Abstract:The next generation autonomous sensor nodes are being developed towards ultra-low-power with on-node signal processing capability. The former facilitates battery-less and miniaturized sensors relying on harvested energy, while the latter enables intelligent System-on-Chip (SoC) to sense and process multimodal parameters locally on the sensor nodes. As for analog front-end (AFE), a straightforward solution for low power and digital compatibility is to reduce its supply voltage to the sub-volt range. However, supply scaling is less friendly to conventional AFEs, which often require large dynamic range (DR) and high linearity, Furthermore, practical considerations of low noise, high input-impedance <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$(\mathrm{Z}_{\text{in}})$</tex> and sensor-dependent bandwidth (BW) further exacerbate the challenges to comply with versatile sensors. To realize the low-voltage AFE, time-domain (TD) direct digitization architectures [1]–[5] were proposed (Fig. 1). The <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$\mathrm{G}_{\mathrm{m}}-\mathrm{C}$</tex> based delta-sigma modulator <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$(\Delta\Sigma \mathrm{M})$</tex> with a built-in TD loop filter benefits from high input impedance and higher order noise shaping [1], but the <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$\mathrm{G}_{\mathrm{m}}$</tex> exhibits nonlinearity for a large input signal. Alternatively, the VCO-based AFEs provide better supply voltage scalability and inherent <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">${1}^{\text{st}}$</tex> -order noise shaping. The open-loop VCO-based AFE [2] benefits from a small chip area, but suffering from the tradeoff between linearity and input range. While the closed-loop VCO-based AFE solves this issue [3]–[5], this topology often needs a highly linear feedback DAC that notably reduces the input impedance of the AFE, unless impedance boosting buffers are used [6]. Besides, the closed-loop VCO based AFEs needs to be clocked continuously, resulting in power overhead.

Analog Front-End Design for Mobile and Multimedia SoC

Design of rf front end for cavity beam position monitor based on ics *

A 20 Μw Dual-Channel Analog Front-End in 65nm CMOS for Portable ECG Monitoring System

Interface Design for Analog Front-End Chips in Battery Management Systems

SoC-oriented Design Methodology of Digital Audio Decoding System

A Low Power Low Noise Analog Front End for Portable Healthcare System

A Common Architecture for Digital Process of Ultrasonic Imaging System after AFE

A 0.8V/0.6V 2.2μW Time-Domain Analog Front-End with <tex>$540\text{mV}_{\text{pp}}$</tex> Input Range, 81.6dB SNDR and <tex>$80\mathrm{M}\Omega$</tex> Input Impedance

Low Power Digital Design for Mobile Computing

Design of an efficient digital front-end for audio delta-sigma digital-to-analog converter

Design and signal optimization of analog front end of EMCCD

Offset-free DC-coupled Analog Frontend Circuit for High-Dynamicrange Signals

Design of a Digital Front End in All-Digital Quadrature-Transmitter

The Analog Front-end Prototype Electronics Designed for LHAASO WCDA

Si 3 N 4 -Based Integrated Optical Analog Signal Processor and Its Application in RF Photonic Frontend

An AC Coupling Ultrasound Analog Front-End Architecture with A Three-stage DCOC

High Performance Analog Front End AD7714 and Its Applications

A 2.5-V 56-Mw Baseband Chain in a Multistandard TV Tuner for Mobile and Multimedia Applications

An Efficient Digital Front-End for 16-Bit Audio Delta-Sigma D/A Converter

A 0.8 V, 14.76 nVrms, Multiplexer-Based AFE for Wearable Devices Using 45 nm CMOS Techniques

Design of an Analog Front-End for Ambulatory Biopotential Measurement Systems