Abstract:Statement of problem: Dental implants are particularly susceptible to occlusal overloading because, unlike natural teeth, they lack a periodontal ligament to help absorb occlusal forces. However, studies evaluating the impact of different crown and luting materials on the damping behavior and strain distribution of implant-supported crowns are lacking. Purpose: The purpose of this in vitro study was to investigate the damping behavior and strain distribution of peri-implant bone associated with 5 different CAD-CAM implant-supported crowns and 3 luting materials. Material and methods: A titanium implant was embedded in a plastic tube with epoxy resin and 5 different crown materials (polymethyl methacrylate, resin-infiltrated ceramic, lithium disilicate, titanium, and zirconia) luted to prosthetic abutments with 3 different luting materials (zinc oxide non-eugenol cement, zinc phosphate cement, and adhesive resin cement) and an uncemented condition were tested (n=5). Strain gauges were attached at the crestal and apical levels of the implant model. All specimens were load tested from 0 to 200 N. Slopes of load/time, microstrain/time, and time required to reach the maximum load were examined to represent the damping behavior. Absolute maximum strain (AMS) and its occurrence level were examined to represent the strain distribution. Two-way ANOVA, followed by the Tukey HSD test, were used for statistical analysis (α=.05). Results: All slopes and times to reach the maximum load in each crown material were statistically similar (P>.05), except for the polymethyl methacrylate group, which showed less steepness in all slopes and more time required to reach the maximum load significantly (P<.05). Both the polymethyl methacrylate group (224.5 ±30.2) and the titanium group (224.0 ±24.3) exhibited significantly higher AMS at the crestal level compared with the resin-infiltrated ceramic group (210.6 ±5.0) (P<.05). The lithium disilicate (218.1 ±15.0) and zirconia groups (217.3 ±14.8) demonstrated comparable AMS values with the others (P>.05). The uncemented group demonstrated steeper slopes and less time required to reach the maximum load compared with the adhesive resin group (P<.05), while slopes and times of the zinc phosphate and zinc oxide non-eugenol groups were comparable (P>.05). The uncemented group (242.7 ±25.3) exhibited significantly higher AMS at the crestal level than the other groups (P<.05). Conclusions: The crown material significantly affected the damping behavior of peri-implant bone, unlike the luting material. Polymethyl methacrylate with a high damping behavior exhibited high strain at the crestal level. In contrast, resin-modified ceramic with a moderate damping behavior exhibited low strain at the crestal level. Strain at the crestal level could be effectively reduced by approximately 13% through cementation.

Effects of Different Full-Crown Materials on the Amounts of GCF and the Level of AST and ALP in GCF

Changes of nickel and chromium contents in gingival tissue and gingival crevicular fluid after porcelain-fused-to-nichrome crown restoration

Effects of Ni-Cr Based Porcelain-fused-metal (PFM) Crown on Gingival Health of the Restored Teeth

Comparison of the microecology and total protein of GCF between the teeth restored by Ni-Cr based porcelain-fused-metal crown and control teeth

The influence of metal ceramic crown restoration on periodontal health of restored tooth

The Influence of Different Materials and Locations of Crown Margin on Periodontal Tissue of Human

Comparison of marginal fit of gold electroforming-ceramic crown,high gold alloy-ceramic crown and nickel chromium alloy-ceramic crown

Influence of Temporary Crowns on the Periodontal Conditions

[Effects of Change of Crown Contour on Health of Gingiva].

[Effect of gingival biotype on total crown repair and gingival crevicular fluid inflammatory factors]

Effects of periodontal tissue in the gingival retraction before the cementation of zirconia ceramic crowns on an-terior teeth

Effect of three different expansion methods on the level of AST and ALP in gingival crevicular fluid

[Influence of All-Ceramic and Porcelain-Fused-to-metal Restorations on Peri-Implant Gingival Discoloration:A Spectrophotometric Comparison].

In vitro damping and strain distribution for implant-supported crowns using 5 different CAD-CAM crowns and 3 different luting cements

Expression Level and Clinical Significance of Inflammatory Cytokines and Biochemical Markers in Gingival Crevicular Fluid During Different Crown Adhesion Patterns of Dental Implant

Comparison of fatigue lifetime of new generation CAD/CAM crown materials on zirconia and titanium abutments in implant-supported crowns: a 3D finite element analysis

Comparative study of two different fixed appliances on the changes in GST-ALP level during distal movement of canines

Evaluation of periodontal parameters on abutment teeth rehabilitated with single-unit crowns: A 12-month follow-up

Investigation on the Urine Excretion of Nickel and Chromium Related to Nickel-Chromium Alloy Dental Restoration

[Short-Term and Long-Term Effects of All-Ceramic Onlay on Restoration of Premolars and Its Influence on Dental Function].

Biocompatibility and acid resistance of preformed crowns in children: an in vitro study