Abstract:The effect of post-weld heat treatment on microstructure and mechanical properties of electron beam welded IN738LC joint has been investigated. The fusion zone consists of γ-Ni matrix, bimodal-size γʹ particles, granular MC carbides (Ti-rich) and Cr-rich M23C6 carbide chain in IN738LC joint subjected to post-weld heat treatment. The secondary γʹ particle in fusion zone precipitates and grows ceaselessly with the increased aging time. The coarsening of γʹ particle follows the Lifshiitz-Slyozov-Wagner coarsening theory with a constant coarsening rate of 1.003 × 10−27m3/s. The secondary γʹ particle in base metal shows a similar size with that of fusion zone, but a lower volume fraction (52%) than that of fusion zone (54%). M23C6 carbide is easier to precipitate along high angle grain boundaries. As aging time increases, the morphology of M23C6 carbide changes from discrete granular shape to continuous chain. The thickness of M23C6 carbide also increases dramatically. Owing to smaller grain size and higher solute concentration in fusion zone, more M23C6 carbides form in FZ than that of base metal. With the increased aging time, the tensile strength of IN738LC joint at 900°C decreases gradually, while the elongation of joint firstly increases and then decreases, which is attributed to the increased channel width of γ-Ni matrix. Due to the formation of continuous M23C6 carbide chain, the rupture life of IN738LC joint firstly increases and then decreases as aging time increases. Combined with the mechanical properties and size stability of γʹ precipitates in IN738LC joint, 1125°C/2 h + 850°C/24 h is an optimized post-weld heat treatment regime.

Effect of Chemical Constitution Aliquation of Rail and Heat Treatment on Welded Joint Quality

Microstructural Evolution and Micro-Corrosion Behaviour of Flash-Welded U71Mn Joints as a Function of Post-Weld Heat Treatment

Effect of Alloying Composition on Microstructure and Mechanical Properties of Ultranarrow Gap Welded Joints of U71Mn Rail Steel

Influence of CDFW Process Parameters on Microstructure and Mechanical Properties of U75V Rail Steel Welded Joint

Effect of Normalising Process on the Corrosion Behaviour of U75V Rail Flash Butt Welded Joints in a Marine Environment

Effects of rail flash-butt welding and post-weld heat treatment processes meeting different national standards on residual stresses of welded joints

Study on microstructure and mechanical properties of continuous drive friction-welded joints of bainitic rail steel

Microstructural/mechanical Characterizations of Electron Beam Welded IN738LC Joint after Post-Weld Heat Treatment

Influence of Rail Metallurgy and Welding Parameterization on the Quality of Flash Butt Welds Done with Mobile Equipment

The sensitivity analysis of microstructure and mechanical properties to welding parameters for linear friction welded rail steel joints

Mechanical and Tribological Behaviors of U75VG Rail Flash−Butt Welded Joint

Effect on Hardness and Microstructures of Rail Joint with Narrow Gap Arc Welding by Normalizing

Effect Of Heat Treatment On The Microstructure And Properties Of A Ti3al Linear Friction Welding Joint

Improving the microstructures and mechanical properties of U71Mn rail steel liner friction welded joint by normalizing treatment

Quasi-equal Strength and Toughness Matching Rail Steel Joint Obtained Via Friction Welding below Ac1 Temperature

Effect of Normalizing Temperature on Hardness and Microstructure of Rail Joints with Narrow-Gap Automatic Arc Welding

Abnormal Grain Growth in the Heat Affected Zone of Friction Stir Welded Joint of 32Mn-7Cr-1mo-0.3n Steel During Post-Weld Heat Treatment

Effect of Heat Treatment on the Microstructure and Properties of a Ti<sub>3</sub>Al Linear Friction Welding Joint

Factors Influencing the Perceived Level-Straight Quality of the Welded Rail Joints

Analysis of the Impact Toughness Test and Fracture of Rail Thermit Welding Joints at Low Temperature

Effects of Post-weld Heat Treatment on Microstructure, Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints