K, Na and Cl co-doped TiO 2 nanorod arrays on carbon cloth for efficient photocatalytic degradation of formaldehyde under UV/visible LED irradiation

Wenyu Diao,Jun He,Qiang Wang,Xi Rao,Yongping Zhang

DOI: https://doi.org/10.1039/d0cy01918f

2021-01-01

Abstract:A photocatalytic reactor of TiO 2 nanorod arrays on carbon cloth for gaseous formaldehyde degradation.

chemistry, physical

What problem does this paper attempt to address?

Synthesis of Nano-Tio2/diatomite Composite and Its Photocatalytic Degradation of Gaseous Formaldehyde

Guangxin Zhang,Zhiming Sun,Yongwei Duan,Ruixin Ma,Shuilin Zheng

DOI: https://doi.org/10.1016/j.apsusc.2017.03.198

IF: 6.7

2017-01-01

Applied Surface Science

Abstract:The TiO2/diatomite composite was synthesized through a mild hydrolysis of titanyl sulfate. The prepared composite was characterized by X-ray diffraction, N-2 adsorption-desorption, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and UV-vis diffused reflectance spectroscopy. The results demonstrate that the anatase TiO2 nanopartilces anchored on the surface of diatomite with Ti-O-Si bonds between diatomite and TiO2. The photodegradation of gaseous formaldehyde under UV irradiation by the TiO2/diatomite composite was studied under various operating conditions, including relative humidity, illumination intensity and catalyst amount, which have significant influence on the degradation process. The TiO2/diatomite composite exhibited better photocatalytic activity than pure TiO2, which could be attributed to the favorable nanoparticles dispersibility and strong formaldehyde adsorption capacity. In addition, the composite exhibited outstanding reusability over five cycles. The TiO2/diatomite composite shows great promising application foreground in formaldehyde degradation. (C) 2017 Elsevier B.V. All rights reserved.
Photocatalytic Degradation of Gaseous Formaldehyde by Fe-Doped ZnO Nanorods Grown on Ceramic Spheres

Duan Yue-Qin,Yang Song-Po,Yu Jiang-Ling,Yuan Zhi-Hao

DOI: https://doi.org/10.11862/cjic.2014.184

2014-01-01

Abstract:Zinc oxide (ZnO) and Fe doped ZnO nanorods were fabricated on ceramic balls by a simple low cost wet-chemical route. The as-prepared samples were characterized by XRD, SEM, TEM and UV-Vis spectroscopy. Photocatalytic activities of pure ZnO and Fe doped ZnO nanorods were investigated for degradation of formaldehyde gas under UV irradiation. The results show that doped catalyst exhibits superior photocatalytic performance than that of pure ZnO nanorods and 4% Fe doping catalyst displays the optimal photoactivity. The catalyst has good stability and is easy to be recoverd. The catalytic efficiency still maintains 85% after 10 cycls.
Low Temperature Synthesis of Few-Layer Titanate Nanobelts on Ti Mesh and the Hot-Water Induced Transformations to Highly Photocatalytic Active Titania Nanorods

Rui Jiang,Wei Wen,Yu Luo,Jin-Ming Wu

DOI: https://doi.org/10.1016/j.jece.2017.08.037

IF: 7.7

2017-01-01

Journal of Environmental Chemical Engineering

Abstract:An efficient photocatalytic reactor to remove pollutants from either water or air relies on highly active photocatalytic thin films on appropriate substrates, which contribute to both light harvesting and pollutant molecules transfer. In this investigation, few-layer titanate nanobelts were deposited on metallic Ti mesh using hydrogen peroxide solution, which were then subjected to a subsequent hot water treatment to achieve crystallized titania nanorod arrays. The three-dimensional arrays of nanorods formed on Ti mesh (three layers overlapped) exhibited an exceptional high efficiency when utilized to assist photodegradation of rhodamine B in water under UV light illumination, which is 25 times that of P25 film, and even 1.3 times that of P25 nanoparticles in a slurry system. For photodegradation of phenol in water, the three-layer Ti mesh also exhibited a reaction rate constant 6.9 times that of P25 film. The reduced band gap, abundant surface hydroxyl groups, and mixed phase effects arising from the low temperature approach contribute to the high photocatalytic activity.
Activation of Carbon Cloth and Concurrent Precipitation of Titania Nanowires for Enhanced Adsorption and Photocatalysis Performance

