Abstract:Polyurethane mixtures (PUMs) exhibit excellent road performance and low energy consumption and emissions during construction and are expected to replace asphalt mixes in steel bridge deck paving and snow removal. However, their poor hydrolysis resistance leads to inferior water stability, limiting their applicability. Although researchers have attempted to use polyurethane with a suitable hydrolysis resistance or improve the grading, among other measures, the improvement is limited, and polyurethane can negatively impact other road performance indicators. In this study, polymerized carbodiimide (PCDI) was used to increase the hydrolysis resistance of PUMs. The effect of PCDI doping on the performance of polyurethane was examined through water-absorption, tensile, and contact-angle tests. Additionally, the effects on the high-temperature and low-temperature performance and water stability of the PCDI-doped PUM were investigated. The effects of hydrolysis and plasticization on the road performance of PCDI-doped PUMs were analyzed. The results indicated that the PCDI reduced the water absorption and tensile strength and increased the elongation at break of the polyurethane specimens, whereas it hardly affected the contact angle of the specimens. The recommended dosage of PCDI with regard to performance and economic cost is 1%. The addition of PCDI significantly improved the water stability of the PUM: the residual stability ratio and residual stability increased by 48.0% and 52.1%, respectively, and the tensile-strength ratio and post-freeze–thaw splitting strength increased by 137.5% and 151.2%, respectively, with less effect on the high-temperature and low-temperature performance, indicating that the addition of PCDI is a feasible method for enhancing the water stability of PUMs. The hydrolysis of polyurethane significantly degraded the high-temperature and low-temperature performance and water stability of the PUM. The recovery of the plasticizing effect restored the road performance to a certain extent; however, it was not restored to the state where no hydrolysis occurred.

Experimental Investigation on the Water Stability of Castable High-Capacity Polyurethane Bearing

Synthesis and Application of Hydroxyethyl Methacrylate Modified Waterborne Polyurethane

Facile Fabrication and Tribological Properties of Self-Lubricating Polyurethane Based on Expanded Graphite/Paraffin for Water Lubricated Bearings

A Study on the Preparation and Cavitation Erosion Mechanism of Polyether Polyurethane Coating

Tribological Behavior of Sulfonated Polyether Ether Ketone with Three Different Chemical Structures under Water Lubrication

Ultralow friction of PEEK composites under seawater lubrication

Tribological evaluation of thermoplastic polyurethane-based bearing materials under water lubrication: Effect of load, sliding speed, and temperature

Tribological Performance of Self‐lubricating Polyurethane Elastomer Compounding with the Modified Ultra‐high Molecular Weight Polyethylene

A novel ternary interpenetrating polymer networks based on NBR/PU/EP with outstanding damping and tribological properties for water-lubricated bearings

The investigation of support effect from hard substrate to soft coating of PI/EP-PTFE under different coating thicknesses and frictional contacts

Effects of Water or Alkali Solution Immersion on the Water Uptake and Physicomechanical Properties of Polyurethane

Physical ageing of polyurea elastomers upon water absorption: Molecular dynamics and microphase structures

Preparation, mechanical properties of waterborne polyurethane and crosslinked polyurethane‐acrylate composite

Improvement of Water Stability of Single-Component Polyurethane Mixture

Effects of aminopropyl-terminated polydimethylsiloxane on structure and properties of waterborne polyurethane-acrylate

Aqueous lubrication and surface microstructures of engineering polymer materials (PEEK and PI) when sliding against Si3N4

Experimental Study on Material Properties of Bearing Bush of Water Lubricated Bearing

Effect of Electrostatic Heterocoagulation of PVM/MA Grafted Carbon Black and Attapulgite Nanorods on Electrical and Mechanical Behaviors of Waterborne Polyurethane Nanocomposites

Quantification of Water Diffusion in CMP Pad Polymers and Impact on Mechanical Properties

Experimental Research of Abnormal Wear for Water-Lubricated Polymer Bearings under Low Speed, Heavy Pressure, and High Water Temperature

STRUCTURE AND PROPERTIES OF POLY (Ε-Caprolactone)-based CASTABLE POLYURETHANE ELASTOMERS