Reliability Analysis of a Multi-State Repairable System

Junji Li

1992-01-01

Abstract:This paper deals with a multi-state repairable system. Under the assumption, the failure rates of the system are constant and the repairtime is subject to general distribution. The supplementary variable method is used to obtain some reliability index of the system.

What problem does this paper attempt to address?

Reliability of Multi-State Systems with Free Access to Repairable Standby Elements

Gregory Levitin,Heping Jia,Yi Ding,Yonghua Song,Yuanshun Dai

DOI: https://doi.org/10.1016/j.ress.2017.05.003

IF: 7.247

2017-01-01

Reliability Engineering & System Safety

Abstract:The paper presents an approach for evaluating reliability of standby systems composed of multi-state elements with constant state transition rates. Any standby elements can be repaired, whereas no repairs are possible in operation. When an operating element fails the standby element with the best technical state is activated. Time-to-failure distributions of operating elements depend on their states at the time of activation. An iterative algorithm for reliability evaluation based on element state probabilities is suggested. An example of using the algorithm for evaluating reliability of standby system is presented.
Redundancy analysis for repairable multi-state system by using combined stochastic processes methods and universal generating function technique

Anatoly Lisnianski,Yi Ding

DOI: https://doi.org/10.1016/j.ress.2009.05.006

IF: 7.247

2009-01-01

Reliability Engineering & System Safety

Abstract:This paper discusses a type of redundancy that is typical in a multi-state system. It considers two interconnected multi-state systems where one multi-state system can satisfy its own stochastic demand and also can provide abundant resource (performance) to another system in order to improve the assisted system reliability. Traditional methods are usually not effective enough for reliability analysis for such multi-state systems because of the “dimensional curse” problem. This paper presents a new method for reliability evaluation for the repairable multi-state system considering such kind of redundancy. The proposed method is based on the combination of the universal generating function technique and random processes methods. The numerical example is presented to illustrate the proposed method.
Reliability analysis of a discrete-time one-unit repairable system with delay repair

YANG Yi,WANG Li-chao,ZOU Yun

DOI: https://doi.org/10.3321/j.issn:1001-506x.2008.05.052

2008-01-01

Abstract:A model is proposed for a discrete-time one-unit repairable system with delay repair.It is supposed that the system has three states: normal,repair and waiting repair,and that the system life,repair time and waiting repair time all have general distribution.Using the method of stochastic process,the relation of system states is investigated,and a series of reliability indices are obtained such as reliability,availability,and the mean failure times.Finally,two examples are given to illustrate the proposed model.
Reliability Analysis of Discrete-time One-unit Repairable System

YANG Yi,WANG Li-chao,ZOU Yun

DOI: https://doi.org/10.3969/j.issn.1005-9830.2008.04.002

2008-01-01

Abstract:The time parameter is assumed to be discrete as there are many discrete-time problems in engineering community,but the existing theory only gives us methods in continuous-time systems.Considering the one-unit discrete time repairable systems,this paper proposes a state transition model based on failure rate and repairable rate.The reliability performances such as reliability,availability of the system and the mean failure times are obtained.An example is given to illustrate the effectiveness of the proposed model.
Reliability And Inspection Policies Study Of Repairable System With N Kinds Of Repairmen

Liying Wang,Jinxiang Wei,Youtong Fang

2007-01-01

Abstract:This paper considers the reliability and inspection policies of a repairable system. The system has four models-normal, abnormal, hidden fault and failure. Normal, abnormal, hidden fault are working models. When the system is operating, it is inspected once every random period to know which working model is the system in. The diagnostic result for normal and abnormal may be wrong. When system is in hidden fault, diagnostic result is correct. After the system fails, it can be repaired by one of N kinds of repairmen according to the fault's situation. When the result of inspection is that the system is in normal or abnormal models it will accept preventive maintenance. Under the assumption that failure time is arbitrary continuous distribution and inspection interval time is exponential distribution, the reliability indices and the optimal inspection cycle of the system are obtained by using probability analysis and vector Markov process method. Researches on the result of numeral example indicate the feasibility of the proposed method.
Reliability analysis of repairable multi-state system with common bus performance sharing

