A facile synthesis of hierarchical TiO2for dye adsorption and photocatalysis

Lu-Lu Lai,Jin-Ming Wu

DOI: https://doi.org/10.1039/c4ra04790g

2014-01-01

RSC Adv.

Abstract:Hierarchical flower-like H2Ti5O11·3H2O assembled with radial nanowires was fabricated through a template-free solution-based method, which could be converted to TiO2with controllable morphologies and phases by a subsequent acid-treating or annealing process.

What problem does this paper attempt to address?

A facile synthesis of hierarchical TiO2 for dye adsorption and photocatalysis

lulu lai,jinming wu

DOI: https://doi.org/10.1039/c4ra04790g

IF: 4.036

2014-01-01

RSC Advances

Abstract:Hierarchical flower-like H2Ti5O11 center dot 3H(2)O assembled with radial nanowires was fabricated via a template-free solution-based reaction, and was converted to TiO2 with distinct phases and morphologies by the subsequent acid-treating or annealing. The HCl treatment achieved the controllable conversion from titanate nanowires to rutile nanorods by varying the temperature and acidity. When compared with the as-synthesized titanate nanowires and the thoroughly transformed rutile nanorods, their mixtures were found to exhibit the best dye adsorption ability towards rhodamine B and methylene blue in water. The H2Ti5O11 center dot 3H(2)O nanowires decomposed in sequence to anatase and rutile after a subsequent calcination in air, via an intermediate phase of H2Ti4O9 center dot H2O. The hierarchical structure could be retained up to 800 degrees C. When utilized as photocatalysts to degrade rhodamine B in water, the 550 degrees C-calcinated powder, with mixed phases of anatase, rutile, and srilankite, demonstrated the highest photocatalytic activity.
A facile synthesis of hierarchical flower-like TiO2 with enhanced photocatalytic activity

Jian Zhu,Shao-Hua Wang,Zhen-Feng Bian,Chen-Ling Cai,He-Xing Li

DOI: https://doi.org/10.1007/s11164-009-0096-7

IF: 3.134

2009-01-01

Research on Chemical Intermediates

Abstract:The hierarchical flower-like TiO2 has been achieved by using a simple solvothermal process without any surfactants or colloidal crystals as a template. The structures of the products were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and nitrogen adsorption-desorption analysis. The relationship between hierarchical structure and photocatalytic performance has been presented based on detailed characterizations. It was found that the hierarchical flower-like structure was a benefit for light absorption and significantly enhanced the photocatalytic activity.
A facile synthesis of hierarchical flower-like TiO 2 with enhanced photocatalytic activity

Jian Zhu,Shao-Hua Wang,Zhen-Feng Bian,Chen-Ling Cai,He-Xing Li

DOI: https://doi.org/10.1007/s11164-009-0096-7

IF: 3.134

2009-01-01

Research on Chemical Intermediates

Abstract:The hierarchical flower-like TiO 2 has been achieved by using a simple solvothermal process without any surfactants or colloidal crystals as a template. The structures of the products were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and nitrogen adsorption–desorption analysis. The relationship between hierarchical structure and photocatalytic performance has been presented based on detailed characterizations. It was found that the hierarchical flower-like structure was a benefit for light absorption and significantly enhanced the photocatalytic activity.
Facile synthesis of hierarchical Ag 3 PO 4 /TiO 2 nanofiber heterostructures with highly enhanced visible light photocatalytic properties

jinlei xie,yefeng yang,haiping he,ding cheng,minmin mao,qinxu jiang,lixin song,jie xiong

DOI: https://doi.org/10.1016/j.apsusc.2015.07.175

IF: 6.7

2015-01-01

Applied Surface Science

Abstract:Heterostructured semiconductor nanostructures have provoked great interest in the areas of energy, environment and catalysis. Herein, we report a novel hierarchical Ag3PO4/TiO2 heterostructure consisting of nearly spherical Ag3PO4 particles firmly coupled on the surface of TiO2 nanofibers (NFs). The construction of Ag3PO4/TiO2 heterostructure with tailored morphologies, compositions and optical properties was simply achieved via a facile and green synthetic strategy involving the electrospinning and solution-based processes. Owing to the synergetic effects of the components, the resulting hybrid heterostructures exhibited much improved visible light photocatalytic performance, which could degrade the RhB dye completely in 7.5 min. In addition, the coupling of Ag3PO4 particles with UV-light-sensitive TiO2 NFs enabled full utilization of solar energy and less consumption of noble metals, significantly appealing for their practical use in new energy sources and environmental issues. The developed synthetic strategy was considered to be applicable for the rational design and construction of other heterostructured catalysts. (C) 2015 Elsevier B.V. All rights reserved.
A Facile Approach for Fabrication of TiO2 Hierarchical Nanostructures and Their Photocatalytic Properties

Yinhai Tang,Mu Yang,Hongyi Gao,Jie Li,Ge Wang

DOI: https://doi.org/10.1016/j.colsurfa.2016.08.050

IF: 5.518

2016-01-01

Colloids and Surfaces A Physicochemical and Engineering Aspects

Abstract:In this paper, a novel lyophilizated evaporation-induced self-assembly (L-EISA) approach for morphology controllable TiO2 hierarchical nanostructures in pure water-based system was developed. The resulting TiO2 nanostructures were obtained by controlling the self-assembly and growth of the P123 and TiO2 sol complex. During the synthesis procedure, the aging temperature influences the self-assembled behavior of the template in the solution, the interaction between P123 and TiO2 sol particles, and the crystal growth of TiO2. At the aging temperature of 50 degrees C (P-0.5-TiO2-50), TiO2 hierarchical nanostructure composed of radical array of nanoneedle and some adhered nanocrystallines were obtained. Lyophilization was employed to retain the structure and prevent the further growth of TiO2 crystalline during the drying process. After calcination, the structures were well preserved. P-0.5-TiO2-50 possesses a relatively high surface area of similar to 210.3 m(2) g(-1) and a large average pore size of similar to 12.56 nm. With the high surface area, crystalline and specific nanostructure, P-0.5-TiO2-50 exhibits excellent photocatalytic activity on the degradation of RhB under solar-light. (C) 2016 Published by Elsevier B.V.
Construction of TiO2 Hierarchical Nanostructures from Nanocrystals and Their Photocatalytic Properties

Tiejian Zhu,Jing Li,Qingsheng Wu

DOI: https://doi.org/10.1021/am2006838

IF: 9.5

2011-01-01

ACS Applied Materials & Interfaces

Abstract:Anatase TiO(2) mesoporous structures with high specific surface areas are of special significance in various applications. In this work, hierarchical anatase TiO(2) materials with flowerlike morphologies have been prepared via a one-step template-free hydrothermal method, by using titanocene dichloride as precursor and EDA as chelating agent in aqueous solution. Particularly, the hierarchical structures are assembled from very thin TiO(2) nanosheets, which are composed of numerous highly crystallized anatase nanocrystals. In addition, the assembled materials own relatively large specific surface areas of 170 m(2)/g, and uniform mesopores of 7 nm. We further demonstrate that the hierarchical TiO(2) materials show very good photocatalytic performance when applied in photodegradation of methylene blue, which should be related to the unique features of hierarchical structures, large specific surface areas and high crystallization degree of the obtained TiO(2) materials. With these features, the hierarchical TiO(2) may find more potential applications in the fields such as dye-sensitized solar cells and lithium ion batteries.
Facile Synthesis of Ni-doped TiO2ultrathin Nanobelt Arrays with Enhanced Photocatalytic Performance

Jun-Qiang Bai,Wei Wen,Jin-Ming Wu

DOI: https://doi.org/10.1039/c6ce00015k

IF: 3.756

2016-01-01

CrystEngComm

Abstract:Because of the high specific surface area and enhanced charge migration, TiO2 with unique belt-like nanostructures finds promising applications in various fields such as photocatalysis, dye-sensitized solar cells, gas sensors, and Li-ion batteries. In the current study, a solution combustion procedure was firstly adopted to prepare a black water-proof precursor. The black precursor interacted with H2O2 at ambient temperature, achieving a precursor solution that is capable of fabricating hydrogen titanate (H2Ti2O5·H2O) nanobelt arrays on metallic Ti substrates at 60 °C. Subsequent calcination in air at 400 °C achieved arrays of ultrathin anatase TiO2 nanobelts of ca. 2–4 nm in thickness. The addition of nickel nitrate in the combustion solution achieved the Ni-doping into the resultant TiO2 nanobelts, which did not alter the nanobelt structure but significantly reduced the band gap from 3.2 eV to 2.9 eV. When compared with the commonly alkali-hydrothermal synthesized anatase TiO2 nanobelts, the present ultrathin nanobelts exhibited much improved photocatalytic activity when utilized to assist photodegradation of rhodamine B in water. The ultrathin nanobelt structure is believed to contribute to the high specific surface area, the much reduced charge migration path, and the enhanced charge transport along the longitudinal direction. The appropriate Ni-doping further enhanced the photocatalytic performance, because of the increased light harvesting efficiency and reduced charge recombination.
Hierarchical Nanosheet-Assembled Yolk–shell TiO2microspheres with Improved Photocatalytic Activity

Lu-Lu Lai,Wei Wen,Jin-Ming Wu

DOI: https://doi.org/10.1039/c6ce00578k

IF: 3.756

2016-01-01

CrystEngComm

Abstract:Nanosheet-assembled yolk-shell anatase TiO2 microspheres were synthesized utilizing the slow hydrolysis of K2TiO(C2O4)(2) in a mixed solution of H2O2 and HNO3. Under a temperature near to the ambient one, microspheres assembled with nanoparticles were firstly obtained at the early reaction stage. Prolonging the reaction duration led to the formation of urchin-like microspheres, which further developed into nanosheet-assembled yolk-shell microspheres through a dissolution-precipitation procedure. The intermediate acid washing and final calcination transformed the microspheres to phase-pure anatase TiO2. The yolk-shell anatase microspheres exhibited a photocatalytic activity twice that of the urchin-like microspheres when utilized to assist the photodegradation of both rhodamine B and phenol in water under the illumination of UV light.
Synthesis, Characterization and Photocatalytic Activity of Hierarchical Spherical TiO2 Nanostructures

Xue Bin,Liu Run,Xu Zhu-De,Sun Xin-Xing

DOI: https://doi.org/10.3321/j.issn:1001-4861.2009.01.001

2009-01-01

Chinese journal of inorganic chemistry

Abstract:Nanostructured assembly of hierarchical spherical TiO2 were synthesized via an hydrothermal route usiug TiCl3 as Ti source, polyacrylamide (PAM) and urea as additives. The morphology, crystal phases, porous structures and UV-Vis spectra of the product was characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Raman spectroscopy, nitrogen adsorption-desorption analysis and UV-Vis diffuse reflectance spectroscopy(UV-Vis DRS). The results show that the nanostructured spherical TiO2 in a diameter range of 400 similar to 600 nm are assembled by 20-40 nm nanoparticles. PAM and urea play an important role on morphology and crystal phases of the nanostructured hierarchical spherical TiO2. The photocatalytic activity of the nanostructured hierarchical spherical TiO2 was also investigated in the degradation of methyl orange under UV light.
Hierarchical TiO 2 spheres: facile fabrication and enhanced photocatalysis

