Design of the High-Speed Data Communication Interface in LED Display Screen

Fan Gan

2005-01-01

Abstract:A design on hardware and bottom software is provided,and the high speed slave FIFOUSB2.0exterˉnal interface of CY7C68013is adopted to implement data communication interface between PC and LED display screen.

What problem does this paper attempt to address?

Design of Data Communication Interface of Data Acquirement System Based on USB

陈章位,赵玉刚

DOI: https://doi.org/10.3321/j.issn:1004-132X.2004.20.014

2004-01-01

Abstract:An interface based on USB is designed for Data Acquirement System with DSP chips. Cypress EZ-USB technology and FPGA technology were used in this interface. This kind of interface can achieve high speed data communication between the Data Acquirement System and the PC in the USB 1.1 protocol, and it can meet the requirements of high speed and real-time requirements.
Design and Implementation of the High-Performance Link Layer in High-Speed Serial Communication

Yong-jian TANG,Le-nian HE,Xiao-lang YAN

DOI: https://doi.org/10.3969/j.issn.1000-7180.2005.04.037

2005-01-01

Abstract:The USB2.0 supports the high-speed signaling at 480 Mbps. It can meet the needs of image and voice signal transmitting. In this paper, after demonstration of the characters and functions of high speed digital circuit of USB2.0 link layer, a novel design and implementation method of data recovery circuits, which is based on all digital phase-looked loop (ADPLL), for the full-speed mode, as well as a new approach of parallel implementation of the encode/decode module in high-speed mode were proposed. The simulation results indicated that the circuit has reached 480MHz. A FPGA hardware simulation system was developed, in which the functions of link layer was verified.
Hardware interface design of high-speed communication module in ECT system

Zheng Weijun,Wang Baoliang,Huang Zhiyao,Li Haiqing

DOI: https://doi.org/10.3321/j.issn:0254-3087.2006.z1.246

2006-01-01

Abstract:Design of high-speed communication module based on USB2.0 is described.The interface between CY7C68013 which works in slave FIFO mode and DSP is given.And details of some key pins and several points of PCB design are explained.
Design and Realization of USB Interface Based on Series EZ-USB

XIE Wei-bang,WU Xiao-ming

DOI: https://doi.org/10.3969/j.issn.1003-8868.2011.03.001

2011-01-01

Abstract:Objective To design a high-speed USB interface which is used in community-oriented health care system.Methods To realize the high-speed data transmission between PC and monitoring system,the authors take good advantage of the EZ-USB-FX2 supplied by Cypress Company.After the brief description of CY7C68013a,it clarified the methods to design a high-speed USB interface by using CY7C68013a.The procedure includes hardware design,firmware development,driver production and PC program development.Results USB interface based on EZ-USB-FX2 was designed.A high-speed USB interface which was used in community-oriented health care system was supplied.Low cost and facilitation of the community-oriented health care system was realized.Conclusion The interface is convenient to be used in community-oriented health care system.
Realization of High-speed Data Transmission Based on USB Interface

吕超,张玉霞,王立欣

2009-01-01

Abstract:USB interface has the advantage of plug-and-play, easy to install, high-bandwidth, easy to expand and high-speed transmission. Despite the USB2.0 specification has reached the highest transmission speed of 60MB/s, but a lot of USB 2.0 devices actually worked in the data transmission quite different from it. The data acquisition system has been designed with FPGA as a central controller and CY7C68013 as a interface in this paper. When the interface chip CY7C68013 work at Synchronization slave FIFO mode, a block synchronization signal is designed to ensure the stability and highest transmission. The highest data transfers speed of the system is 31.8MB/s.
Design and Implementation of LED Display Screen Controller Based on STM32 and FPGA

xiao guang wu,cheng jun zhang

DOI: https://doi.org/10.4028/www.scientific.net/AMM.268-270.1578

2013-01-01

Applied Mechanics and Materials

Abstract:In order to realize point-light-source and hurdle lamp LED displays system, a kind of LED display screen controller design based on FPGA and STM32 is introduced by this paper. This design can quickly and easily receive display the data from USB, Ethernet and SD card interfaces through the STM32 processor, and use FPGA to realize data transmission throughput big operation of stable display by double RAM Ping-Pong operation This paper gives drive unit timing for TM1809 series LED drive chip as typical case. This design has applied to LED display controller with stability of reading data and excellent performance.
Design for USB interface of data acquisition system based on EZ-USB FX2

