Abstract:In this study, three different levels of laser energy inputs (Ev) were used for selective laser melting of Ti-5Al-2.5Sn alloy and the as-deposited tensile properties along the vertical direction with respect to deposition layers were found to be statistically identical to those along the horizontal direction for all the samples. Densification states, microstructures, and crystallographic orientation characteristics of the different samples, as well as their contributions to the isotropic properties were researched. The results first indicated that near spherical pores would form at the relatively high Ev (208 J/mm(3)) whereas lack-of-fusion defects would generate at the relatively low Ev (51 J/mm(3)). When the moderate Ev (167 J/mm(3)) was used, samples with very few defects could be fabricated. Then, it was seen that samples built at 51 and 167 J/mm(3) presented a martensite (alpha')-dominated microstructure in which the boundaries of columnar prior-beta were decorated by grain-boundary alpha (alpha(GB)). When Ev increased to 208 J/mm(3), a duplex microstructure composed of alpha' and massive alpha (alpha(M)) would form within prior-beta matrix of the as-deposited samples. An overall increasing trend in prior-beta's width with the increase of Ev was also identified. Afterwards, it was proved that there was no strong texture within all the samples and this was one cause of the isotropic properties. Besides, for samples built at 51 J/mm(3), the negative influence of lack-of-fusion on vertical properties cooperated with the adverse effect of large quantities of a GB on horizontal properties, promoting the obtainment of isotropic properties. For samples built at 167 J/mm(3), not only the high densification degree but also the significantly increase in prior-beta's width and the resultant decrease in alpha(GB) 's content helped to eliminate significant anisotropy. For samples built at 208 J/mm(3), both the near spherical pores which resulted in near-identical bearing areas on different sections and the absent of alpha(GB) contributed to the isotropic properties. This paper can provide some basis for the laser additive manufacturing of titanium products with isotropic properties.

Unraveling the Inherent Anisotropic Properties of in Situ Alloyed Copper-Modified Titanium Alloys Produced by Laser Powder Bed Fusion

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Enhanced strength-ductility synergy and mechanisms of heterostructured Ti6Al4V-Cu alloys produced by laser powder bed fusion

Effects of the process parameters on the formability and properties of Ni54(at.%) Ti alloys prepared by laser powder bed fusion

The effect of build orientations on mechanical and thermal properties on CuCrZr alloys fabricated by laser powder bed fusion

Innovative Fabrication Design for In Situ Martensite Decomposition and Enhanced Mechanical Properties in Laser Powder Bed Fused Ti6Al4V Alloy

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

The effects of specimens geometry on solidification conditions and microstructure formation in laser powder bed fusion fabricated Ti–6Al–4V alloys

Microstructure Tailoring for High Strength Ti-6Al-4V without Alloying Elements through Optimized Preheating and Post-Heating Laser Scanning in Laser Powder Bed Fusion

Effect of Sample‐Build Orientation on the Tensile Deformation and Properties of Ti6Al4V Processed by Laser Powder Bed Fusion

Achieving superior strength-ductility combination in the heterogeneous microstructured Ti64 alloy via multi-eutectoid elements alloying with CoCrFeNiMn during laser powder bed fusion

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

Additive manufacturing of high strength copper alloy with heterogeneous grain structure through laser powder bed fusion

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion

Anisotropic material properties of pure copper with fine-grained microstructure fabricated by laser powder bed fusion process

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Effect of processing parameters on the defects, microstructure, and property evaluation of Ti-6Al-4V titanium alloy processed by laser powder bed fusion

In Situ Microstructure Modification Using a Layerwise Surface-Preheating Laser Scan of Ti-6Al-4V during Laser Powder Bed Fusion

Synchrotron Characterisation of Ultra-Fine Grain TiB2/Al-Cu Composite Fabricated by Laser Powder Bed Fusion

Selective Laser Melting of Ti-5Al-2.5Sn Alloy with Isotropic Tensile Properties: the Combined Effect of Densification State, Microstructural Morphology, and Crystallographic Orientation Characteristics