Min Liu,Lingyu Piao,Wenjingb Wang

DOI: https://doi.org/10.1007/s12598-011-0259-8

IF: 6.318

2011-01-01

Rare Metals

Abstract:Hierarchical TiO 2 spheres were fabricated by means of Ti powders dissolved into HF solution following hydrothermal reaction with ammonia for the first time. The obtained TiO 2 spheres had a good anatase structure and were composed of lots of nanoparticles and nanosheets. These hierarchical TiO 2 spheres exhibited a high surface area and a large light harvesting efficiency. The photocatalytic activity of the hierarchical TiO 2 spheres was determined by degradation of methylene blue in aqueous solution, and was compared to commercial P25 titania. It is revealed that the photocatalytic activity of hierarchical TiO 2 spheres is enhanced a lot. The apparent rate constant of the hierarchical TiO 2 spheres is as 1.5 times as that of P25 titania.
3D Hierarchical Flower-Like Tio2 Nanostructure: Morphology Control and Its Photocatalytic Property

Guohui Tian,Yajie Chen,Wei Zhou,Kai Pan,Chungui Tian,Xu-ri Huang,Honggang Fu

DOI: https://doi.org/10.1039/c0ce00851f

IF: 3.756

2011-01-01

CrystEngComm

Abstract:3D hierarchical flower-like TiO2 nanostructures were synthesized via a facile solvothermal method combining a calcination process. A series of electron microscopy characterization results suggest that the growth of 3D hierarchical flower-like TiO2 nanostructures is governed by a nucleation and nuclei growth-dissolution-recrystallization growth mechanism from time-dependent morphology evolution. The influence of the experimental parameters such as reaction species, temperature, and time on the morphology growth was systematically studied. Importantly, the prepared 3D hierarchical flower-like TiO2 nanostructures showed enhanced photocatalytic activity compared with Degussa P25 for the degradation of phenol under UV light irradiation, which is attributed to its special hierarchical porous structure, good permeability, high light-harvesting capacity and more surface active sites. Electron spin resonance (ESR) detection of active oxygen species (hydroxyl radicals) and the total organic carbon (TOC) changes are also investigated to evaluate the degradation efficacy.
Ellipsoidal TiO2 Hierarchitectures with Enhanced Photovoltaic Performance.

Wenqin Peng,Masatoshi Yanagida,Han Chen,Liyuan Han

DOI: https://doi.org/10.1002/chem.201102975

2012-01-01

Chemistry

Abstract:Hierarchical TiO(2) ellipsoids 250-500 nm in size have been synthesized on a large scale by a template-free hydrothermal route. The submicrometer-sized hierarchitectures are assembled from highly crystallized anatase nanorods about 17 nm in diameter with macroporous cavities on the outer shells. Based on the time-dependent morphological evolution under hydrothermal conditions, an oriented attachment process is proposed to explain formation of the hierarchical structures. Such hierarchical TiO(2) not only adsorbs large amounts of dye molecules due to high surface area, but also shows good light scattering caused by the submicrometer size. The TiO(2) hierarchitectures were deposited on top of a transparent TiO(2) nanocrystalline main layer to construct a double-layered photoanode for dye-sensitized solar cell (DSC) application, exhibiting enhanced light harvesting and power-conversion efficiency compared to a commercial TiO(2)-based electrode.
Template-free synthesis of hierarchical TiO2 structures and their application in dye-sensitized solar cells.

Fang Shao,Jing Sun,Lian Gao,Songwang Yang,Jianqiang Luo

DOI: https://doi.org/10.1021/am200377g

IF: 9.5

2011-01-01

ACS Applied Materials & Interfaces

Abstract:We demonstrate here the synthesis of a hierarchical TiO(2) architecture without any surfactants or templates. Two kinds of structure existed simultaneously, the ordered nanoarrays at bottom provided direct conduction pathway for photo generated electrons, while the upper micro-flowers consisted of nanobelt as building units increased the light harvesting ability as the scattering part. The formation mechanism of the hierarchical architecture has been proposed by studying the morphology evolution processes upon reaction time. The performance of dye-sensitized solar cells based on the obtained hierarchical anatase TiO(2) has been also studied, giving a J(SC) = 12.44 mA cm(-2), V(OC) = 0.64 V, FF = 69.05%, and η = 5.53%, which is superior than commercial TiO(2) (P25). The UV-vis results prove that the obtained morphology is beneficial to light-scattering and thus increases the light harvesting ability. This hierarchical TiO(2) structure offers great potential for the development of high-efficiency DSSCs.
Enhanced Photocatalytic Properties of Hierarchical Microstructured TiO 2 Spheres Synthesized with Titanium Powders