Jin-Ming Wu,Qing-Er Zhao

DOI: https://doi.org/10.1016/j.apsusc.2020.146779

IF: 6.7

2020-01-01

Applied Surface Science

Abstract:Vertically aligned TiO2 nanowires exhibit excellent photoactivity because of the high specific surface area and increased charge separation; yet the limited adsorption capacity towards target pollutants hinders the photo catalytic degradation of pollutants in water. We report herein a mild solution approach to precipitate anatase TiO2 nanowire arrays, with a tunable thickness of 1.5-4.5 mu m, on carbon cloth to achieve simultaneously high adsorption capacity and excellent photoactivity. When compared with TiO2 nanowire arrays precipitated on metallic Ti substrates, which possess a negligible adsorption capacity, TiO2 nanowires loaded on the activated carbon cloth substrates exhibit a higher efficiency towards photocatalytic degradations of both rhodamine B dye molecules and colorless sulfosalicylic acid in water under UV light illumination. The increasing film thickness is more effective to increase the photoactivity of TiO2 nanowires loaded on the activated carbon cloth than those on metallic Ti foil. The current investigation establishes the feasibility to greatly improve the photoactivity of one-dimensional nanostructured TiO2 arrays by using a highly adsorptive substrate.
Highly Active Amino-Fullerene Derivative-Modified TiO2 for Enhancing Formaldehyde Degradation Efficiency under Solar-Light Irradiation

Jingbiao Fan,Tao Wang,Bo Wu,Chunru Wang

DOI: https://doi.org/10.3390/nano12142366

IF: 5.3

2022-07-11

Nanomaterials

Abstract:Formaldehyde (HCHO) is a ubiquitous indoor pollutant that seriously endangers human health. The removal of formaldehyde effectively at room temperature has always been a challenging problem. Here, a kind of amino-fullerene derivative (C60-EDA)-modified titanium dioxide (C60-EDA/TiO2) was prepared by one-step hydrothermal method, which could degrade the formaldehyde under solar light irradiation at room temperature with high efficiency and stability. Importantly, the introduction of C60-EDA not only increases the adsorption of the free formaldehyde molecules but also improves the utilization of sunlight and suppresses photoelectron-hole recombination. The experimental results indicated that the C60-EDA/TiO2 nanoparticles exhibit much higher formaldehyde removal efficiency than carboxyl-fullerene-modified TiO2, pristine TiO2 nanoparticles, and almost all other reported formaldehyde catalysts especially in the aspect of the quality of formaldehyde that is treated by catalyst with unit mass (mHCHO/mcatalyst = 40.85 mg/g), and the removal efficiency has kept more than 96% after 12 cycles. Finally, a potential formaldehyde degradation pathway was deduced based on the situ diffuse reflectance infrared Fourier transform spectrometry (DRIFTS) and reaction intermediates. This work provides some indications into the design and fabrication of the catalysts with excellent catalytic performances for HCHO removal at room temperature.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
Single-crystalline Rutile TiO2 Nanorod Array on Flexible Ti Substrates for Efficient Photoelectrocatalytic Degradation of Phenol in Water

