Ion Chromatographic Determination of Fluorine and Chlorine by Water Vapor Distillation

Ke Wang

2001-01-01

Abstract:After separation by water vapor distillation fluorine and chlorine in silver ore were determined by ion chromatography. This method is rapid, simple and has wide linear range, good precision. It has been appliecl to the analysis of samples with satisfactory results.

What problem does this paper attempt to address?

Determination Of Fluoride In Soil Water Extract By Ion Chromatography With Column-Switching Technique

Xinhua Jiang,Chengzhu Ni,Binhe Zhu,Xunyan Zhao,Suqing Chen,Weide Lv,Jiajie Zhang,Peimin Zhang,Gang Li,Yan Zhu

DOI: https://doi.org/10.3724/SP.J.1123.2015.12025

2016-01-01

Chinese Journal of Chromatography

Abstract:A new method was proposed for the determination of fluoride in soil water extract by ion chromatography with column-switching technique. A reversed-phase column was used as a pretreatment column on-line to separate fluoride and organic acids as well as to eliminate organics. Fluoride was collected by a collection loop and delivered to the analytical system. Under the optimum conditions, the linear range of the method for fluoride was 0.05-10. 0 mg/L (r=0. 999 9), and the limit of detection (S/N =3) was 5. 50 g/L. The recovery was in the range of 103. 4%-105. 3% with the relative standard deviation of 2. 0%-2. 1%. The method could be applied to determine fluoride in complicated samples.
Determination of Trace Chloridion and Sulfate Ion in Sodium Fluoride by Ion Chromatography

Chunhui Yan,Mei Wang,Muzi Chen,Zhen Jin,Yong Zhang,Hongmei Sun

DOI: https://doi.org/10.3969/j.issn.1008-6145.2016.06.025

2016-01-01

Abstract:A method for the simultaneous determination of trace Cl–and SO42– in sodium fluoride by ion chromatography with suppression conductivity detector was established. The separation was achieved on IonPac AS11–HC column with KOH solution as the mobile phase. The concentration of Cl–was linear with chromatographic peak area in the range of 0.1–0.4 mg/L, r=0.999 9; The concentration of SO42–was linear with chromatographic peak area in the range of 0.2–1.0 mg/L, r=0.999 6. The mean recovery were 98.0%and 95.4%, the relative standard deviations were 2.14%and 1.22%, and detection limits were 0.011 mg/L and 0.014 mg/L for Cl–and SO42–, respectively. This method has good linearity and selectivity,it can be used as the quality control method for Cl–and SO42–in sodium fluoride.
Direct Quantitative Analysis of Fluorine in Solid Samples by Cryogenic Laser Ablation and Ionization Time-of-Flight Mass Spectrometry.

Zhenjian Zhang,Siyuan Ma,Le Hang,Zhouyi Xu,Wei Hang

DOI: https://doi.org/10.1021/acs.analchem.2c04372

IF: 7.4

2023-01-01

Analytical Chemistry

Abstract:The determination of fluorine, the lightest element in halogens, suffers from high ionization potential and spectral interference from water molecules in mass spectrometry. Herein, we introduced a liquid nitrogen cooling unit into the laser ablation and ionization source for the first time to construct a cryogenic laser ablation and ionization time-of-flight mass spectrometry (Cryo-LAI-TOFMS) system. With this system, the interference of water-related species at m/z 19 was effectively eliminated, and fluorine atomization and ionization efficiency could reach 6.3%. A direct quantitative analysis method was developed to determine fluorine contents in phosphate rock, copper ore, industrial byproduct gypsum, stream sediment, and soil. Considering the simplicity, high sensitivity, and low spectral interference of this technique, it can be extended to the determination of fluorine content as low as μg/g in complex solid samples.
Determination of Fluorine and Chlorine in Coal by High Temperature Combustion Hydrolyzing-Ion Chromatography

