Abstract:As regards significance of phase transformations and nature of phases developed as well as their affective role in the physical and mechanical properties and also corrosion resistance of ferritic stainless steel (FSS) welds, this paper wishes to investigate phases identification by means of electron backscattered diffraction (EBSD) analysis and mechanical performance via tensile test. For this goal, the sheets of FSS were prepared for the lap joints and successively, were welded by laser beam welding process under different pulse durations. No welding defects such as porosity, crack, etc., were seen, exhibiting prosperous joining process. Optical microscopy and EBSD corroborated the attendance of low-temperature (LT) and high-temperature (HT) heat-affected zone (HAZ). Fine-grained ferrite, intergranular martensite, as well as carbide precipitates were characterized in the LTHAZ, because of rapid cooling from the zone. Whereas, the HTHAZ was composed of coarse-grained ferrite and intergranular martensite by way of quenching from the zone. Phases characterization could show that the fusion zone (FZ) also had extremely coarsened ferrite and martensite at the grain boundaries. Grain coarsening might be responsible for weak crystallographic texture in this zone. The minimum and maximum microhardness allocated to the FZ and LTHAZ which were 174 5 HV and 261 11 HV, respectively. Founded on the tensile testing, it was apprehended that an increase in the pulse duration from 12 to 15 ms promoted the failure load and energy absorption by almost 13 and 327%, respectively. This was caused by joints strengthening through enhancing the weld penetration. However, an increase in the pulse duration from 15 to 18 ms resulted in degrading the failure load and energy absorption by around 31 and 95%, respectively. This arose from joints weakening due to intensifying grain coarsening phenomenon in the weld zone.

Microstructure Analysis on Materials of Electroslag Strip Welding(esw) with Austenitic Stainless Steel

Influence of arc energy on the microstructure and corrosion behavior of ER2209 duplex stainless steel deposited on Q345B low-alloy steel by GMAW

Effect of Arc Energy on the Microstructure and Electrochemical Behavior of Duplex Stainless Steel Weld Overlay Deposited by GMAW Process

Effect of Austenitic and Austeno-Ferritic Electrodes on 2205 Duplex and 316L Austenitic Stainless Steel Dissimilar Welds

Cold Metal Transfer Welding of Ferritic and Austenitic Stainless Steel: Microstructural, Mechanical, and Electrochemical Studies

Effect of microstructure heterogeneity on the mechanical properties of friction stir welded reduced activation ferritic/martensitic steel

Elucidating microstructural evolution and its effect on the mechanical properties of FSWed alumina-forming austenitic steel for power plant applications

Microstructure Evolution and Mechanical Properties of a Wire-Arc Additive Manufactured Austenitic Stainless Steel: Effect of Processing Parameter

Microstructure and mechanical properties analysis of S30408 joints by PAW+GTAW hybrid welding

Microstructure and mechanical properties of austenitic stainless steel welded with Co-based wires in cryogenic temperature environment

Investigation of microstructure and mechanical properties in dissimilar-metal welding between ferritic stainless steel and Co-based superalloy using electron beam welding

Microstructure evolution and mechanical properties in a gas tungsten arc welded Fe42Mn28Co10Cr15Si5 metastable high entropy alloy

Microstructure Evolution and Corrosion Behavior of Dissimilar 304/430 Stainless Steel Welded Joints

On the Microstructural Transformations and Mechanical Performance of Laser Beam Welded UNS S43000 Ferritic Stainless Steel

Insight on microstructure and mechanical properties of 40 mm thick-walled ferromagnetic super-MSS by magnetic-field-assisted narrow gap GTAW

Effect of Microstructure Evolution on Corrosion Behavior of Friction Stir Welded Joint for 2195-T8 Alloy

Effect of Microstructure on High-Strength Low-Alloy Steel Welded Joint Toughness with Simulation of Heat-Affected Zone Coarse-Grained Area

Investigation on microstructure evolution, mechanical properties and corrosion resistance of dual phase stainless steel joints welded by GTAW and SAW methods

Microstructure and mechanical properties of stainless steel clad plate welding joints by different welding processes

Microstructure, Mechanical Properties, and Corrosion Resistance of ER2209 Duplex Stainless Steel Manufactured by Plasma Arc Welding

Microstructure and corrosion characterization of weld metal in stainless steel and low carbon steel joint under different heat input