Juan Xie,Wei Wen,Rui Jiang,Jin-Ming Wu

DOI: https://doi.org/10.1016/j.tsf.2020.138494

IF: 2.1

2021-01-01

Thin Solid Films

Abstract:Single-crystalline nanorods are intrinsic highways for charge transfer and hence ideal nanofeatures for efficient photoelectrochemical (PEC) degradations of pollutants in wastewater. Photocatalytic thin films on flexible substrates avoid the nuisance catalysts-recovering procedure and also allow for the flexible design in photo catalytic apparatus. We therefore directly deposited single-crystalline rutile TiO2 nanorod arrays on flexible and conductive Ti substrates through a hydrothermal technique and optimized the synthetic parameters to achieve an extremely high PEC activity towards phenol removal in water under UV light illumination. In the presence of tetrabutyltitanate (TBT) and HCl reactants under a hydrothermal environment, a balance in the erosion of the Ti substrate and the precipitation of TiO2 nanorods is found to be the key to tune the nanofeatures of the TiO2 thin films and in turn the PEC efficiency. The decreasing TBT concentration achieved a more sparsely distributed nanorod array, which significantly contributes to the PEC activity; yet too little TBT resulted in total dissolution of Ti plates. The PEC activity increased with increasing hydrothermal duration because of more loaded TiO2. The maximum reaction rate constant is 2.74 h(-1), which is 39 times that of a commercial P25 TiO2 nanoparticulate film. The photocurrent stabilized at 0.9 mA/cm(2) under the illumination of AM1.5G simulated solar light, suggesting a high separation efficiency of photogenerated holes and electrons along the single-crystalline rutile TiO2 nanorod arrays.
A Comparative Study on Photocatalytic Activity of Titania Nanowires Subjected to High-Temperature Calcination and Low-Temperature HCl Treatment

Jing Sun,Jin-Ming Wu

DOI: https://doi.org/10.1166/sam.2013.1486

2013-01-01

Science of Advanced Materials

Abstract:Titania thin films with ordered nanostructures offer combined advantages of high specific surface area and favorable charge separation, which are key points for efficient photocatalytic degradation of organic pollutants in water or atmosphere. In this paper, titania nanowire arrays were fabricated on titanium plates using a hydrogen peroxide solution, which were then subjected to a subsequent HCl treatment at a low temperature of 80 degrees C to achieve crystallized nanorod arrays. The nanorod array was characterized in detail by electron microscopy, X-ray diffraction, and various spectroscopic techniques, in comparison with the nanowire array after a high temperature calcination in air atmosphere to induce crystallization. The array efficiency in assisting photodegradation of rhodamine B in water under the UV-Vis irradiation was studied in relation to the relevant structural parameters. It is found that the low-temperature-deposited nanorod array exhibited a photocatalytic activity superior to that of the calcinated nanowire array. The enhanced efficiency has been attributed to the reduced band gap, a higher density of surface hydroxyl groups and the coexistence of anatase and rutile in the film.
Photocatalytic Degradation Kinetics of Gaseous Formaldehyde Flow Using TiO2 Nanowires

Hailong Dou,Dan Long,Xi Rao,Yongping Zhang,Yumei Qin,Feng Pan,Kai Wu

DOI: https://doi.org/10.1021/acssuschemeng.8b06463

IF: 8.4

2019-01-01

ACS Sustainable Chemistry & Engineering

Abstract:A high-performance TiO2 nanowire photocatalyst was successfully prepared by a hydrothermal method to decompose gaseous formaldehyde into CO2 and H2O in a homemade tube reactor without secondary pollution under ultraviolet irradiation. The photocatalytic oxidization kinetics fits well with the traditional Langmuir Hinshelwood Hougen Watson model. Multiple parameters, including the formaldehyde concentration, flow rate, and light intensity, were monitored online and proved to be key factors affecting the rate of the photocatalytic reactions. The crystallinity of the photocatalyst and its surface reactive site density determined the adsorption equilibrium constant (K-HCHO) of formaldehyde on TiO2. The experimental results show that the degradation kinetics of mobile gas-phase formaldehyde by TiO2 nanowires did not strictly conform to the first-order reaction kinetics, and its photocatalytic degradation rate increases with an increase in ultraviolet light emitting diode irradiation intensity. It takes only 8.6 min to completely degradate formaldehyde at a flow rate of 50 mL/min with 50 mg of 700TiO(2), and the reaction performance remains unchanged during the 1200 min duration of the decomposing process.
Composite nanofiber membrane embedded TiO 2 /diatomite catalyst for highly efficient mineralization of formaldehyde

