Abstract:This paper presents a level-crossing successive-approximation-register (LC-SAR) hybrid analog-to-digital converter (ADC) that combines an LC ADC with an SAR ADC, which may be used for Internet of Things (IoT) random sparse event scenarios. The sampling frequency of a traditional LC ADC is usually proportional to the maximum instantaneous rate of change of the input signal; therefore, a higher input signal frequency inevitably leads to higher system power consumption. However, the proposed hybrid ADC uses the input level difference between the two moments before and after level-crossing detection, thereby ensuring a higher conversion precision and lower power consumption, even at higher input signal frequencies. Compared with traditional LC ADC or SAR ADC, the proposed hybrid ADC combines the ultralow-power advantage of LC ADC with the high-precision advantage of SAR ADC in converting IoT data with sparse characteristics such as ECG, EEG, and brain potential. The LC-SAR hybrid ADC is designed with a 0.18 μm CMOS process and consumes 4.34 μW at a 1.8 V supply voltage, achieving an SNDR of 67.41 dB and a bandwidth of 20 kHz. The spectrum analysis result was 10.85 ENOB when the input sinusoidal signal was 14.975 kHz. When inputted with an ECG signal, the system power consumption was as low as 0.49 μW. Furthermore, the proposed hybrid ADC obtained a good figure of merit, with FoMw and FoMs reaching 58.8 fJ/conv.steps and 164 dB, respectively. Compared to a conventional uniform sampling ADC, approximately 80% of the power savings and an 8x compression ratio can be achieved in physiological signal acquisition applications.

A 66.67kHz 4.953 nJ/Conv-Step 5b Fully Integrated Asynchronous SAR ADC Using <tex>$\mathbf{4} \boldsymbol{\mu}\mathbf{m}$</tex> LTPS TFTs

A 16-Bit 2.5-Ms/s SAR ADC with On-Chip Foreground Calibration

A 10-Bit 250-KS/s 1.24-uW SAR ADC for IoT Sensors with Energy-Efficient Comparator.

A BJT-based SAR Temperature Sensor with a 5.12 pJ.K-2 Resolution FoM from-40 degrees C to 125 degrees C

A BJT-based SAR Temperature Sensor with a $5.12\ \text{pJ}\cdot \mathrm{K}^{2}$ Resolution FoM from -40 °C to 125 °C.

Flexible and fully integrated 4-bit SAR ADC Using Metal-Oxide TFTs

A 0.024 Mm<sup>2</sup> 4.9 Fj 10-Bit 2 MS/s SAR ADC in 65 Nm CMOS

A 6.94-Fj/conversion-step 12-Bit 100-Ms/s Asynchronous SAR ADC Exploiting Split-CDAC in 65-Nm CMOS

A 68.5 Db-Sndr, 12.4-Fj/conv.-step, 100-Ms/s Pipelined-Sar ADC with PVT-enhanced Circuitry

A 68.36 dB 12 bit 100MS/s SAR ADC with a low-noise comparator in 14-nm CMOS FinFet

A 0.49–4.34 μW LC-SAR Hybrid ADC with a 10.85-Bit ENOB and 20 KS/s Bandwidth

A 1.5fJ/conv-step 10b 100kS/s SAR ADC with gain-boosted dynamic comparator

A 0.95-Mw 6-B 700-Ms/s Single-Channel Loop-Unrolled SAR ADC in 40-Nm CMOS

A 25-Gs/s 6-Bit Time-Interleaved SAR ADC with Design-for-test Memory in 40-Nm Low-Leakage CMOS

A 12-bit, 100 kS/s, PVT robust SAR ADC in 65 nm CMOS process

A single channel, 6-bit 410-ms/s asynchronous SAR ADC based on 3bits/stage

A 16-bit 18-MSPS flash-assisted SAR ADC with hybrid synchronous and asynchronous control logic

A 12.9-ENOB 50.6 Fj/conv.step Time-Amplitude Aligned Level-Crossing SAR ADC

A 455 Nw 220 Fj/conversion-Step 12 Bits 2 Ks/s SAR ADC for Portable Biopotential Acquisition Systems

A 62.2db SNDR Event-Driven Level-Crossing ADC with SAR-Assisted Delay Compensation Loop for Time-Sparse Biomedical Signal Acquisition.

Design of a 0.005mm 2 8.5enob 14.9 Fj/conv-Step SAR ADC for Biomedical Application