Huan Yu,Jun Yang,Huadong Mo

DOI: https://doi.org/10.1016/j.ress.2014.07.017

IF: 7.247

2014-01-01

Reliability Engineering & System Safety

Abstract:In this paper, an instantaneous availability model for repairable multi-state system (MSS) with common bus performance sharing is proposed. The repairable MSS consists of some multi-state units and a common bus performance redistribution system. Each unit in the system has several performance levels and must satisfy its individual random demand. A unit can transmit the surplus performance to other units in real time through the common bus performance redistribution system, if it has a performance that exceeds its demand. The entire system fails if the demand of any unit is not satisfied. A new method based on the combination of the stochastic process method and the universal generating function technique is suggested to evaluate the instantaneous availability and the mean instantaneous performance deficiency of the proposed repairable MSS. Two examples are given for applications in the end.
State probability of a series-parallel repairable system with two-types of failure states

G. Levitin,T. Zhang,M. Xie

DOI: https://doi.org/10.1080/00207720600903201

IF: 2.648

2006-01-01

International Journal of Systems Science

Abstract:This paper presents a method for the analysis of a series-parallel safety-critical system where the system states can be distinguished into failure-safe and failure-dangerous. The method incorporates the Markov chain and universal generating function technique. In the model considered, both periodic inspection and repair (perfect and imperfect) of system elements are taken into account. The system state distributions and the overall system safety function are derived, based on the developed model. The proposed method is applicable to complex systems for analysing state distributions and it is also useful in decision-making such as determining the optimal proof-test interval or repair resource allocation. An illustrative example is given.
Markov Repairable Systems With History Dependent Up And Down States

Lirong Cui,Haijun Li,Jinlin Li

DOI: https://doi.org/10.1080/15326340701645983

2007-01-01

Stochastic Models

Abstract:This paper introduces a Markov model for a multi-state repairable system in which some states are changeable in the sense that whether those physical states are up or down depends on the immediately preceding state of the system evolution process. Several reliability indexes, such as availability, mean up time, and steady-state reliability are calculated using the matrix method. A sufficient condition under which the availabilities of the stochastically monotone repairable systems with history-dependent states can be compared is also obtained. Some examples are presented to illustrate the results in the paper.
Reliability Analysis of Standby Systems with Multi-State Elements Subject to Constant Transition Rates.

Heping Jia,Gregory Levitin,Yi Ding,Yonghua Song

DOI: https://doi.org/10.1002/qre.2401

2018-01-01

Quality and Reliability Engineering International

Abstract:Standby redundancy has been extensively applied to critical engineering systems to enhance system reliability. Researches on reliability evaluation for standby systems focus more on systems with binary-state elements. However, multi-state elements with different performances have played a significant role in engineering systems. This paper presents an approach for reliability analysis of standby systems composed of multi-state elements with constant state transition rates and absorbing failure states. The approach allows modelling different standby systems beyond cold, warm and hot ones by taking into account differences in possible maintenance of elements in standby and operation modes and dependence of elements' operational behavior on their initial state at the time of activation. An iterative algorithm for reliability evaluation based on element state probabilities is suggested. Illustrating examples of evaluating reliability of different types of homogeneous and heterogeneous standby systems are demonstrated.
Dynamic Reliability Assessment for Nonrepairable Multistate Systems by Aggregating Multilevel Imperfect Inspection Data.

Yu Liu,Chu-Jie Chen

DOI: https://doi.org/10.1109/TR.2016.2645840

IF: 5.883

2017-01-01

IEEE Transactions on Reliability

Abstract:Traditional time-based reliability assessment methods compute reliability measures of a multistate system (MSS) purely based upon historical time-to-failure data collected from a large population of identical systems. Using these methods, one can only assess the reliability of a system from a population or statistical perspective. Moreover, these methods fail to characterize the stochastic behavio...
Multistate System Reliability Assessment by Using the Markov Reward Model

Anatoly Lisnianski,Ilia Frenkel,Lev Khvatskin,Yi Ding

DOI: https://doi.org/10.1007/978-0-8176-4619-6_12

2008-01-01

Abstract:The chapter considers reliability measures for a multistate system where the system and its components can have different performance levels, ranging from perfect functioning tip to complete failure. The general approach is suggested for computation of commonly used reliability measures. According to the approach, the general Markov reward model should be built, so that different reliability measures can be calculated by the corresponding reward matrix determination. A numerical example is presented in order to illustrate this approach.
Reliability Analysis of A Repairable System with Repairmen Selected Randomly

