Abstract:Casting dimension significantly influences the quality and performance of finished products when employing a sequential solidification process. Tapered cylinder Mg-10Gd-0.2La-0.1Zn-0.4Zr (wt%) castings with variable section dimensions were fabricated by sand-cast process, and the role of section dimension on the solidification behavior, microstructures and mechanical properties under different thermal conditions were systematically investigated. Increasing section dimension from Phi 23 mm to Phi 32 mm, the average cooling rate during solidification decreases from 1.70 degrees C/s to 0.86 degrees C/s, and the actual chemical composition of Gd element descends from 10.39 +/- 0.11 wt% to 10.05 +/- 0.06 wt%. Meanwhile, the primary alpha - Mg grains are coarsened in size from 29 +/- 2 mu m to 39 +/- 3 mu m, and the area ratio of the secondary phase degrades from 1.87 +/- 0.19 % to 1.14 +/- 0.31 %. With a solution treatment of 500 degrees C x 8 h, the area ratio of the residual secondary phase rises from 0.55 +/- 0.06 % to 0.75 +/- 0.12 %, accompanied by the decrease of Gd solubility with a grand value of 0.33 wt%. The decline of Gd solubility is unfavorable for the precipitation of strengthening phases during the ageing treatment and leads to a reduction of similar to 13.5% in the area number density of the 13 ' precipitates. The strength and ductility at ambient temperature simultaneously worsen with increasing section dimension, in which the yield strength, ultimate tensile strength and elongation respectively descend from 230 +/- 7 MPa, 364 +/- 7 MPa and 8.5 +/- 1.1 % to 219 +/- 6 MPa, 336 +/- 5 MPa and 5.5 +/- 0.9 % in the peak-aged condition. The strength debasement is due to the grain coarsening and lower number density of the 13' precipitates, while the reduced ductility is attributed to the coarser grains and higher content of the residual secondary phase with larger size. Casting dimensions should be meticulously designed when developing high-performance Mg alloys by sequential solidification processes.

Development of high strength sand cast Mg–Gd–Zn alloy by co-precipitation of the prismatic β′ and β1 phases

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructural Characteristics and Mechanical Properties of Cast Mg–3Nd–3Gd–xZn–0.5Zr Alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Microstructure and Mechanical Properties of Mg–3.0Y–2.5Nd–1.0Gd–x Zn–0.5Zr Alloys Produced by Metallic and Sand Mold Casting

Effect of Zn Addition on the Microstructure and Mechanical Properties of Cast Mg–10Gd–3.5Er– X Zn–0.5Zr Alloys

Characterization and Strengthening Effects of Γ′ Precipitates in a High-Strength Casting Mg-15Gd-1Zn-0.4Zr (wt.%) Alloy

Developing Mg-Gd-Dy-Ag-Zn-Zr Alloy with High Strength via Nano-Precipitation

Microstructure and Strengthening Mechanism of High Strength Mg–10Gd–2Y–0.5Zr Alloy

Section Dimension Induced Microstructure and Mechanical Properties Variations of Sequential Solidified Sand-Cast Mg-10gd-0.2la-0.1zn-0.4zr (wt%) Alloy

Influences of Gd on the Microstructure and Strength of Mg–4.5Zn Alloy

Microstructure and mechanical properties of cast Mg-6Gd–Zr alloy with different Y addition

Microstructure evolution and mechanical properties of an ultra-high strength casting Mg–15.6Gd–1.8Ag–0.4Zr alloy

Microstructures and Mechanical Properties of Mg-10Gd-3Y-2Zn-0.5Zr Alloy

A good balance between strength and ductility in Mg–Zn–Mn-Gd alloy

Microstructure and Super High Strength of Cast Mg-8.5gd-2.3y-1.8ag-0.4zr Alloy

Effect of Zn Addition on Microstructure and Mechanical Properties of Mg–9Gd–3Y–0.5Zr Alloy

Improving Strength and Ductility of Mg–Gd–Y–Zn–Zr Alloy Simultaneously Via Extrusion, Hot Rolling and Ageing

Achieving High Mechanical Performance of the Large-Scale Sand-Casting Mg–4Y–x Nd–y Gd–0.4Zr Alloys by Tailoring Nd and Gd Contents

Effect of chemical composition on the microstructure, tensile properties and fatigue behavior of sand-cast Mg–Gd–Y–Zr alloy

Microstructure and mechanical properties of as-cast Mg−8Li−xZn−yGd (x=1, 2, 3, 4; y=1, 2) alloys