Abstract:Casting dimension significantly influences the quality and performance of finished products when employing a sequential solidification process. Tapered cylinder Mg-10Gd-0.2La-0.1Zn-0.4Zr (wt%) castings with variable section dimensions were fabricated by sand-cast process, and the role of section dimension on the solidification behavior, microstructures and mechanical properties under different thermal conditions were systematically investigated. Increasing section dimension from Phi 23 mm to Phi 32 mm, the average cooling rate during solidification decreases from 1.70 degrees C/s to 0.86 degrees C/s, and the actual chemical composition of Gd element descends from 10.39 +/- 0.11 wt% to 10.05 +/- 0.06 wt%. Meanwhile, the primary alpha - Mg grains are coarsened in size from 29 +/- 2 mu m to 39 +/- 3 mu m, and the area ratio of the secondary phase degrades from 1.87 +/- 0.19 % to 1.14 +/- 0.31 %. With a solution treatment of 500 degrees C x 8 h, the area ratio of the residual secondary phase rises from 0.55 +/- 0.06 % to 0.75 +/- 0.12 %, accompanied by the decrease of Gd solubility with a grand value of 0.33 wt%. The decline of Gd solubility is unfavorable for the precipitation of strengthening phases during the ageing treatment and leads to a reduction of similar to 13.5% in the area number density of the 13 ' precipitates. The strength and ductility at ambient temperature simultaneously worsen with increasing section dimension, in which the yield strength, ultimate tensile strength and elongation respectively descend from 230 +/- 7 MPa, 364 +/- 7 MPa and 8.5 +/- 1.1 % to 219 +/- 6 MPa, 336 +/- 5 MPa and 5.5 +/- 0.9 % in the peak-aged condition. The strength debasement is due to the grain coarsening and lower number density of the 13' precipitates, while the reduced ductility is attributed to the coarser grains and higher content of the residual secondary phase with larger size. Casting dimensions should be meticulously designed when developing high-performance Mg alloys by sequential solidification processes.

Linear Contraction of Sand Casting Mg–9Gd–3Y–0.5Zr Alloy

On the Dimension Contraction of Low-Pressure Sand Cast Mg-Gd-Y-Zr Alloy

Linear Contraction Behavior of Low-Carbon, Low-Alloy Steels During and After Solidification Using Real-Time Measurements

Section Dimension Induced Microstructure and Mechanical Properties Variations of Sequential Solidified Sand-Cast Mg-10gd-0.2la-0.1zn-0.4zr (wt%) Alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Prediction of Shrinkage Microporosity in Gravity‐Cast and Low‐Pressure Sand‐Cast Mg–6Gd–3Y–0.5Zr Magnesium Alloys

Effects of Gd/Y Ratio on the Microstructures and Mechanical Properties of Cast Mg-Gd-Y-Zr Alloys

Microstructure, mechanical properties and fracture behaviors of large-scale sand-cast Mg-3Y-2Gd-1Nd-0.4Zr alloy

Microstructure and mechanical properties of Mg-Gd-Y-Zn-Zr alloy prepared by rheo-diecasting

Influence of Heat Treatment on Cyclic Deformation and Low-Cycle Fatigue Behavior of Sand-Cast Mg–10Gd–3Y–0.5Zr Magnesium Alloy

A Comparative Study of Mg-Gd-Y-Zr Alloy Cast by Metal Mould and Sand Mould

Study on the Heat Transfer at the Casting-Mould Interface in Resin-Bonded Sand Mould Casting of Mg-Gd-Y-Zr Alloy

Microstructure and Mechanical Properties of Mg–3.0Y–2.5Nd–1.0Gd–x Zn–0.5Zr Alloys Produced by Metallic and Sand Mold Casting

Influence of pouring temperature on solidification behavior, microstructure and mechanical properties of sand-cast Mg-10Gd-3Y-0.4Zr alloy

Development of high strength sand cast Mg–Gd–Zn alloy by co-precipitation of the prismatic β′ and β1 phases

Influence of Extrusion Ratio on Microstructure and Tensile Properties of Mg–Gd–Y–Zn–Zr Alloy

The Tensile Properties and Fracture Toughness of a Cast Mg-9Gd-4Y-0.5Zr Alloy

Influence of different casting processes on high cycle fatigue behavior of Mg–10Gd–3Y–0.5Zr alloy

Achieving refined microstructures and improved mechanical properties in a cup-shaped Mg-Gd-Y-Zr alloy casting by novel near-liquidus squeeze cast process

Effect of chemical composition on the microstructure, tensile properties and fatigue behavior of sand-cast Mg–Gd–Y–Zr alloy

Effect of cooling rate on the microstructure and mechanical properties of sand-casting Mg-10Gd-3Y-0.5Zr magnesium alloy