Fang Yuan,Renfeng Yang,Bin Wang,Ying Gao,Chunquan Li,Zhiming Sun

DOI: https://doi.org/10.1016/j.seppur.2023.123423

IF: 8.6

2023-02-21

Separation and Purification Technology

Abstract:The application potential of fine powder photocatalysts could be effectively improved by preparing membranes to form large-scale photocatalytic materials. Herein, a composite nanofiber membrane embedded with TiO 2 @diatomite catalyst was prepared with a simple electrospinning-spraying process for formaldehyde (HCHO) photocatalytic purification. The results show that the prepared composite nanofiber membranes exhibit good photocatalytic performance toward HCHO under UV light and actual sunlight illumination, and the degradation rate is up to 1.03 times that of the membrane prepared by Degussa P25. Moreover, it has good reusability and cycling structural stability. The introduction of natural diatomite not only enhanced the HCHO removal performance with a lower preparation cost, but also improved the air permeability (avg. 86.5 mm·s −1 ) and water vapor permeability (avg. 48.5 g·m −2 ·24 h). Moreover, the influences of environmental factors, including the initial concentration of HCHO, relative humidity and environmental temperature, on the process of photocatalytic removal of HCHO are systematically investigated. Additionally, the intermediates of the photocatalytic degradation of HCHO are also obtained by in situ DRIFTS analysis, and the degradation pathway is presented accordingly. This work provides an alternative solution toward using fine powder photocatalysts to obtain large-scale photocatalytic materials and a deep insight into preparing mineral-based catalytic membranes for air purification.

engineering, chemical
Synthesis of α-Fe2O3/TiO2 nanotube arrays for photoelectro-Fenton degradation of phenol

Yanqing Cong,Zhe Li,Yi Zhang,Qi Wang,Qian Xu

DOI: https://doi.org/10.1016/j.cej.2012.03.031

IF: 15.1

2012-01-01

Chemical Engineering Journal

Abstract:Developing new nanophotocatalysts and identifying their roles are highly attractive in environmental protection and energy utilization. Photoelectro-Fenton process is an environmentally friendly technology and has a wide application in the control of environmental pollutants. However, efficient nanophotocatalysts responsive to visible light are still few. In this work, we have successfully synthesized a uniformly dispersed α-Fe2O3/TiO2 nanotubes hetero-nanostructure by electrochemical deposition method for the degradation of phenol. Compared with the separate α-Fe2O3 nanoparticles and TiO2 nanotubes, the composite α-Fe2O3/TiO2 nanotubes electrodes were more effective in the photoelectro-Fenton degradation of phenol and a 100% removal efficiency of phenol was obtained after 60min treatment. The composite α-Fe2O3/TiO2 electrodes showed an enhanced absorbance in visible light region and had good stability to photoelectro-Fenton reactions. The role of α-Fe2O3 nanoparticles in various Fenton-related processes were systematically investigated. The results indicate that α-Fe2O3/TiO2 nanotubes are promising material for pollution prevention.
One-step Fabrication of TiO2/Ti Foil Annular Photoreactor for Photocatalytic Degradation of Formaldehyde

Yumei Qin,Zining Wang,Juantao Jiang,Lingbo Xing,Kai Wu

DOI: https://doi.org/10.1016/j.cej.2020.124917

IF: 15.1

2020-01-01

Chemical Engineering Journal

Abstract:One-step hydrothermal synthesis approach is applied to prepare oriented TiO2 nanowires on a Ti foil which serves as both the substrate and Ti source. The grown TiO2 nanowires are characterized by scanning electron microscopy, transmission electron microscopy and X-ray diffractometry. The adsorption and photocatalytic performance of the TiO2/Ti foil catalyst in formaldehyde degradation has been explored in detail by a homemade setup, aiming at elucidating the photocatalytic performance of the TiO2/Ti foil catalyst as functions of the experimental preparation parameters, such as NaOH concentration, hydrothermal reaction temperature and time elapse as well as post-annealing temperature. More strikingly, the TiO2/Ti foil catalyst can be directly devised into a self-supporting annular reactor which is at least twice as efficient for the formaldehyde degradation as that based on commercial TiO2 powder catalyst. This study presents a scalable and commercially viable strategy for indoor air purification.
Formaldehyde degradation of waterborne paints over S- and C-doped titanium dioxide under visible light

