Abstract:For the manufacturing of Si-based semiconductors, CMP is utilized extensively to enable FEOL process integration such as STI, deep-trench, ILD, and poly-open. Silica slurries are usually adopted for bulk oxide polish while ceria slurries are more suited for the final “buff” polish where high selectivity to nitride is required. The ever stringent requirement for scratch reduction leads to the trend of using nano-sized abrasive particles in all types of CMP slurries. However, the stronger adhesion force between these nanoparticles and wafer surface necessitates the re-design and optimization of post-CMP processes to meet the low PR/FM defect requirement. The selection of proper chemicals is often the first step towards post-CMP cleaning. However, design of cleaning sequence, exploitation of the tool hardware, and optimization of operating parameters are equally critical to achieve maximum cleaning efficiency. As shown in Fig. 1, for an oxide or poly-Si CMP process with an acidic silica-based slurry, a preferred post cleaning process should operate in alkaline environment (e.g., pH 8~10) in order to build in repulsive zeta potential for easy of particle removal from wafer surface. In this case, the use of an acidic pCMP chemical would be unfavorable from zeta-potential point of view. Replacement of acidic chemical with just DIW (pH ~ 7) leads to significant reduction in PR/FM. In addition, optimization of the directionality, spin rpm, arm oscillation speed...etc, helps eliminate the wafer center-heavy signature and reduces the defect count further down. For FEOL CMP with ceria-based slurry running on a 3-platen polisher with serial meg tank/brush cleaning module, one can design the pCMP process based on the unique “reactive” nature of ceria abrasives, and also fully exploit the available hardwares and their process parameters. In this example, the POR process adopts only DIW in the meg tank. The go-to process, however, replaces DIW with a diluted acidic oxidizer so as to neutralize the reactive ceria abrasives, making it much easier to dislodge the particles from oxide wafer surface. The significant FM NADD reduction with the go-to pCMP process illustrates the efficiency of adding the meg clean step with diluted oxidizer. Further PR/FM reduction can be realized by optimizing the hardware and machine parameters such as those listed in Fig. 2, from on-platen buff clean all the way to the terminal step of Maragoni drying. Furthermore, for a new pCMP process to be considered production-ready, run order effects, repeatability, and CoO reduction need to be taken into account as well. In addition, post-clean surface analyses are carried out to ensure no potential reliability concern. Reference: W.-T. Tseng, J. Hagan, K. Mohan, R. Hull, J. MacDougall, R. Murphy, L. Tai, S. Molis, “ Post Cleaning and Defect Reduction for Tungsten Chemical Mechanical Planarization ” ICPT, 2015. Figure 1

Improving the Environmental Performance of in Situ PECVD Chamber Cleaning Processes by Studies of CVD Reactor Clean Performance and Field Evaluation of Optimised Processes

In-situ Chamber Clean for Chromium Etch Application

Eco-Friendly Dry-Cleaning and Diagnostics of Silicon Dioxide Deposition Chamber

Growth, trapping and abatement of dielectric particles in PECVD systems

Use of plasma process diagnostic sensors for the monitoring of in situ dry cleaning of plasma enhanced chemical vapor deposition chamber

Achievement of Green and Sustainable CVD Through Process, Equipment and Systematic Optimization in Semiconductor Fabrication

Post Cleaning for FEOL CMP with Silica and Ceria Slurries

Reduction of Greenhouse Gas Emissions by Metal Interconnect Etch Process Optimization

Use of 2H-heptafluoropropane, 1-iodoheptafluoropropane, and 2-iodoheptafluoropropane for a high aspect ratio via etch in a high density plasma etch tool

Technological suitability and improvement for shaping environmental performance: A life cycle perspective on Fenton-based wastewater treatment processes

Improved performance of parallel surface/packed-bed discharge reactor for indoor VOCs decomposition: optimization of the reactor structure

Optimization of approach for metal contamination reduction

Survey of Activated Cleaning Chemistries for Low-Stress Post-Chemical Mechanical Planarization Cleaning of Silicon Carbide

Reducing the environmental impact of semiconductor manufacture

Effect of Structure to Promote Organic Residue Removal during Cu Post-Chemical Mechanical Planarization (p-CMP) Cleaning

Scalable Gas Diffusion Electrode Fabrication for Electrochemical CO2 Reduction Using Physical Vapor Deposition Methods.

A Novel Flameless Oxidation and In-Chamber Melting System Coupled with Advanced Scrubbers for a Laboratory Waste Plant.

21St CIRP Conference on Life Cycle Engineering Material and Energy Efficiency Analysis of Low Pressure Chemical Vapor Deposition of TiO 2 Film

Optimization of Inlets and Outlets of an ALD Chamber with Radiant Heating

Study and Optimization of Room Temperature Inductively Coupled Plasma Etching of Inp Using Cl-2/Ch4/H-2 and Ch4/H-2

Study on productivity and aerosol emissions of magnetic field-assisted EDM process of SiC p / Al composite with high volume fractions