Fang Wang,Haifeng Wang,Jian Xu,Qian Wang,Naijie Shi

DOI: https://doi.org/10.3969/j.issn.1008-6145.2016.04.007

2016-01-01

Abstract:The method of high temperature combustion hydrolyzing-ion chromatography for the simultaneous determination of chlorine andfluorine in coal was established. Focused on the elimination of system drift, the method of interval measuring coal certified reference materials and coal samples was used to reduce the system drift from the changes of coal certified reference material properties,and improve the accuracy and repeatability. The content offluorine was linear with peak area in the range of 0.042–2.018μg/mL, the linear correlation cofficientr=0.995 8,the detection limit was 0.011μg/g,and the relative standard deviation of detection results was 6.32%(n=6). The content of chlorine was linear with chromatographic peak area in the range of 0.046–2.292 mg/mL, the linear correlation coefficientr=0.999 8,the detection limit was 0.010μg/g, and the relative standard deviation of detection result was 0.7%(n=6). Coal certified reference material was detected with the method, and the detection results were consistent with standard value. This method is fast, sensitive, and accurate, it is suitable for the determination offluorine and chlorine in coal samples.
Simultaneous Determination of Trace Fluorine and Chlorine in Iron Ore by Combustion-Ion Chromatography (C-IC)

Tong Li,Hong Min,Chen Li,Chenglin Yan,Linping Zhang,Shu Liu

DOI: https://doi.org/10.1080/00032719.2021.1875228

2021-01-28

Analytical Letters

Abstract:The determination of trace fluorine and chlorine in iron ore commonly requires complicated and time-consuming pretreatment involving alkali fusion, combustion in bombs, and pyrohydrolysis that prevent analysis of large numbers of samples. In this study, a rapid combustion-ion chromatography (C-IC) method for the simultaneous determination of fluorine and chlorine in iron ore is reported for the first time. The solid sample injection method, combustion time, sample mass, and absorption solution were optimized. The limits of detection for fluorine and chlorine were 0.029 mg g−1 and 0.031 mg g−1, respectively, which were similar to those for GB/T 6730.69-2010. Eight certified reference materials and three iron ore samples were used to evaluate the accuracy and precision of C-IC. The fluorine and chlorine content in the iron ore samples were from 0.086 to 1.773 mg g−1 and 0.050 to 3.10 mg g−1. The relative standard deviations for fluorine and chlorine were from 0.77% to 4.27% and 1.36% to 3.74%. The recoveries ranged from 95.3% to 104.6% and 91.9% to 104.3%. The results of iron ore samples determined by GB/T 6730.69-2010 and C-IC were in good agreement. C-IC is environmentally friendly and its suitability for automation may improve the analytical throughput.

chemistry, analytical
High-sensitive Detection of Fluorene by Ambient Ionization Mass Spectrometry

Jing He,Wenxin Wang,Hong Zhang,Kai Yu,Guangfeng Kan,Yingying Wang,Changlu Guo,Junyu Liu,Jie Jiang

DOI: https://doi.org/10.1039/d1nj01569a

IF: 3.3

2021-01-01

New Journal of Chemistry

Abstract:High sensitive analysis for fluorene at the sub-ng L−1 level in real water samples was achieved by nebulization-dielectric barrier discharge ionization.
Application of Ion Chromatography for Determination of Iodine in a variety of Water

Bingbing Song,Yun Tian,Yueping Luo,Hailan Lin,Junping Bi,Rilong Zhu,Sha Xie,Yan Chen

DOI: https://doi.org/10.3969/j.issn.1673-1212.2015.10.029

2015-01-01

Abstract:A method for determination of iodide in a variety of water by ion chromatography is presented.It was based on an IonPac AS19 Column with KOH as eluent and a conductive detector.This paper discussed the interference and elimination, the optimization of chromatographic conditions, the analysis methods of the linear and the detection limit, precision, accuracy, etc.This method was applied to determine iodide in a variety of water.The results show that this method is not subject to other anion interference, and it has low detection limits, wide linear range and good correlativity(R2 =0.999 9).The precision and accuracy were excellent.This method is simple and accurate.It was applicable to determine iodide in a variety of water.
Ion Chromatography for Rapid and Sensitive Determination of Total Chlorine in Water