王东,李公平,潘小东,方登富

DOI: https://doi.org/10.3969/j.issn.1004-373X.2015.04.020

2015-01-01

Abstract:Taking EZ?USB FX2 interface chip as an example,several aspects involved with USB interface design of indus?trial CT data acquisition system are introduced in detail in this paper. In this design,Slave FIFO is used in EZ?USB chip to im?prove the speed of data transmission. In this way, the USB kernel is not involved in the data transmission. Inside the CY7C68013A chip,4 kB configurable endpoint buffer is contained. It is the large capacity data transmission terminal,which can be configured to fulfill high?speed data transmission with peripheral circuit,but does not need 8051 firmware program to join with. The basic framework is contained in the EZ?USB firmware program development kit provided by CYPRESS company. In this paper,the structure and characteristics of the CY7C68013A chip are introduced,the EZ?USB FX2 firmware frame is ana?lyzed,the firmware example code is given,the firmware code loading way is described,and the interface between application program and driver is illustrated. With USB interface developed by means of EZ?USB chip,the development difficulty was great?ly reduced,and the development efficiency was improved.
Design and Implementation of LED Large Screen Synchronous Display Control Systems

LIU Quan-li,WANG Chen-kai,WANG Wei,GAO Cong

2011-01-01

Abstract:A design scheme of full-color large LED screen synchronous display control system is proposed.The system receives video data by DVI interface and transmits data via Gigabit Ethernet.The hardware unit modules of system are implemented,including CPU XC3S250E,DVI interface,USB interface,Ethernet interface and LED large screen driving circuit.The system software of LED large screen is developed which has the function of program editing and broadcasting control.A graphical interface based on Visual Studio platform 2005 is introduced and the generic design and functions are included.The experiment test shows that the control system is reliable and the operation is convenient.
Design of USB Control System Based on CY7C68013A

赵铁军

DOI: https://doi.org/10.3969/j.issn.1004-373x.2010.13.060

2010-01-01

Abstract:With the increasing development of the communication technology,the universal serial bus(USB) as a new interface technology that makes the connection of PCs with peripheral equipments very simple has been extensively adopted.The feature of USB2.0 is introduced firstly,and then the overall plan for designing the control system by using CY7C68013A is presented.The function of the system firmware and the design of drive program are discussed in detail.The key issues which should be taken more attention during the system design are proposed.The control system firmware is programmed with C language.The control interface on PC is developed under the VC++6.0 development environment.The experiment indicates that the whole system runs perfectly well.
A Dual-Channel High-Speed Data-Acquisition System Based on USB2.0 Technique

YUE YUEPING,HUO YUJING,HE SHUFANG

DOI: https://doi.org/10.3969/j.issn.1008-0570.2007.19.042

2007-01-01

Abstract:A high- speed dual- channel Data- Acquisition System based on the CY7C68013 and MAX1195 is discussed in the paper. In the design, the FX2’s feature, the GPIF, which can totally remove the bottleneck caused by the 8051’s CPU, is used to achieve the maximum USB2.0 performance. No other microprocessor or CPLD or FPGA is needed. The paper has discussed both the hard- ware design and the software design of the system in great detail, including the firmware of the CY7C68013 and the user application program of the computer side. The system has been tested with a laser longitudinal mode analyzer experiment which proved the de- sign had achieved its original goals.
High Speed Transmission System Based on USB Interface Multi Bit Data Format

ZHANG Jinpeng,ZHAO Jianjun,TANG Haifeng,ZHAO En

DOI: https://doi.org/10.3969/j.issn.1672-9722.2017.12.026

2017-01-01

Abstract:This design realizes a data transmission system based on USB2.0 interface.The system from the FPGA to produce a 35-bit added to 250 from 0 of the counter,to achieve the value of the counter through the USB to the host computer's function.The design of the FPGA chip uses Altera's CycloneII EP2C5Q208C8N,USB chip Cypress's EZ-USB series CY7C68013A.Through the Quartus II software,Keil software,Cypress console for USB interface design of multi-bit data transmission system.The system can be used for high-precision,high-speed,low-cost bulk data transmission.
A design of LED full color display screen control system based on FPGA

