Abstract:Thermoelectric materials with high average power factor and thermoelectric figure of merit (ZT) has been a sought-after goal. Here, we report new n-type thermoelectric system CuxPbSe0.99Te0.01 (x = 0.0025, 0.004, and 0.005) exhibiting record-high average ZT ∼ 1.3 over 400–773 K ever reported for n-type polycrystalline materials including the state-of-the-art PbTe. We concurrently alloy Te to the PbSe lattice and introduce excess Cu to its interstitial voids. Their resulting strong attraction facilitates charge transfer from Cu atoms to the crystal matrix significantly. It follows the increased carrier concentration without damaging its mobility and the consequently improved electrical conductivity. This interaction also increases effective mass of electron in the conduction band according to DFT calculations, thereby raising the magnitude of Seebeck coefficient without diminishing electrical conductivity. Resultantly, Cu0.005PbSe0.99Te0.01 attains an exceptionally high average power factor of ∼27 μW cm–1 K–2 from 400 to 773 K with a maximum of ∼30 μW cm–1 K–2 at 300 K, the highest among all n- and p-type PbSe-based materials. Its ∼23 μW cm–1 K–2 at 773 K is even higher than ∼21 μW cm–1 K–2 of the state-of-the-art n-type PbTe. Interstitial Cu atoms induce the formation of coherent nanostructures. They are highly mobile, displacing Pb atoms from the ideal octahedral center and severely distorting the local microstructure. This significantly depresses lattice thermal conductivity to ∼0.2 Wm–1 K–1 at 773 K below the theoretical lower bound. The multiple effects of the dual incorporation of Cu and Te synergistically boosts a ZT of Cu0.005PbSe0.99Te0.01 to ∼1.7 at 773 K.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/jacs.0c07712?goto=supporting-info">https://pubs.acs.org/doi/10.1021/jacs.0c07712</a>.Details in theoretical calculations, additional APT results, and thermoelectric properties (<a class="ext-link" href="/doi/suppl/10.1021/jacs.0c07712/suppl_file/ja0c07712_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Engineering an Atomic-Level Crystal Lattice and Electronic Band Structure for an Extraordinarily High Average Thermoelectric Figure of Merit in N-Type PbSe

Engineering atomic-level crystal lattice and electronic band structure for extraordinarily high average thermoelectric figure of merit in n-type PbSe

Atomic Level Defect Structure Engineering for Unusually High Average Thermoelectric Figure of Merit in N‐type PbSe Rivalling PbTe

Exceptionally High Average Power Factor and Thermoelectric Figure of Merit in n-type PbSe by the Dual Incorporation of Cu and Te

High ZT 2D Thermoelectrics by Design: Strong Interlayer Vibration and Complete Band‐Extrema Alignment

Realizing Ultrahigh Thermoelectric Performance in n‐Type PbSe Through Lattice Planification and Introducing Liquid‐Like Cu Ions

Pseudo‐Nanostructuring and Grain Refinement Enhance the Near‐Room‐Temperature Thermoelectric Performance in n‐type PbSe

Realizing High Thermoelectric Performance in p-Type SnSe Crystals via Convergence of Multiple Electronic Valence Bands

Realizing High‐Ranged Out‐of‐Plane ZTs in N‐Type SnSe Crystals through Promoting Continuous Phase Transition

Nanoscale defect structures advancing high performance n-type PbSe thermoelectrics

Interstitial Defects Facilitate Dense Dislocations and Band Convergence for High Thermoelectric Performance in SnTe

Point Defect Engineering of High‐Performance Bismuth‐Telluride‐Based Thermoelectric Materials

Band Modulation and Strain Fluctuation for Realizing High Average zT in GeTe

Multiscale structure and band configuration tuning to achieve high thermoelectric properties in n-type PbS bulks

Zn-Induced Defect Complexity for the High Thermoelectric Performance of n-Type PbTe Compounds

Enhanced Thermoelectric Performance of N‐Type PbSe Through Semi‐Coherent Nanostructure by AgCuTe Alloying

Multiple valence bands convergence and strong phonon scattering lead to high thermoelectric performance in p-type PbSe

Rational Electronic and Structural Designs Advance BiCuSeO Thermoelectrics

High Thermoelectric Performance Via Hierarchical Compositionally Alloyed Nanostructures.

Evolution of defect structures leading to high ZT in GeTe-based thermoelectric materials

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4