Miao Huang,Yiping Hang

DOI: https://doi.org/10.1080/00032719.2012.675486

2012-01-01

Analytical Letters

Abstract:In this article, we report a new method that involves adsorption, oxygen bomb combustion, and ion chromatography for the preconcentration and determination of adsorbable organic halogen. This method can be divided into four steps, including: macroporous resin adsorption enrichment, optimization, oxygen bomb combustion, and ion chromatography determination. The project studies the macroporous resin adsorb organic halide pollutants and subsequent burn by an oxygen bomb combustion analyzer. The organic halogen in the aerobic environment combusts into hydrogen chloride. The water absorbing hydrogen chloride was then determined by ion chromatography. The influences of some adsorption and combustion parameters, such as the adsorption time, adsorption solution volume, solution pH, hexachlorobenzene acid concentration, combustion oxygen pressure, among others, on their respective adsorption efficiency were investigated. In the optimal condition, the adsorption time was 3.5 h; solution volume was 20 mL; pH was 4; combustion absorption time was 15 min; and the chloride calibration working range was from 1 ppm to 20 ppm (R-2 = 0.9998). Finally, the proposed method was successfully applied to the determination of organic halogen in water samples. The recoveries of chlorine (at spiked concentrations of 10 ppm and 20 ppm into water) in real samples ranged from 92.2% to 101.0%. Intra-day precision (N = 3) in terms of peak area, expressed as relative standard deviation, was found to be within the range of 0.68%-1.97%.
Simultaneous Determination of Hydrochloric Acid, Sulfuric Acid and Fluoride in Workplace Air by Ion Chromatography

ZHONG Xiu-xia,HUANG Jie-ling,ZHENG Li-wen,YU Ze-wen,CHEN Wei-dong,FENG Wen-xi

DOI: https://doi.org/10.13329/j.cnki.zyyjk.2012.06.002

2010-01-01

Abstract:[Objective]To explore the simultaneous determination of hydrochloric acid,sulfuric acid and fluoride in workplace air by ion chromatography.[Methods]Hydrochloric acid,sulfuric acid and fluoride were adsorbed by porous glass tube and detected by ion chromatography with best instrument condition and suitable mobile phase.[Results]Determination limit of hydrochloric acid,sulfuric acid and fluoride was 0.06 mg/L,0.35 mg/L and 0.08 mg/L; the RSDs for 3 materials were all less than 4.63%; the recovery range was 95.0%~102.2%.[Conclusion]This method is simple,with high sensitivity and good precision.
Simultaneous Determination of Fluoride and Chloride in Iron Ore by Steam Distillation Followed by Ion Chromatography

Nadeem Muhammad,Lehua Lao,Azeem Intisar,Hairong Cui,Yan Zhu

DOI: https://doi.org/10.1007/s10337-019-03798-7

2019-01-01

Chromatographia

Abstract:This study illustrates the extraction of fluoride (F−) and chloride (Cl−) from non-combustible inorganic iron ore matrix by employing steam distillation (SD)-based volatilization process followed by ion chromatographic (IC) determination. This cost-effective, simple and green sample preparation setup involved decomposition of sample matrix in H2SO4 for the extraction of volatile halides at 165–180 °C that were subsequently collected in a 100-mL receiving bottle having 0.2 M NaOH as absorption solution. After 15–20 min of absorption, the distillate was injected to the IC system for the isocratic separation and determination of both halides in complex inorganic iron ore sample (IOS). The developed method showed good linearity in the concentration range of 0.02–10 µg/mL with a correlation coefficient (R) greater than ≥ 0.9999. It also showed good accuracy (82.20–87.87%), precision (RSDs ≤ 3.71) and excellent limit of detection (LOD) ranged between 0.0003 and 0.0006 µg/mL with no matrix effect.
Ion Chromatography for Simultaneous Determination of Bromate,chlorite and Chlorate in Drinking Water

Huayong Wang

2012-01-01

Abstract:Objective:To develop an ion chromatography(IC) for simultaneous determination of chlorite,chlorate and bromate in drinking water.Methods:The IC separation was carried out with the IonPAC AS19 column by using hydroxide eluent at the flow rate of 1.0 ml/min.The injection volume was 500 μl.Conductivity detection cell temperature was set at 30℃,column temperature was set at 35℃.Suppressor was in automatic regeneration mode,suppressor current was 87 mA.Results:The results showed that in the range of 0 μg/L to 500 μg/L,the linear equation of chlorite was y=2.640x-0.027,r=0.9999,the detection limit was 0.1 μg/L;In the range of 0 μg/L~100 μg/L,the linear equation of bromate was y=1.342x-0.003,r=0.9999,detection limit was 0.5 μg/L;In the range of 0 μg/L~500 μg/L,the linear equation of chlorate was y=2.157x-0.043,r=0.9999,the detection limit was 0.2 μg/L.The recovery rates were 99.70%~102.6% and the relative standard deviations(RSD) were 1.16%~3.56%.Conclusion:The method is simple,fast,accurate,sensitive,little interference and applicable to the simultaneous determination of chlorite,chlorate and bromate in drinking water.
2', 4', 5', 7'-Tetrabromo-4,5,6,7-tetrachlorofluorescein-ag+-cl￣adsorptive Precipitation Reaction Coupled with Light-Absorption Ratio Variation Approach for Determination of Cl￣