Wu Xu-zhi

Abstract:This system designs a new architecture for LED full color scanning controller board by using C8051F340 MCU+FPGA module as the main control module to implement point-to-point control and full color screen display.It completes the acquisition of temperature and humidity within the display screen,power supply voltage monitoring,environmental luminosity monitoring outside the screen,the communication with upper computer and the FPGA configuration and control by using the flexibility and versatility of MCU.FPGA,as a high-speed device,is used to deal with data receiving and scanning,and constant current driver chip MBI5036IC is used to achieve LED constant drive.

Computer Science,Engineering
Design of Data Transmission System Based on FPGA and USB 2.0

Junsheng Wu,Fuzhou Shang,He Sun,Tian Qin,Qing Li

DOI: https://doi.org/10.4028/www.scientific.net/amm.321-324.417

2013-01-01

Applied Mechanics and Materials

Abstract:In this paper, a high-speed data transmission system based on FPGA (Field Programmable Gate Array) and USB 2.0 (Universal Serial Bus) technology is designed. Firstly, we introduce the hardware of the data transmission system, which includes data acquisition circuit, transmission circuit and power conversion circuit, etc. Secondly, the corresponding software design including USB firmware program, USB driver and firmware modification are described in detail. Finally, the corresponding experiment has been carried out, which show that the developed system will help to achieve the data transmission system with the characteristics of high-speed, integration and low power consumption, etc.
Design and Realization of MPC860's USB communication interface

Kang Hua,Zhang Xiaobin

2007-01-01

Abstract:Being an embedded communication processor which has formidable function,MPC860 not supporting USB will limits its application in some domain.So a method based on FT245BM to realize the MPC860's USB communicationg interface is been raised.There are two means to connect processor with FT245BM,one through the I/O ports of processor and the other though coding of CPLD.Because the I/O port of MPC860 are multiplexing,this method wastes the I/O port resource;Yet the CPLD coding will increase the cost and complexity of the product.S o The control logic sequences needed by FT245BM are realized through microinstruction programming in the MPC860 memory controller UPMA.The hardware and software design are describe in detail.And the method through VCP(Virtual COM Port)driver provided by FTDI to programme communication software on the PC is show as well.The testing prove the communication is stable and reliable,and the purpose to realize the USB interface on MPC860 is reached.
Design and Implementation of Data Uni-directional Transmission System Based on EZ-USB FX2

LI Bo,LIU Jia-yong,JIANG Yu,LIU Xian-kui

DOI: https://doi.org/10.3969/j.issn.1672-2892.2008.01.011

2008-01-01

Abstract:To satisfy the application requirements for host-computers uni-directional data trans- mission in different security ratings, a design scheme of uni-directional transmission system based on EZ-USB FX2 is presented in this paper. And the system which adopts the Universal Serial Bus(USB)2.0 chip Cy7c68013 and IDT72v06 First in First out(FIFO) memory, realizes uni-directional, high-speed, safe and reliable data transmission between the host-computers in different security domains, with hardware design of external FIFO through General Programmable Interface(GPIF) and application program.
Data Communication Between PC and FPGA in USB Mode

岳奎,刘少君,任参,黄道平

DOI: https://doi.org/10.3969/j.issn.1007-757x.2009.12.016

2009-01-01

Abstract:This paper introduces a method of data Communication between FPGA and PC based on USB protocol by the design of interface circuit with EZ_USB FX2 CY7C68013A and FPGA.And the paper introduces the design of firmware programmer,the character of Slave FIFO mode,the circuit design between Slave FIFO and FPGA and language VHDL design of write and read with FPGA interface.
Design of Large LED-screen Display Control System