Kang Yao,Weijun Meng,Qiaorong Huang,Wukang Wang,Xihong Che,Hong Fang,Ran Duan

DOI: https://doi.org/10.1088/1755-1315/1171/1/012052

2023-04-01

IOP Conference Series: Earth and Environmental Science

Abstract:Abstract Fabrication technique of S- and C-doped TiO 2 nano-particle via solvo-thermal treatments was introduced, and its appearance and crystal property were studied using transmission electron microscopy, energy-dispersive X-ray and powder X-ray diffraction. All of these characterisations gave a reasonable explanation to satisfactory doping of S and C in the anatase. The photo-catalytic oxidation was conducted in environmental chambers, together with UV-VIS spectra. The catalytically active S- and C-doped anatase was assessed via surveying the formaldehyde degradation of waterborne paints, and a removal efficiency of 93.9% in 85 min illustrated an enhanced visible-light activity.
Enhanced photocatalytic performance of visible-light-driven CuOx/TiO2-x for degradation of gaseous formaldehyde: Roles of oxygen vacancies and nano copper oxides

Yang Wang,Peng Gao,Benhang Li,Ze Yin,Li Feng,Yongze Liu,Ziwen Du,Liqiu Zhang

DOI: https://doi.org/10.1016/j.chemosphere.2021.133007

IF: 8.8

2022-03-01

Chemosphere

Abstract:Photocatalysis is an effective method for the removal of formaldehyde (HCHO), and high-efficiency visible-light-driven photocatalysts were urgently required. Herein, oxygen vacancies (OVs) and nano copper oxides (CuOx) synergistically modified TiO2 (CuOx/TiO2-x) photocatalysts were synthesized by one-step hydrothermal followed by impregnation method. The photocatalytic decomposition of HCHO reached 100% at initial concentration of 180 ppm under relative humidity (RH) = 60% by 0.1g CuOx/TiO2-x in 150 min visible light irradiation. Characterization results explored the complementary effect of OVs and CuOx systematically. The OVs increased the separation efficiency of photogenerated charge carriers and act as adsorption/active sites in HCHO photocatalytic oxidation. The moisture and O2 were adsorbed and actived by OVs to generate reactive oxygen species (ROS). After doped CuOx on the surface of TiO2-x, the photoexcited electrons in Cu2O could transfer to the conduction band (CB) of TiO2-x and the photoexcited electrons of TiO2-x could be captured by Cu nanoparticles. Therefore, more ROS were generated due to the synergistic effect of OVs and CuOx. The In-situ Fourier transform infrared (in-situ FTIR) measurements show the hydroxyl radical (•OH) was the dominant radical in HCHO photocatalytic oxidation, while •O2- could also upgrade the photodegradation efficiency of HCHO. Furthermore, the stability tests showed the degradation efficiency of HCHO still reached 90% after five recycles, indicating that CuOx/TiO2-x nanocomposites displayed a stable and high photoactivity in volatile organic compounds (VOCs) decomposition.

environmental sciences
Synergistic Effects of Multitype Carbon Doping and Oxygen Vacancies in TiO2/CNTs Composite Fabricated Via Nonthermal Plasma for Formaldehyde Removal.

Yujie Tan,Hui Xu,Ruchen Shu,Zhi Liu,Lijie Song,Ruina Zhang,Chuang Ouyang,Min Xia,Jianyuan Hou,Xinzhong Zhang,Yuan,Zhang Renxi

DOI: https://doi.org/10.1016/j.chemosphere.2023.139406

IF: 8.8

2023-01-01

Chemosphere

Abstract:Formaldehyde as one of the typical indoor pollutants has long been concerned as it can pose a threat to human health. TiO2/CNTs composite with oxygen vacancies and multitype carbon doping (C–TiO2/CNTs) was fabricated using nonthermal plasma for the photocatalytic degradation of formaldehyde. The maximum degradation rate of formaldehyde was 93% and 83% via the new catalyst (with 5% CNTs content) under solar and visible light, respectively. The characterization of the catalyst confirmed the in-situ multitype carbon doping and oxygen vacancies: interstitial carbon doping and oxygen vacancies could dramatically reduce the bandgap and contribute to the improved absorption capability of formaldehyde and electrons. Interfacial carbon doping in the form of C–O–Ti bonds provided a migration channel, whereby photogenerated electrons could efficiently transfer from CNTs to TiO2 and then quench the holes left in the VB of TiO2. Therefore, the multitype carbon doping and oxygen vacancies can expand the light response as well as promote the separation of photo-generated electron/hole pairs. EPR results and experiment section indicated that O2·− plays the most significant role in formaldehyde removal due to the reverse transfer of the electrons. This work advances the understanding of photo-degradation of TiO2/CNTs composite and provides a new route for the abatement of formaldehyde.
Photocatalytic degradation performance of gaseous formaldehyde by Ce-Eu/TiO2 hollow microspheres: from experimental evaluation to simulation