王红艳,潘禄亭,白晶,郜洪文

2008-01-01

Abstract:Based on adsorptive precipitation reaction between silver chloride particles and 2′,4′,5′,7′-Tetrabromo-4,5,6,7-Tetrachlorofluorescein,a method called light-absorption ratio variation approach was proposed to determine chloride ions in water samples.The linear range is 0～1 mg/L and detection of limit is 0.03 μg/mL.Three ground waters were analyzed and the determined value is in a good agreement with that obtained by ion chromatography.The system could be used in solutions with strong ionic strength and high temperature.This method is cheap and has high sensitivity and selectivity.It can applied in site or in line to determine Cl-in sea water or samples with high temperature.
SIMULTANEOUS DETERMINATION OF FLUORINE AND CHLORINE IN COAL BY HIGH TEMPERATURE COMBUSTION HYDROLYSIS-ION CHROMATOGRAPHY WITH ON-LINE ELUENT GENERATOR

Li Yingri,Deng Shuang,Wang Hongmei,Zhang Fan,Wang Linlin,Chen Xiaopeng

DOI: https://doi.org/10.13205/j.hjgc.2011.05.007

2011-01-01

Environmental engineering

Abstract:Using high temperature combustion hydrolyzing coal sample and ultra-pure water absorption equipment,the method of high temperature combustion hydrolysis-ion chromatography with on-line eluent generator is established,which can determine fluorine and chlorine in coal at the same time.The main affecting factors are investigated,and the optimum detecting conditions of high temperature combustion hydrolysis preprocessing coal sample and ion chromatography are determined.The method can also be extended to measure fluorine and chlorine in fly ash,soil and rock,since the errors between the testing values and the real values of standard material are very little and meet the determination requirements.
Application of Ion Chromatography to Determine Bromate in Water

Yonghua Wang

2008-01-01

Abstract:Trace bromate in drinking water was determined by ion chromatography with suppressed conductivity detector.To reduce effect of high concentration interference component on analysis result,chloride was disposed.Those results show when the concentration of bromate is from 5 ng/ml to 100 ng/ml,linear relationship of this method is very well and its regression coefficient is 0.999 9.Furthermore,quantitative limit of this method was 2 ng/mL when S/N was equal to 10,and recovery of it was lager than 91.6 %.After testing,it is proved that this method could be used to determine bromate content in any drinking water.
Simultaneous determination of monofluoroacetate, difluoroacetate and trifluoroacetate in environmental samples by ion chromatography.

Fang Wang,Greg W Dicinoski,Yan Zhu,Paul R Haddad

DOI: https://doi.org/10.1016/j.chroma.2003.10.133

IF: 4.601

2004-01-01

Journal of Chromatography A

Abstract:A method is reported for the sensitive, simultaneous determination of mono- (MFA), di- (DFA), and trifluoroacetates (TFA) by ion chromatography (IC). These species were separated using a Dionex AS17 anion-exchange column employed with a potassium hydroxide gradient (via a Dionex EG40 eluent generator) and suppressed conductivity detection. The fluoroacetates were successfully separated from a range of inorganic and organic species likely to be present in environmental samples, in a total analysis time of 35min (including re-equilibration of the column). Detection limits for mono-, di- and trifluoroacetate were 21, 38 and 36μg/l, respectively, determined using a signal-to-noise ratio of 3, and were obtained using a sample injection volume of 50μl. Precision was less than 0.83% relative standard deviation (RSD) for replicate injections performed over a period of 30 days. The method was applied to the determination of monofluoroacetate in river water samples and also in carrot baits.
Matrix Interference Study: Determination of Halogens in Standard Steel Residues and Zinc Sulfide Concentrates by Ion Chromatography

Nadeem Muhammad,Amjad Ali,Irshad Hussain,Qamar Subhani,Dan-Dan Guo,Hai-Rong Cui,Yan Zhu

