Abstract:In this paper, Polyethylene Terephthalate Glycol (PETG) has been used as a novel thermoplastic thermo-responsive Shape Memory Polymer (SMP) with biocompatibility, excellent printability, cost efficiency, and transparency for the 3D/4D printing of porous structures by material extrusion. The high deformability of PETG allows for programming without an increase in temperature or the need for additional operations. This enabled the use of PETG for the Cold Programming (CP) of ordered porous shape memory structures, made possible by material extrusion printing technology. The porous samples were printed employing three patterns and two porosity percentages. The programming operation was performed at ambient temperature by applying different amounts of pre-strains under constrained and unconstrained compression modes. The constrained test was conducted using a mandrel and a matrix for exerting pure volume reduction (pure packing). The shape recovery test was accomplished above the glass transition temperature (T g ), and the fixity and recovery ratios were recorded. Employing 3D printing provided the ability to manufacture porous thermoplastic SMP structures with highly controllable pores geometry and sizes for different porosity percentages. The results showed that the combination of the uniform strain distribution in the porous structures with the help of the 3D printing process and CP on the new PETG SMP makes it possible to achieve high deformation in the glassy region, resulting in a complete shape recovery for two lozenge and vertical patterns. Among all specimens, constrained specimens by horizontal pattern had the highest fixity ratio of 90.7%. However, low fixity ratios in CP can be justified considering the existence of two stages of spring-back and structural relaxation after unloading, resulting from the elastic and viscoelastic behavior. Increasing Infill Density (ID) along with the constrained test (pure packing) improved the shape fixity. The existence of higher mechanical constraints and harsher localized deformation are speculated to be the case for this observation. Applying higher deformations (40 to 80%), for both designed tests, brought about a weakness in the shape memory performance, while it improved for 100% volume reduction.

Experimental Evaluation of Mechanical Properties, Thermal Analysis, Morphology, Printability, and Shape Memory Performance of the Novel 3D Printed PETG‐EVA Blends

Design, processing, 3D/4D printing, and characterization of the novel PETG–PBAT blends

4D-printed PLA-PETG polymer blends: comprehensive analysis of thermal, mechanical, and shape memory performances

Investigating the Effect of ABS on the Mechanical Properties, Morphology, Printability, and 4D Printing of PETG‐ABS Blends

Investigation of the Properties of Polyethylene and Ethylene-Vinyl Acetate Copolymer Blends for 3D Printing Applications

4D printing of shape memory polyethylene terephthalate glycol/thermoplastic polyurethane (PETG/TPU) blends

Assessment of Physio-Mechanical characteristics of ABS/PETG blended parts fabricated by Material Extrusion 3D printing

Feasibility Study on the Fused Filaments of Injection-Molding-Grade Poly(Ethylene Terephthalate) for 3D Printing

Poly(ethylene terephthalate) Glycol/Carbon Black Composites For 4D Printing

The feasibility of using ethylene-vinyl acetate/natural rubber (EVA/NR)-based thermoplastic elastomer as filament material in fused deposition modelling (FDM)-3D printing application

Cold programming of ordered porous PETG 4D printed by material extrusion

Mechanical, thermal, and microstructure analysis of 3D printed polyolefin elastomer-acrylonitrile butadiene styrene blends for tunable mechanical properties

POM/EVA Blends with Future Utility in Fused Deposition Modeling

Development of Thermal Resistant FDM Printed Blends. The Preparation of GPET/PC Blends and Evaluation of Material Performance

Mechanical and Electrical Properties of Polyethylene Terephthalate Glycol/Antimony Tin Oxide Nanocomposites in Material Extrusion 3D Printing

Assessment of mechanical properties and shape memory behavior of 4D printed continuous fiber-reinforced PETG composites

Preparation and Properties of Poly(ethylene glycol-co-cyclohexane-1,4-dimethanol terephthalate)/Polyglycolic Acid (PETG/PGA) Blends

Thermomechanical Material Characterization of Polyethylene Terephthalate Glycol with 30% Carbon Fiber for Large-Format Additive Manufacturing of Polymer Structures

On the Thermomechanical Behavior of 3D-Printed Specimens of Shape Memory R-PETG

Variations in the Thermomechanical and Structural Properties during the Cooling of Shape-Memory R-PETG

Influences of printing parameters on mechanical properties of recycled PET and PETG using fused granular fabrication technique