Zhifang Zong,Depeng Chen,Chunxiao Zhao,Gang Tang,Yilong Ji,Hao Zhang,Zhong Lv,Wei Dong,Xiujuan Zhu

DOI: https://doi.org/10.1007/s11356-021-13112-4

IF: 5.8

2021-03-03

Environmental Science and Pollution Research

Abstract:Gaseous formaldehyde present indoors is often in low-medium concentration, as compared to that contained in manufactured products, but still poses great threat to human health. Thus, this work aims to fabricate Ce-Eu/TiO2 hollow microspheres, which showed excellent photocatalytic performance toward formaldehyde. Furthermore, photocatalytical degradation performance of Ce-Eu/TiO2 hollow microspheres toward formaldehyde was investigated. The kinetics of degradation mechanism of gaseous formaldehyde for different concentrations and different temperatures vs time were studied, and the simulation and experimental results were also compared. It was found that formaldehyde concentration had an effect on the degradation process, which was consistent with different kinetics reactions. At low concentration, the degradation rate was decided by the adsorption rate, and no accumulation of adsorbent occurred. This process was consistent with the first-order kinetics law, which was established by L-H dynamics theory and Arrhenius equation. At medium concentration, the degradation process of formaldehyde was controlled by both adsorption and photocatalysis, which was consistent with the power law model. The 3D model of formaldehyde degradation process by Ce-Eu/TiO2 hollow microspheres at different concentrations vs time was established, and the results showed that the simulation equations were in good agreement with the experimental results.

environmental sciences
Supercritical Carbon Dioxide-Assisted TiO2/g-C3N4 Heterostructures Tuning for Efficient Interfacial Charge Transfer and Formaldehyde Photo-Degradation

Yujie Tan,Ruchen Shu,Hui Xu,Lijie Song,Ruina Zhang,Chuang Ouyang,Min Xia,Jianyuan Hou,Xinzhong Zhang,Yuan,Renxi Zhang

DOI: https://doi.org/10.1016/j.jece.2023.110992

IF: 7.7

2023-01-01

Journal of Environmental Chemical Engineering

Abstract:Long exposure to formaldehyde has been a concern for causing respiratory problems and TiO2/g-C3N4 composite is a potential choice to address this issue. This study developed a supercritical carbon dioxide (ScCO2)-assisted method to fabricate TiO2/g-C3N4 composites with two distinct heterostructures. The g-C3N4 nanosheet/TiO2 nanoparticle (denoted as type 1 heterostructure) heterojunction could accelerate electron migration because of its large interfacial surface contact. The ternary TiO2{101}/g-C3N4/TiO2{001} heterojunction (denoted as type 2 heterostructure) was synthesized for the first time, further promoting the separation of photogenerated electron/hole pairs under full-spectrum irradiation because it provided an additional migration channel for photocarriers. By loading different amounts of TiO2, the heterostructures were modulated, thereby influencing the photoactivity of the composites. The TiO2/g-C3N4 composite with 58% TiO2 loading possessed the best photocatalytic performance, achieving the highest rate constant for formaldehyde degradation, approximately 7 times higher than pure bulk g-C3N4 under either visible or full-spectrum light. Under full-spectrum irradiation, the maximum decomposition rate approached nearly 100% within 90 min. The tuned heterostructures facilitated the generation of O-2(center dot-) and center dot OH, which were dominant active oxygen radicals responsible for formaldehyde removal under light irradiation. Thus, this study developed a green route to synthesize composites with tunable heterojunctions and enhanced photocatalytic activity that can be used for indoor air pollutant degradation.
Study on TiO2/g-C3N4 S-Scheme heterojunction photocatalyst for enhanced formaldehyde decomposition