DOI: https://doi.org/10.1016/j.cjac.2022.100147

2022-01-01

SSRN Electronic Journal

Abstract:The sensitive determination of trace fluorine and chlorine contents in complex inorganic matrices such as steal residues and zinc sulfide concentrates is challenging cause difficulty in their digestion and presence of various matrix interferences species. Therefore, in this study, the effect of various constituent elements of geological samples including Ni, As, Ag, Pb, Hg, Co, SiO2, Bi, Sb, Cr, Zn, Cd, Ag, CaO, MgO, Al, Fe, KBr, and KI on the alkali-fused steam distillation-based recoveries of fluoride and chloride were investigated for better understand-ing the application of this method in various geological samples. Hence, a simple, cost-effective and modified alkali fusion-steam distillation-ion chromatography (SD-IC) method was developed for the sensitive and selective determination of halogens in standard steel resides and zinc sulfide concentrate samples. For optimum extraction of analytes various digestion parameters including alkali fusion amount, fusion temperature, and fusion time along with distillation volume were sequentially optimized. The developed method shows good linearity in the range 0.2 -3.0 mg/kg with correlation coefficient (r) values greater than 0. 99991. The limit of detection for flu-oride and chloride were appeared 0.07326 mg/kg and 0.02331 mg/kg, respectively with precision (repeatability and the intermediate precision) less than 4.12%. The results of standard steal residue and zinc sulfide concen-trate samples were in good agreement (91.27-100.18%) with their certified reference values (CRMs). SD-IC is a simple, cost-effective, and sensitive method for the determination of fluoride and chloride contents in complex geological samples (steal residues and zinc sulfide concentrates).
Determination of Residual Sulfur Dioxide in Fritillaria thunbergii Miq.by Ion-chromatography Method

ZHOU Jianliang,SHI Bei,LUO Lei,CHEN Bilian

DOI: https://doi.org/10.13748/j.cnki.issn1007-7693.2012.11.002

2012-01-01

Abstract:OBJECTIVE To establish an ion-chromatography method for determination of residual sulfur dioxide in Fritillaria thunbergii Miq.METHODS The samples were analyzed by Dionex ICS-3000 ion-chromatography after distilled by steam,absorbed by 3% hydrogen peroxide.RESULTS The linear range of sulfate radical was 0.000 05?2 ?g(r=1.000).The average recovery was 97.8% with the RSD of 2.1%(n=9).CONCLUSION The method is rapid,simple,sensitive,which shows good precision and reproducibility.It is suitable for determination of residual sulfur dioxide in Fritillaria thunbergii Miq.
Determination of Resorcinol and Phloroglucinol in Environmental Water Samples Using Ion Chromatography with Chemiluminescence Detection

Wu Hong-Wei,Chen Mei-Lan,Shou Dan,Zhu Yan

DOI: https://doi.org/10.1016/s1872-2040(11)60588-4

2013-01-01

Abstract:A novel method was established for the simultaneous determination of resorcinol and phloroglucinol in environmental water samples by ion chromatography with chemiluminescence detection. Using 50 mM NaOH as eluent, resorcinol and phloroglucinol can be separated well with IonPac AS19 column and determined on the basis of chemiluminescence reaction of luminol and K4Fe(CN)6 in a alkaline medium. The optimal CL conditions were 6.0 × 10−4 M luminol, 0.1 M K4Fe(CN)6 and 5.5 × 10−5 M K3Fe(CN)6. The absence of methanol and acetonitrile in mobile phase made the proposed method more sensitive. Under the optimal conditions, the detection limit (LOD) of resorcinol and phloroglucinol were 4.0 and 4.3 μg L−1, respectively. The method showed good linearity within the range of 0.05-1.0 mg L−1. The relative standard deviations (RSD) for 0.1 mg L−1 resorcinol and phloroglucinol standard solutions were 0.9% and 1.1% (n = 11). The method was successfully applied to the determination of resorcinol and phloroglucinol in environmental water samples.
Determination of Trace Amounts of Chromium (vi) by Flow Injection Analysis with Chemiluminescence Detection