Guo Lina,Tao Youde,Xu Houbao,Gao Chao

2010-01-01

Abstract:In this paper, we deal with a repairable system with repairmen whom can be selected randomly. In reliability study, it is ordinary to substitute the steady-state reliability indices for dynamic ones because the time-dependent solution is difficult to get. But this replacement should be based on some conditions in general. Therefore it is important to study the unique existence and the expression of the dynamic solution and it is the same with its stability. This paper is devoted to studying the unique existence of the dynamic solution of the system by C-0-semigroup theory and discussing its exponential stability by analyzing the spectra distribution of the system operator and its quasi-compactness. Some reliability indices of the system are discussed with a different method from traditional one, which is simpler when considering the steady-state indices.
A Systematic Approach to the Reliability Analysis of an N-Unit Warm Standby System with K-Repair Facility

Yu Pang,Hong-Zhong Huang,Yu Liu,Min Xie

DOI: https://doi.org/10.1115/detc2009-86995

2009-01-01

Abstract:A systematic reliability analysis of n-unit warm standby repairable system with k-repair facility is presented in this paper. Traditional approaches are extended under the following assumptions: (1) the working lifetime, the standby lifetime, and the repair time of failed units are represented as exponential distribution; and (2) the repair of failed units are as good as new after repair. In this paper, a general reliability analysis of an n-unit warm standby repairable system with k-repair facility is presented. Based on previous analysis, the steady-state reliability and the average availability of the system are formulated using the Markov process theory and Laplace transform.
Reliability analysis of a repairable parallel system with repair time omission

Yu Pang,Hong-Zhong Huang,Yu Liu,Qiang Miao

DOI: https://doi.org/10.1109/ICRMS.2009.5270242

2009-01-01

Abstract:Based on some practical problems in industrial engineering, a species of two-unit parallel repairable system model is introduced in this paper. The prominent feature of the model is described as follows: if a repair time is sufficiently short (less than some threshold value) that does not affect the system operation, i.e. the effect could be ignored, the system can be considered as being operating during this repair time. Two scenarios are discussed where the threshold value is regarded as a constant and non-negative random variable, respectively. Reliability indices such as instantaneous availability are formulated.
Redundancy Analysis for Multi-state System: Reliability and Financial Assessment

Anatoly Lisnianski,Yi Ding

DOI: https://doi.org/10.1007/978-0-8176-4971-5_11

2010-01-01

Abstract:This paper discusses a type of redundancy that is typical in a multi-state system. It considers two interconnected multi-state systems where one multi-state system can satisfy its own stochastic demand and also can provide abundant resource (performance) to another system in order to improve the assisted system reliability. The paper also considers the financial issue for such a system where satisfied demand is associated with financial benefit and unsatisfied demand is associated with penalty. Traditional methods are usually not effective enough for such multi-state systems because of the "dimensional curse" problem. This paper presents the method for evaluation of reliability and corresponding financial issue for multi-state system with such kind of redundancy. The proposed method is based on the special type of universal generating function universal generating function associated with discrete-state continuous-time stochastic process. The numerical example is presented to illustrate the proposed method.
Reliability assessment for multi-state systems under a dynamic load-sharing strategy

Xiaohu Zhang,Renqiang Xiu,Chujie Chen,Yu Liu

DOI: https://doi.org/10.1109/QR2MSE.2013.6625603

2013-01-01

Abstract:In this paper, a multi-state system under dynamic load-sharing strategy is studied. The system is consisting of more than one type of components connected in parallel. The performance rate of the component can be increased or decreased, leading to a change of failure rate. Once any component in the system fails, the performance rate of components will be redistributed based on a dynamic load-sharing strategy. The Markov model is used in this paper to characterize the deterioration process of the system and evaluate the system reliability. The proposed model is demonstrated via a numerical example.
Numerical Analysis Of A Reparable Multi-State Device

Houbao Xu,Weiwei Hu

DOI: https://doi.org/10.1109/ASCC.2013.6606132

2013-01-01

Abstract:A numerical scheme is formulated for approximating the dynamic behavior of a reparable multi-state device, which can be described as a distributed parameter system of coupled partial and ordinary hybrid equations. The convergence issues are established by applying the Trotter-Kato Theorem, and simulation results show the effectiveness of the proposed scheme.
Reliability analysis of Markov history-dependent repairable systems with neglected failures