Yihai Wu,Deqin Meng,Qingbin Guo,Dengzheng Gao,Li Wang

DOI: https://doi.org/10.1016/j.optmat.2022.112213

IF: 3.754

2022-04-01

Optical Materials

Abstract:Photocatalytic degradation of pollutants is one of the most environmentally friendly and energy efficient technologies. Photocatalysts with porous structures not only enhance the adsorption of pollutants by the catalyst, but also accelerate the electron transfer and enhance the photocatalytic performance due to the exposure of more active sites. In addition, the S-Scheme heterojunction photocatalyst not only reduces the rate of electron-hole pair compounding, but also maintains the redox properties of the photocatalyst and improves photocatalytic performance. In this paper, the mesoporous material TiO2/g-C3N4 S-Scheme heterojunction photocatalysts were prepared in one step by the sol-gel method using urea as a precursor. The particles of the prepared nanomaterials are between 20 and 50 nm in size and uniformly dispersed. The photodegradation efficiency of the photocatalyst for formaldehyde under visible light can reach over 85%. One-step preparation of TiO2/g-C3N4 photocatalysts by sol-gel method with simple preparation method and high yield, solving the difficulties of low yield and high requirements for temperature and environmental conditions in the preparation of g-C3N4 using urea thermal polymerisation.

materials science, multidisciplinary,optics
Deactivation and Regeneration of Pt/Tio2 Nanosheet-Type Catalysts with Exposed (001) Facets for Room Temperature Oxidation of Formaldehyde

Longhui Nie,Peng Zhou,Jiaguo Yu,Mietek Jaroniec

DOI: https://doi.org/10.1016/j.molcata.2014.02.033

2014-01-01

Abstract:Formaldehyde (HCHO) is a major indoor air pollutant and long-term exposure to HCHO may cause health problems including nasal tumors and skin irritation. Room-temperature catalytic oxidation decomposition of HCHO is considered as the most promising strategy for the removal of HCHO due to its environmental-friendly reaction conditions and energy-saving consideration. In this work, surface-fluorinated anatase TiO2 nanosheets with dominant {001} facets (FTiO2-NS) were first prepared by a hydrothermal method using Ti(OC4H9)4 and HF as precursors. Then, Pt/FTiO2-NS catalyst with 0.5wt% Pt loadings was obtained by a combined NaOH-assisted impregnation of titania with Pt precursor and NaBH4-reduction route. The catalytic activity was evaluated by catalytic oxidation decomposition of HCHO vapor at room temperature. Fluoride poisoning (F-poisoning) phenomenon of Pt/FTiO2-NS was first observed for oxidative decomposition of HCHO. The mechanism of F-poisoning is mainly due to blocking of Pt catalytic active sites by strong interactions between Pt and highly electronegative F. In order to recover the catalytic performance, a simple regeneration method for the deactivated Pt/FTiO2-NS catalysts was proposed by NaOH washing.
Raspberry-like mesoporous Co-doped TiO 2 nanospheres for a high-performance formaldehyde gas sensor

Qian Rong,Yuan Li,Shiqiang Hao,Songting Cai,Chris Wolverton,Vinayak P. Dravid,Tianyou Zhai,Qingju Liu

DOI: https://doi.org/10.1039/d0ta11695e

IF: 11.9

2021-01-01

Journal of Materials Chemistry A

Abstract:The detection of formaldehyde is closely related to human's daily life.

materials science, multidisciplinary,chemistry, physical,energy & fuels
A Two-Step Nonthermal Plasma Method to Fabricate Ag/N- Doped TiO2/CNTs for Formaldehyde Removal under Visible Light Irradiation

Yujie Tan,Luying Sun,Guicheng Wang,Ruina Zhang,Jianyuan Hou,Renxi Zhang,Weixuan Zhao

