Abstract:The environmental concerns associated with artificially formulated engine oils have forced a shift towards bio-based lubricants. The deposition of hard coatings on engine components and migrating to environmentally friendly green lubricants can help in this regard. Chemically modified forms of vegetable oils, with better low-temperature characteristics and enhanced thermo-oxidative stability, are suitable substitutes to conventional lubricant base oils. The research presented in this manuscript was undertaken to experimentally investigate the wear and friction performance of a possible future generation of an environmentally friendly bio-based lubricant as a potential replacement for conventional engine lubricants. In order to quantify the tribological benefits which can be gained by the deposition of DLC coatings, (an (a-C:H) hydrogenated DLC coating and an (a-C:H:W) tungsten-doped DLC coating) were applied on the cam/tappet interface of a direct acting valve train assembly of an internal combustion engine. The tribological correlation between DLC-coated engine components, lubricant base oils and lubricant additives have been thoroughly investigated in this study using actual engine operating conditions. Two additive-free base oils (polyalphaolefines (PAO) and chemically-modified palm oil (TMP)) and two multi-additive-containing lubricants were used in this investigation. Real-time drive torque was measured to determine the friction force, detailed post-test analysis was performed, which involved the use of a specialized jig to measure camlobe wear. An optical profilometer was used to measure the wear on the tappet, high-resolution scanning electron microscopy was employed to study the wear mechanism and energy-dispersive X-ray spectroscopy was performed on the tested samples to qualitatively access the degradation of the coating. When using additive-free TMP, a low friction coefficient was observed for the cam/tappet interface. The presence of additives further improved the friction characteristics of TMP, resulting in reduced average friction torque values. A tremendous enhancement in wear performance was recorded with a-C:H-coated parts and the coating was able to withstand the test conditions with little or no delamination.

TUNGSTEN CONTAINING HYDROGENATED DLC COATINGS ON GREASE LUBRICATED HARMONIC DRIVE GEAR FOR SPACE APPLICATION

Enabling ultra-low wear and long-lived lubrication by DLC–supramolecular gel composite lubrication system under extreme contact stress

Influence of coating material on elastohydrodynamic lubrication between gear meshing interfaces based on direct coupling solution

Solid Lubricating Film/Oil or Grease Complex System Ⅱ: Tribological Properties of DLC Film Coated with Space Oils and the Related Greases

Abrasive Wear, Scuffing and Rolling Contact Fatigue of DLC-Coated 18CrNiMo7-6 Steel Lubricated by a Pure and Contaminated Gear Oil

Study on the Lubrication Mechanism of Diamond-Like Carbon Coating in Two Formulated Lubricants with Two Viscosity Grades

Tribological behavior of DLC film models in base oils: Analysis of influence of sp 3 /sp 2 ratio and hydrogen content

An Improved Modeling and Numerical Analysis Method for Tooth Surface Wear of Double-Arc Harmonic Gears

Influence of W content on tribological performance of W-doped diamond-like carbon coatings under dry friction and polyalpha olefin lubrication conditions

Lubrication Performance of Helical Gear Pair Under Dynamic Load Based on Local Involute Profile

Properties of Diamond-like Tungsten-Doped Carbon Coatings Lubricated with Cutting Fluid

Synergistic Effect of Elliptic Textures and H-DLC Coatings for Enhancing the Tribological Performance of CuAl10Fe5Ni5 Valve Plate Surfaces

WS 2 -Ti-based solid-liquid synergetic lubricating coating with super-high wear resistance for space application

Friction Performance of Wc-Co Coating with Lithium Grease and Water Lubrication

Vacuum tribological properties in Cr-doped H-DLC self-lubricating radial spherical plain bearings

The Impact of Dopants (B, H) on the Mechanical Behavior and Tribological Performance of DLC Film under Water Lubrication

Friction and Wear Performance Evaluation of Bio-Lubricants and DLC Coatings on Cam/Tappet Interface of Internal Combustion Engines

Investigation of the Friction Behavior of Harmonic Drive Gears at Low Speed Operation

Integrated wear prediction model for cylindrical gear with variable hyperbolic circular arc tooth trace under mixed elastohydrodynamic lubrication

Scuffing Resistance of 16MnCr5 HCR TiAlCN-Coated Gears

Structural and environmental dependence of superlubricious properties in hydrogenated Graphite-Like carbon Films: Implications in solid state lubrication