ZHAO Cai-rong,DING Tie-fu,ZHENG Xi-feng,LIU Gao-xia

DOI: https://doi.org/10.3969/j.issn.1007-2780.2005.06.019

2005-01-01

Chinese Journal of Liquid Crystals and Displays

Abstract:According to the characteristics of the LED module structure, combining the technology of CPLD,the dynamic scanning display of the LED display screen was realized.A kind of large LED-screen display control system was designed. Under the control of core chip TMS320LF2407,the system finished the communication with the PC; at the same time, with the help of programmable logic device EP1K30, the control system finished the data store and update,cartoon processing, circulation showing etc. User interface and serial communication program were written with Visual C++. This system can work in off-line state and run for a long time in succession, and the cost is relatively lower.
High-speed Data Acquisition System Based on FT2232H

Wang Shu,Xiang Xinyi,Lin Peiqun,Xu Jianmin

2013-01-01

Abstract:Aiming at the requirements of transmission speed and development difficulty of various virtual instruments,an acquisition system on basis of new USB2.0high-speed interface is designed.In order to transmit data quickly among high-speed interfaces,this system employs the interface chip FT2232Hof FTDI Company's fifth generation USB2.0,using its asynchronous FIFO interface to transmit data to FSMC interface of STM32F103,and applies LabVIEW to design PC interface as well as making use of the available Dynamic Link Library(DLL)and Firmware Library MCU to achieve high-speed data transmission.
Design of universal data transmission system based on FPGA and USB3.0

Peng Kuang,Chong Liu,Yonggang Wang

DOI: https://doi.org/10.19358/j.issn.1674-7720.2017.07.008

2017-01-01

Abstract:Field-programmable gate array (FPGA) is used more and more in various fields due to the highly flexible and powerful ability of data processing.USB 3.0 is one of the mainstream data transmission protocols, with the advantages of fast speed and low power consumption.Implementing USB 3.0 interface on FPGA can effectively solve the problem of data transmission between FPGA and the host computer, greatly improve production efficiency.In this paper, a data transmission system between FPGA and the host computer is designed and implemented with the USB 3.0 controller CYUSB3014, which achieves transmission speed of up to 390 MB/s.
Research of Control Technology for LED Screen Based on CPLD(Ⅱ)Analysis of LED Software Program

XING Jian-ping,ZHANG Jun,ZHANG De-jing

DOI: https://doi.org/10.3969/j.issn.1005-9490.2006.03.082

2006-01-01

Abstract:The corresponding software design based on the hard wares,which includes the serial data receiver and the data saver and the information display,was made.Also by using the VHDL language,the program of UART,Memorizer Control and LED Screen Scan were developed.The problems encountered in testing and their solutions for the software design are discussed.The results include: the emulation procedure is very important for EDA;the microcomputer can control the information of the screen;the platform can work well without computer;the memorizer can keep saving the shown data when power down.

Design of the High-Speed Data Communication Interface in LED Display Screen

Design of Data Communication Interface of Data Acquirement System Based on USB

Design and Implementation of the High-Performance Link Layer in High-Speed Serial Communication

Hardware interface design of high-speed communication module in ECT system

Design and Realization of USB Interface Based on Series EZ-USB

Realization of High-speed Data Transmission Based on USB Interface

Design and Implementation of LED Display Screen Controller Based on STM32 and FPGA

Design for USB interface of data acquisition system based on EZ-USB FX2

Design and Implementation of LED Large Screen Synchronous Display Control Systems

Design of USB Control System Based on CY7C68013A

A Dual-Channel High-Speed Data-Acquisition System Based on USB2.0 Technique

High Speed Transmission System Based on USB Interface Multi Bit Data Format

A design of LED full color display screen control system based on FPGA

Design of Data Transmission System Based on FPGA and USB 2.0

Design and Realization of MPC860's USB communication interface

Design and Implementation of Data Uni-directional Transmission System Based on EZ-USB FX2

Data Communication Between PC and FPGA in USB Mode

Design of Large LED-screen Display Control System

High-speed Data Acquisition System Based on FT2232H

Design of universal data transmission system based on FPGA and USB3.0

Research of Control Technology for LED Screen Based on CPLD(Ⅱ)Analysis of LED Software Program