Shijia Du,Zhiguo Zeng,Lirong Cui,Rui Kang

DOI: https://doi.org/10.1016/j.ress.2016.10.030

IF: 7.247

2017-01-01

Reliability Engineering & System Safety

Abstract:Markov history-dependent repairable systems refer to the Markov repairable systems in which some states are changeable and dependent on recent evolutional history of the system. In practice, many Markov history-dependent repairable systems are subjected to neglected failures, i.e., some failures do not affect system performances if they can be repaired promptly. In this paper, we develop a model based on the theory of aggregated stochastic processes to describe the history-dependent behavior and the effect of neglected failures on the Markov history-dependent repairable systems. Based on the developed model, instantaneous and steady-state availabilities are derived to characterize the reliability of the system. Four reliability-related time distributions, i.e., distribution for the k th working period, distribution for the k th failure period, distribution for the real working time in an effective working period, distribution for the neglected failure time in an effective working period, are also derived to provide a more comprehensive description of the system's reliability. Thanks to the power of the theory of aggregated stochastic processes, closed-form expressions are obtained for all the reliability indexes and time distributions. Finally, the developed indexes and analysis methods are demonstrated by a numerical example.
Multi-state Reliability Modeling and Analysis of Reconfigurable Manufacturing Systems

DUAN Jianguo,LI Aiping,XIE Nan,XU Liyun

DOI: https://doi.org/10.3901/jme.2011.17.104

2011-01-01

Abstract:To solve the problem that there is combination problem when multi-state system reliability model is formulated by traditional methods,the multi-state reliability model of Reconfigurable manufacturing system(RMS) is built based on the stochastic process and the universal generating function(UGF) technique.In order to get all the steady-state probability,the Markov process model of reconfigurable machine tool(RMT) with the characteristic of non-adjacent state transition is established.Through defining the buffer states and analysing the influence of buffer states on the machine availability,both the buffer availability and the actual steady-state probability are obtained.According to the characteristics of RMS and RMT,UGF technique is perfected,and by which generating functions of machine level and system level are expressed followed by the establishment of multi-state reliability model of repairable RMS for multi-parts family.Furthermore,the performance indexes of RMS are also discussed.A parallel-serial hybrid machining system with four stages for double-parts family composed of cylinder heads is taken as an example to verify the effectiveness of the model and the validity of the analysis method.
On the Use of the Importance Measure for Multi-State Repairable k-out-of-n: G Systems

hongyan dui,shubin si,zhiqiang cai,shudong sun,yingfeng zhang

DOI: https://doi.org/10.1080/03610926.2012.685549

2014-01-01

Abstract:Importance measures in reliability systems are used to identify weak components in contributing to proper functioning of the system. Traditional importance measures mainly concern the change of the system reliability as the change of the reliability of one component and seldom consider the expected number of repairs of the objective component in unit time. This paper proposes an improvement potential rate importance (IPR) to verify the effectiveness of the improvement in system reliability for multi-state repairable k-out-of-n: G systems. Then the comparisons between IPR and Birnbaum importance are discussed. Finally, a case study is given to demonstrate the proposed IPR.

Reliability Analysis of a Multi-State Repairable System

Reliability of Multi-State Systems with Free Access to Repairable Standby Elements

Redundancy analysis for repairable multi-state system by using combined stochastic processes methods and universal generating function technique

Reliability analysis of a discrete-time one-unit repairable system with delay repair

Reliability Analysis of Discrete-time One-unit Repairable System

Reliability And Inspection Policies Study Of Repairable System With N Kinds Of Repairmen

Reliability analysis of repairable multi-state system with common bus performance sharing

State probability of a series-parallel repairable system with two-types of failure states

Markov Repairable Systems With History Dependent Up And Down States

Reliability Analysis of Standby Systems with Multi-State Elements Subject to Constant Transition Rates.

Dynamic Reliability Assessment for Nonrepairable Multistate Systems by Aggregating Multilevel Imperfect Inspection Data.

Multistate System Reliability Assessment by Using the Markov Reward Model

Reliability Analysis of A Repairable System with Repairmen Selected Randomly

A Systematic Approach to the Reliability Analysis of an N-Unit Warm Standby System with K-Repair Facility

Reliability analysis of a repairable parallel system with repair time omission

Redundancy Analysis for Multi-state System: Reliability and Financial Assessment

Reliability assessment for multi-state systems under a dynamic load-sharing strategy

Numerical Analysis Of A Reparable Multi-State Device

Reliability analysis of Markov history-dependent repairable systems with neglected failures

Multi-state Reliability Modeling and Analysis of Reconfigurable Manufacturing Systems

On the Use of the Importance Measure for Multi-State Repairable k-out-of-n: G Systems