Abstract:High-energy rechargeable lithium metal batteries (LMBs) have attracted significant attention recently. These batteries can be bulit using high areal-capacity (>4 mAh.cm(-2)) layered oxide cathodes and thin lithium (Li) metal anodes (<50 mu m in thickness), whose cycle performance are severely limited by the unregulated growth of Li particles having high surface areas, including dendrites and mossy Li. To improve the cycle performance of LMBs, many approaches have been developed in recent years to promote dendrite-free and dense Li electrodeposition, such as electrolyte engineering (for liquid cells), Li anode surface modification, three-dimensional current collector design, and using solid-state electrolytes. In addition to these heavily researched chemical-based approaches, applying external pressure to LMBs can also strongly impact the morphology of the electrochemically deposited Li particles due to the malleable nature of metallic Li and has been shown to improve the cycle performance. However, the relationship between the applied pressure, morphological evolution of the Li anode and the cycle performance has not been fully understood, especially in coin cells, which are widely used for LMB research. Here we report a custom-designed pressure applying/measurement device based on thin-film pressure sensors to realize real-time tracking of the pressure evolution in LMB coin cells. Our results show that moderate pressure is conducive to dense Li deposition and increases the cycle life, whereas excessive pressure causes Li inward-growth and the deformation of Li anode, which will impare the electrochemical performance of LMBs. Although these observations are made in coin cells, they could have important implications for pouch cells and solid-state batteries, both of which are commonly tested under pressure. The cycle performance of LMBs is significantly improved in both coin cells (under actual relevant conditions) and large pouch cells. A 5 Ah pouch-type LMB with a high energy density exceeding 380 Wh.kg(-1) could achieve stable cycling over 50 cycles under a stack pressure of similar to 1.2 MPa. It was also confirmed that the cell holders or clamps commonly used for coin cells can only exert a small amount of pressure, which is unlikely to exaggerate the cycle performance of the LMB coin cells. However, we do suggest that the electrochemical performance of LMBs should be reported along with the information on the applied pressure. This research practice will improve the consistency and quality of the reported data in the LMB research community and help unite the efforts to further improve the high energy density LMBs.

Performance of Lithium-Ion Pouch Cells with Silicon Composite Anodes under External Mechanical Pressure

Effect of Mechanical Pressure on Lifetime, Expansion, and Porosity of Silicon-Dominant Anodes in Laboratory Lithium-Ion Cells

Effect of Mechanical Pressure on Rate Capability, Lifetime, and Expansion in Multilayer Pouch Cells with Silicon-Dominant Anodes

Mechanical behavior of Silicon-Graphite pouch cells under external compressive load: Implications and opportunities for battery pack design

Swelling, pressure evolution and aging in high-silicon/ graphite composite lithium-ion batteries

Effects of external pressure on cycling performance of silicon-based lithium-ion battery: modelling and experimental validation

Unlocking Failure Mechanisms and Improvement of Practical Li–S Pouch Cells through In Operando Pressure Study

Interfacial Behavior of a Thio-LISICON Solid-State Electrolyte under External Pressure

External Short-Circuit Scenarios under Different Mechanical Pressures Applied to Lithium-Ion Cells with Silicon-Dominant Anodes

Insights into the Swelling Force in Commercial LiFePO4 Prismatic Cell

The Beneficial Effect of Pressure for Lithium Ion Battery Cells through Gas Dissipation

A Pressure Self‐Adaptable Route for Uniform Lithium Plating and Stripping in Composite Anode

Tracking Pressure Changes and Morphology Evolution of Lithium Metal Anodes

Extending the Cycling Life of Lithium–Ion Batteries with Silicon/Graphite Composite Anodes by Automatic External Stress Regulation

Internal pressure regulation enables reliable electrochemical performance evaluation of lithium-ion full coin cell

In-situ obtained internal strain and pressure of the cylindrical Li-ion battery cell with silicon-graphite negative electrodes

Pressure-Induced Detour of Li$^+$ Transport during Large-Scale Electroplating of Lithium in High-Energy Lithium Metal Pouch Cells

Uncovering the impact of pressure on lithium-metal pouch cells with liquid electrolytes

Impact of Pressure Distribution and Magnitude on the Performance of Lithium Metal Anodes

Pouch cells with 15% silicon calendar-aged for 4 years

Effect of external pressure and internal stress on battery performance and lifespan