shock peening

Simulation of the elasto-plastic response and residual stresses near metal surface due to laser shock processing

On-line evaluation and monitoring technology for material surface integrity in laser shock peening - A review

A Novel Approach for Surface Integrity Monitoring in High-Energy Nanosecond-Pulse Laser Shock Peening: Acoustic Emission and Hybrid-Attention CNN.

Automatic Detection of Laser Damage Threshold by Scattering Light Technique

Finite Element Simulation of the Film Spallation Process Induced by the Pulsed Laser Peening

The Influence of Absorbing Coating Material on the Efficiency of Laser Shock Peening

Over Peening Effect of Al7050 Mid-thick Plates with Continued Multiple Laser Shock Peening Impacts at the Same Position

Microstructure and Fatigue Performance of Hard Al Alloy Repaired by Supersonic Laser Deposition with Laser Shock Peening Treatment

Laser shock peening regulating aluminum alloy surface residual stresses for enhancing the mechanical properties: Roles of shock number and energy

The effect of laser shock peening on surface integrity and high and very high cycle fatigue properties of 2024-T351 aluminum alloy

Laser shock processing with two different laser sources on 2050‐T8 aluminum alloy