Abstract:It is crucial to further improve the overall performance of heat exchanger tube and make it adapt to higher flux conditions. In this paper, a novel type of tube inserts, symmetrical wing longitudinal swirl generators (SWLSGs), was proposed and its thermal hydraulic performance was numerically investigated under laminar flow. The effect of four geometrical parameters (inclined angle ( φ 1 ), face angle ( φ 2 ), wing angle ( φ 3 ) and pitch (P)) was explored. The results showed the mechanisms of heat transfer augmentation for SWLSGs could be divided into two main categories. The first one was that a longitudinal swirl flow with multi-vortexes would be formed by symmetrical wings. The other one was that SWLSGs had a structure similar to a deflector, which guided the cold water in the center to scour tube wall. This study found that the variation ranges of Nu/Nu0, f/f0 , and the efficiency evaluation criterion (EEC) were 5.00–10.22, 4.05–14.20, and 0.71–1.35, respectively. Both exergy destruction of heat transfer and fluid flow increased as face angle and wing angle increased, and decreased as inclined angle and pitch increased. Exergy destruction minimization principle was adopted to optimize SWLSGs. After fitting function through artificial neural network, genetic algorithm was applied to obtain the Pareto front. The physical parameters of the compromised point on the Pareto front were φ 1 =25.6°, φ 2 =142.0°, φ 3 =13.4°, P = 64.7 mm, and EEC = 1.26. The EEC of the highest point of the ratio of the exergy destruction of heat transfer and fluid flow (REHF) was 1.48. The present work provided a new method for multi-parameter study of tube inserts, and proved that the exergy destruction as evaluation was an effective evaluation index for design and optimization.

Thermodynamic Assessment and Optimization on Louver Fin with Non-Uniform Arrangement at Different Tube Rows by Desirability Approach

Detailed Heat Transfer Measurements of Curved Fin Channels

Experimental and Numerical Investigations on Louvered Fin-and-Tube Heat Exchanger With Variable Geometrical Parameters

Numerical analysis of the flow and heat transfer characteristics of a staggered perforated louver-finned heat exchanger

Entropy generation analysis and structure optimization of rectangular finned elliptical tube heat exchangers

Effect of Inlet Flow Maldistribution on the Passage Arrangement Design of Multi-Stream Plate-Fin Heat Exchanger

Entropy Generation Analysis of Spiral Finned Tube Bundles During Heat Exchanging Process

A STUDY ON THE FINS OF HEAT EXCHANGERS FROM OPTIMIZATION OF ENTROPY GENERATION

Flow and Heat Transfer Characteristics of a Double-Tube Structure Internal Finned Tube with Blossom Shape Internal Fins

Research on the Thermal Hydraulic Performance and Entropy Generation Characteristics of Finned Tube Heat Exchanger with Streamline Tube

Assessment of the heat transfer efficiency of perforated louvered fins for improved drainage

Thermal-Hydraulic Performance and Optimization of Tube Ellipticity in a Plate Fin-And-Tube Heat Exchanger

Optimization of H-type finned tube heat exchangers with combinations of longitudinal vortex generator, dimples/protrusions and grooves by Taguchi method

Influence of Fin Arrangement on Fluid Flow and Heat Transfer in the Inlet of a Plate-Fin Heat Exchanger

Design and optimization on symmetrical wing longitudinal swirl generators in circular tube for laminar flow

Optimization of Fin Geometry in Heat Convection with Entransy Theory

Numerical investigation on fin configuration improvement of 2 K sub-atmospheric plate-fin heat exchangers for the superfluid helium cryogenic systems

Numerical analysis on heat transfer and flow resistance performances of a heat exchanger with novel perforated wavy fins

Parameters Optimization of Fin-and-Tube Heat Exchanger with a Novel Vortex Generator Fin by Taguchi Method

Numerical Investigation On The Heat Transfer Enhancement Behavior Outside Longitudinal Finned Tubes

Airside Performances of Finned Eight-Tube Heat Exchangers