Abstract:Recently, energy conservation, environmental protection and security are the main factors considered by the automotive manufacturers. Medium-Mn steel with excellent combination of specific strength and ductility have been regarded as the potential candidates for automotive applications. The excellent combination of specific strength and ductility depends on the microstructure under different heat treatment processes of the steels. Therefore, the relationship of the combination of specific strength and ductility and microstructure should be studied in detail. Anew alloy system of aluminum-containing medium-Mn steel was developed in this study. The addition of aluminum stabilizes alpha-ferrite, and facilitates the presence of 6-ferrite during solidification. The addition of Mn and C compensates the effect of aluminum on phase stability and ensures austenite formation. In this investigation, the effects of intercritical annealing temperature on the microstructure and tensile properties of a newly designed cold-rolled aluminum-containing medium-Mn steel (0.2C-5Mn- 0.6Si- 3Al, mass fraction, %) were investigated by SEM, XRD and uniaxial tensile tests. The tensile results show that an excellent combination of ultimate tensile strength (sigma(b)) of 1062 MPa, total elongation (delta) of 58.2% and sigma(b) x delta of 61.8.% could be obtained after annealing at 730 degrees C. The inverted austenite of the cold-rolled steel coarsenes and gradually changes its morphology from mainly lamellar to mainly equiaxed with increasing intercritical annealing temperature, and a duplex microstructure consisting of multi-scale retained austenite could be obtained at 730 degrees C, which possesses suitable mechanical stability and thus presents prolonged transformation-induced plasticity (TRIP) effect during tensile deformation. This kind of sustainable TRIP effect and the cooperative deformation of ferrite are responsible for the superior mechanical properties. The investigation of tensile fracture behavior shows that the nucleation and growth of voids occurred mainly at the interfaces between soft ferrite and hard martensite induced by deformation.

Microstructure and Mechanical Properties of Additive Manufactured Steel-Al Structure Materials with Nickel Gradient Layers

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Phase constitution, microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing

Interface analyses and mechanical properties of stainless steel/nickel alloy induced by multi-metal laser additive manufacturing

Microstructure and Mechanical Properties of NiCrMoV Steel Fabricated by Double-Electrode Gas Metal Arc Additive Manufacturing

Microstructural Characteristics and Mechanical Properties of an Additively Manufactured Nickel-Based Superalloy

Additive manufacturing of an ultrastrong, deformable Al alloy with nanoscale intermetallics

The Characteristic Microstructures and Properties of Steel-Based Alloy via Additive Manufacturing

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Investigating the Influence of Al Contents on Microstructure and Mechanical Properties of Ni 3 Al Superalloy Fabricated by Twin Wire‐Based Direct Arc Energy Deposition

Microstructure and mechanical properties of twin wire and arc additive manufactured Ni3Al-based alloy

Microstructure and Mechanical Properties of Low-Carbon High-Strength Steel Fabricated by Wire and Arc Additive Manufacturing

Evolution of microstructure and mechanical properties in 2205 duplex stainless steels during additive manufacturing and heat treatment

Microstructures and mechanical properties of a modified 9Cr ferritic-martensitic steel in the as-built condition after additive manufacturing

Investigation on the Microstructure and Mechanical Properties of Multi-layer and Multi-pass Al Alloy Deposition Based on Cold Metal Transfer Technology

Multimaterial Additive Manufacturing of Graded Laves Phase Reinforced NiAlTa Structures by Means of Laser Metal Deposition

Microstructure Evolution and Mechanical Properties of a Wire-Arc Additive Manufactured Austenitic Stainless Steel: Effect of Processing Parameter

Microstructure transformation and mechanical behavior in NiTi alloys fabricated by dissimilar double wires arc additive manufacturing

Enhanced Interface Strength in Steel-Nickel Bimetallic Component Fabricated Using Wire Arc Additive Manufacturing with Interweaving Deposition Strategy