Shamsa Kanwal,Qiang Ma,Wenchao Dou,Guannan Wang,Xingguang Su

DOI: https://doi.org/10.1080/03067310903353503

2012-01-01

International Journal of Environmental Analytical Chemistry

Abstract:A new sensitive chemiluminescence (CL) method combined with continuous flow injection analysis is described for the determination of Cr(VI). Strong CL signals were generated by Cr(VI)-catalysed oxidation of gallic acid in the presence of potassium permanganate and hydrogen peroxide. Effects of reagent concentrations, temperature, pH, flow rates, mixing coil length and mixing flow sequences on the chemiluminescence intensity were studied. Under the optimised experimental conditions, the relationship between the logarithm of concentration (log C) of Cr(VI) and the logarithm of intensity (log I) is linear over the range of 2 x 10(-11)-5 x 10(-4) mol L-1, with the detection limit (3 sigma) of 4 x 10(-12) mol L-1. Relative standard deviation of ten measurements of 1 x 10(-9) mol L-1 Cr(VI) is 1.7%. This flow injection analysis (FIA) system proved to be able to analyse up to 40 samples h(-1). Effects of various interferences possibly present in the water samples were investigated. Most cations and anions, as well as organic compounds, did not interfere with the determination of Cr(VI) in water samples. The experimental results obtained for chromium in reference materials were also in good agreement with the certified values.
Determination of Traces of Anions in Trifluoromethanesulfonic Acid Agent by Ion Chromatography

ZHENG Bo,DU Xiao-ning,ZHANG Wei-bing,SONG Ming-ming,CAI Yin-ping

DOI: https://doi.org/10.19319/j.cnki.issn.1008-021x.2013.04.019

2013-01-01

Abstract:A method was developed for detecting traces of inorganic anions in the trifluoromethanesulfonic acid agent by ion chromatography with suppressed conductivity detection.In this research,the influence of the pretreatment,the concentration of sample and column temperature to the experimental results and separation effect has been discussed.Based on the optimal ion chromatography,this study overcame the detection interference of SO2-4 anion from high CF3SO-3anion background,and detected the traces of F-,Cl-and SO2-4 anions by external reference method.The simplicity,accuracy and robustness of this method would make it a good applied perspective.

Ion Chromatographic Determination of Fluorine and Chlorine by Water Vapor Distillation

Determination Of Fluoride In Soil Water Extract By Ion Chromatography With Column-Switching Technique

Determination of Trace Chloridion and Sulfate Ion in Sodium Fluoride by Ion Chromatography

Direct Quantitative Analysis of Fluorine in Solid Samples by Cryogenic Laser Ablation and Ionization Time-of-Flight Mass Spectrometry.

Determination of Fluorine and Chlorine in Coal by High Temperature Combustion Hydrolyzing-Ion Chromatography

Simultaneous Determination of Trace Fluorine and Chlorine in Iron Ore by Combustion-Ion Chromatography (C-IC)

High-sensitive Detection of Fluorene by Ambient Ionization Mass Spectrometry

Application of Ion Chromatography for Determination of Iodine in a variety of Water

Ion Chromatography for Rapid and Sensitive Determination of Total Chlorine in Water

Simultaneous Determination of Hydrochloric Acid, Sulfuric Acid and Fluoride in Workplace Air by Ion Chromatography

Simultaneous Determination of Fluoride and Chloride in Iron Ore by Steam Distillation Followed by Ion Chromatography

Ion Chromatography for Simultaneous Determination of Bromate,chlorite and Chlorate in Drinking Water

2', 4', 5', 7'-Tetrabromo-4,5,6,7-tetrachlorofluorescein-ag+-cl￣adsorptive Precipitation Reaction Coupled with Light-Absorption Ratio Variation Approach for Determination of Cl￣

SIMULTANEOUS DETERMINATION OF FLUORINE AND CHLORINE IN COAL BY HIGH TEMPERATURE COMBUSTION HYDROLYSIS-ION CHROMATOGRAPHY WITH ON-LINE ELUENT GENERATOR

Application of Ion Chromatography to Determine Bromate in Water

Simultaneous determination of monofluoroacetate, difluoroacetate and trifluoroacetate in environmental samples by ion chromatography.

Matrix Interference Study: Determination of Halogens in Standard Steel Residues and Zinc Sulfide Concentrates by Ion Chromatography

Determination of Residual Sulfur Dioxide in Fritillaria thunbergii Miq.by Ion-chromatography Method

Determination of Resorcinol and Phloroglucinol in Environmental Water Samples Using Ion Chromatography with Chemiluminescence Detection

Determination of Trace Amounts of Chromium (vi) by Flow Injection Analysis with Chemiluminescence Detection

Determination of Traces of Anions in Trifluoromethanesulfonic Acid Agent by Ion Chromatography