Abstract:Aluminizing is a diffusion based chemical surface treatment on materials to provide excellent protection against high temperature oxidation and corrosion, but is likely to be accompanied by a degradation in mechanical properties. Laser shock peening (LSP) is a superior laser based surface strengthening technique for enhanced mechanical properties. In this study, we focus on combining these two methods on the AISI 321 stainless steel to introduce both chemical and structural gradients for superior properties. Comparative investigation on both the microstructure and mechanical properties of the as received 321 steel, aluminized 321 steel and the aluminizing + LSP processed steel indicated that: (1) A three-layer protective coating was introduced on the surface of the aluminized steel and the concentration of Al decreased gradually from the outermost layer to a certain depth, forming B2-FeAl(Cr) solid solution and Al 2 O 3 in Layer-I, B2-FeAl and DO 3 -Fe 3 Al phases in Layer-II and BCC-Fe(Cr,Al) solid solution phase in Layer-III, with B2-NiAl precipitates distributed in Layer-II and Layer-III. (2) After LSP treatment, a dislocation density gradient from the surface to the matrix, dislocation-precipitate interactions and a significant compressive stress were introduced. (3) Though the aluminized steel exhibited a decrease in the high temperature tensile properties compared to that of the as received 321 steel, the aluminizing + LSP processed steel achieved a striking enhancement. The formation of three-layer coating, dislocation density gradient, dislocation-precipitate interactions and the residual stress contribute jointly to gain the yield strength, ultimate strength and fracture elongation up to 265 MPa, 430 MPa and 37.5 % at 620 °C, respectively.

Improved Creep-Fatigue and Remnant Tensile/creep Properties of 321 Stainless Steel by Self-Healing Coating

Remnant tensile and creep properties of aluminized AISI 321 austenite stainless steel under prior creep–fatigue interaction

Experimental and modeling investigation of the thermal shock behavior of TiC-based self-healing coatings on AISI 321 stainless steel

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

Influence of prior creep-fatigue exposure on remnant tensile and creep properties of AISI 321 austenite stainless steel

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Creep-fatigue interactive behavior and damage mechanism of TP321 stainless steel under hybrid-controlled conditions

Improved corrosion resistance of AISI 321 steel to molten Al-Si alloy by aluminizing and laser shock peening

Introducing both chemical and structural gradients in AISI 321 stainless steel via aluminizing and laser shock peening for superior properties

Microstructure and tensile properties of AISI 321 stainless steel with aluminizing and annealing treatment

Coating-assisted deterioration mechanism of creep resistance at a nickel-based single-crystal superalloy

Tribological properties of self-healing NiCrAlY/Cr3C2-Ti3AlC2 coating at high temperatures

Fretting wear resistance at ambient and elevated temperatures of 316 stainless steel improved by laser cladding with Co-based alloy/WC/CaF 2 composite coating

A novel approach to coating for improving the comprehensive high-temperature service performance of TiAl alloys

High-Temperature Wear Behavior and Mechanisms of Self-Healing NiCrAlY-Cr3C2-Ti2SnC Coating Prepared by Atmospheric Plasma Spraying

Strengthening Of An Al-Containing Austenitic Stainless Steel At High Temperature

Revealing the wear mechanism of NiTi alloy coatings with biomimetic sandwich structures by laser cladding

Deformation and Annealing Behavior of Cr Coating Prepared by Pack-Cementation on the Surface of Austenitic Stainless Steel

The pre-corrosion fatigue behavior of 321 steel coated by laser additively manufactured FeCoNiCrMn high-entropy alloy

Superior Creep Resistance and Remnant Strength of Novel Tempered Ferritic-Martensitic Steels Designed by Element Addition

Beneficial role of short-term aging on creep performance of cold-worked Ti-added 14Cr–15Ni stainless steel