Abstract:Micro-interconnection copper pillar bumps are being widely used in the packaging areas of memory chip and high performance computer due to their high density, good conductivity and low noise. Studying the interfacial behavior of copper pillar bump is of great significance for understanding its failure mechanism and microstructure evolution in order to improve the reliability of flip chip package. The thermoelectric stress test, in-situ monitor, infrared thermography test, and microstructure analysis method are employed to study the interfacial reaction, life distribution, failure mechanism and their effect factors of Cu/Ni/SnAg1.8/Cu flip chip copper pillar interconnects under 9 groups of thermoelectric stresses including 2104-3104 A/cm2 and 100-150°C. Under thermoelectric stresses, the interfacial reaction of Cu pillar can be divided into three stages:Cu6Sn5 growth and Sn solder exhaustion; the Cu6Sn5 phase transformation, exhaustion and the Cu3Sn phase growth; voids formation and crack propagation. The rate of Cu6Sn5 phase transforming into Cu3Sn phase is positively correlated with the current density. There are four kinds of failure modes including Cu pad consumption, solder complete consumption and transformation into Cu3Sn, Ni plating layer erosion and strip voids. An obvious polar effect is observed during the dissolution of Cu pads on the substrate side and the Ni layer on the Cu pillar side. When Cu pad is located at the cathode, the direction of electron flow is the same as that of the heat flow, and it can accelerate the consumption of Cu pad and the growth of Cu3Sn. When Ni layer serves as the cathode, the electron flow can enhance the consumption of Ni layer. Under 150°C and 2.5104 A/cm2, the local Ni barrier layer is eroded after 2.5 h, which results in the transformation of Cu pillar on the Ni side into (Cux, Niy)6Sn5 and Cu3Sn alloy. The life of Cu pillar interconnection complies well to the 2-parameter Weibull distribution with a shape parameter of 7.78, which is a typical characteristic of cumulative wear-out failure. The results show that the intermitallic growth behavior and failure mechanism at Cu pillar interconnects are significantly accelerated and changed under thermoelectric stresses compared with the scenario under the single high temperature stress.

The Failure Mechanism of Common-Mode Chip Inductors

Al-clad Cu Bond Wires for Power Electronics Packaging: Microstructure Evolution, Mechanical Performance, and Molecular Dynamics Simulation of Diffusion Behaviors

Analysis On The Causes Of Decline Of Mlcc Insulation Resistance

Functional Degradation of Nizncu-Based Multilayer Chip Inductors During Nickel Electroplating

Degradation in Electrothermal Characteristics and Failure Mechanism of SiC JBS with Different Die Attach Materials under 300°C Power Cycle Stress

Direct current-voltage failure in lead magnesium niobate-based multilayer ceramic capacitors

Failure Mechanism of Nickel-Chromium thin Film Chip Resistors

Reliability and failure analysis of fine copper wire bonds encapsulated with commercial epoxy molding compound

Competitive Failures Decoupling and Mechanisms Analysis of SiC MOSFET Module Under Power Cycling Stress

An investigation on the on dielectric, ferroelectric properties and failure mechanism for the 0805X7R multi-layer ceramic capacitor

Thermal Design, Analysis and Verification of Chip-Level MCM with Properties of Semiconductor Materials

Failure Mechanism of a Low‐Temperature‐Cofired Ceramic Capacitor with an Inner Ag Electrode

Interfacial reaction and failure mechanism of Cu/Ni/SnAg1.8/Cu flip chip Cu pillar bump under thermoelectric stresses

Thermomigration-induced failure in ball grid array solder joint under high current stressing

Reliability analysis of Multi-Layer Ceramic Capacitors based on BaTiO3 and their Mechanism of Insulation resistance degradation

Unexpected Dual Cracks in Chip-Ceramic Substrate Interconnect: Unveiling the Mechanism Behind Simultaneous Cracking at Both the Top and Bottom of a Solder Joint

Reliability Evaluation of Carbon Nanotube Interconnect in a Silicon CMOS Environment

Study on the Interfacial IMCs Growth of Nt-Cu/in Solder Joints

A Study of the $\mu$ -Solder Joint on Ajinomoto Build-up Film Using the Solder on Pad (SOP) Process for Multi-Chip Module

Growth behavior and reliability of interfacial IMC for Sn58Bi/Cu and Sn58Bi-AlN/Cu solder joints applied in IGBT modules

Influence of Material Properties on Ruggedness Evaluation of Package Architectures for SiC Power Devices