DOI: https://doi.org/10.1016/j.jclepro.2022.133507

IF: 11.1

2022-01-01

Journal of Cleaner Production

Abstract:A novel efficient catalyst called Ag/N-doped TiO2/CNTs was fabricated using a two-step method involving treatment with ammonia plasma followed by a process of hydrogen plasma reduction at a low temperature. The photocatalyst, which was composed of silver nanoparticles (AgNPs), titanium dioxide (TiO2) and 5% amount of carbon nanotubes (CNTs), achieved an adequate formaldehyde elimination rate of 95% under visible-light irradiation. A series of analytical methods was employed to investigate the advantages of the novel fabrication method. The results showed that the first step, which is the N doping of TiO2 could be particularly important for improving the photocatalytic performance because of the reduced band gap and newly formed Ti3+. Furthermore, it could assist in the anchor of AgNPs during the second step of fabrication. During the second step of hydrogen reduction process, AgNPs of smaller sizes were more homogeneously anchored on the surface of N-doped TiO2/CNTs than that of the catalysts without ammonia plasma treatment. The resulting higher level of AgNPs could aid in efficient electron transfer and significantly improve the response to visible light, considering the surface plasmon resonance effect. CNTs and AgNPs played significant roles as electron acceptors in reducing the recombination rate of photogenerated hole pairs, and moreover, this two-step plasma process could be beneficial for achieving surface and interface properties suitable for formaldehyde photodegradation. This novel approach for fabricating an efficient Ag/N-doped TiO2/CNTs has potential for application in environmental purification systems.

K, Na and Cl co-doped TiO 2 nanorod arrays on carbon cloth for efficient photocatalytic degradation of formaldehyde under UV/visible LED irradiation

Synthesis of Nano-Tio2/diatomite Composite and Its Photocatalytic Degradation of Gaseous Formaldehyde

Photocatalytic Degradation of Gaseous Formaldehyde by Fe-Doped ZnO Nanorods Grown on Ceramic Spheres

Low Temperature Synthesis of Few-Layer Titanate Nanobelts on Ti Mesh and the Hot-Water Induced Transformations to Highly Photocatalytic Active Titania Nanorods

Activation of Carbon Cloth and Concurrent Precipitation of Titania Nanowires for Enhanced Adsorption and Photocatalysis Performance

Highly Active Amino-Fullerene Derivative-Modified TiO2 for Enhancing Formaldehyde Degradation Efficiency under Solar-Light Irradiation

Single-crystalline Rutile TiO2 Nanorod Array on Flexible Ti Substrates for Efficient Photoelectrocatalytic Degradation of Phenol in Water

A Comparative Study on Photocatalytic Activity of Titania Nanowires Subjected to High-Temperature Calcination and Low-Temperature HCl Treatment

Photocatalytic Degradation Kinetics of Gaseous Formaldehyde Flow Using TiO2 Nanowires

Composite nanofiber membrane embedded TiO 2 /diatomite catalyst for highly efficient mineralization of formaldehyde

Synthesis of α-Fe2O3/TiO2 nanotube arrays for photoelectro-Fenton degradation of phenol

One-step Fabrication of TiO2/Ti Foil Annular Photoreactor for Photocatalytic Degradation of Formaldehyde

Formaldehyde degradation of waterborne paints over S- and C-doped titanium dioxide under visible light

Enhanced photocatalytic performance of visible-light-driven CuOx/TiO2-x for degradation of gaseous formaldehyde: Roles of oxygen vacancies and nano copper oxides

Synergistic Effects of Multitype Carbon Doping and Oxygen Vacancies in TiO2/CNTs Composite Fabricated Via Nonthermal Plasma for Formaldehyde Removal.

Photocatalytic degradation performance of gaseous formaldehyde by Ce-Eu/TiO2 hollow microspheres: from experimental evaluation to simulation

Supercritical Carbon Dioxide-Assisted TiO2/g-C3N4 Heterostructures Tuning for Efficient Interfacial Charge Transfer and Formaldehyde Photo-Degradation

Study on TiO2/g-C3N4 S-Scheme heterojunction photocatalyst for enhanced formaldehyde decomposition

Deactivation and Regeneration of Pt/Tio2 Nanosheet-Type Catalysts with Exposed (001) Facets for Room Temperature Oxidation of Formaldehyde

Raspberry-like mesoporous Co-doped TiO 2 nanospheres for a high-performance formaldehyde gas sensor

A Two-Step Nonthermal Plasma Method to Fabricate Ag/N- Doped TiO2/CNTs for Formaldehyde Removal under Visible Light Irradiation