bin miao,shahid hussain,wen zeng,pin cao,jing wang,sibo xu,shifang cheng

DOI: https://doi.org/10.1166/nnl.2015.1946

2015-01-01

Nanoscience and Nanotechnology Letters

Abstract:Using a simple hydrothermal method without surfactants and templates, three-dimensional (3D) crystalline anatase titanium dioxide hierarchical microstructures were synthesized. The effects of additive NaOH and H2O2 during the preparation of TiO2 were studied. The reaction time plays a significant role in the morphology transformation. The formation mechanism of microstructures was described. The photocatalysis measurements indicates that the flower-like TiO2 consisting of nanosheets exhibits the highest activity for degrading rhodamine B under UV light.
Well-organized 3D Urchin-Like Hierarchical TiO2 Microspheres with High Photocatalytic Activity

Liqin Xiang,Xiaopeng Zhao,Jianbo Yin,Baolin Fan

DOI: https://doi.org/10.1007/s10853-011-5924-7

IF: 4.5

2011-01-01

Journal of Materials Science

Abstract:This article reported a well-organized 3D urchin-like hierarchical TiO 2 which was synthesized by a simple solvothermal method without using any template or surfactant. The results of scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, and powder X-ray diffraction showed that the hierarchical morphology and size of TiO 2 could be effectively controlled by adjusting the precursor ratio of tetrabutyl titanate to TiCl 4 solution, the concentration of TiCl 4 solution, the solvothermal temperature, and the reaction time. It is believed that the formation of the urchin-like hierarchical TiO 2 followed a ‘nucleation–self-assembly–dissolution-recrystallization’ growth mechanism. In addition, the excellent photocatalytic activity of the urchin-like hierarchical TiO 2 was confirmed by photodegradation of methyl blue in water.
Facile Construction of Hierarchical Ellipsoid-shaped TiO2 Porous Nanostructure with Enhanced Photocatalytic Activity

Lili Meng,Yi Chang,Xiaoming Ma,peng liu,Tingting Liu,Yuming Guo,Lin Yang

DOI: https://doi.org/10.1039/c9ce01265f

IF: 3.756

2019-01-01

CrystEngComm

Abstract:Hierarchical ellipsoid-shaped TiO2 porous nanostructures with a high specific surface area and abundant pores are fabricated by the hierarchical assembly of TiO2 nanoparticles via a simple one-pot hydrothermal process. The as-synthesized ellipsoid-shaped TiO2 exhibits significantly enhanced photocatalytic activity for MB degradation compared to P25 under ultraviolet light and sunlight irradiation, respectively.
Facile Preparation of Hierarchical TiO2nanowire–nanoparticle/nanotube Architecture for Highly Efficient Dye-Sensitized Solar Cells

Nianqing Fu,Yan Liu,Yanchun Liu,Wei Lu,Limin Zhou,Feng Peng,Haitao Huang

DOI: https://doi.org/10.1039/c5ta05752c

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:Hierarchical TiO2architecture with a remarkably improved surface area and light scattering effect was preparedviaone-step post-treatment for dye-sensitized solar cells, achieving a high efficiency of 8.82%.
Hierarchical Z-scheme 1D/2D architecture with TiO2 nanowires decorated by MnO2 nanosheets for efficient adsorption and full spectrum photocatalytic degradation of organic pollutants

Jiejing Zhang,Yajie Hu,Hong Zheng,Pengyi Zhang

DOI: https://doi.org/10.1039/d0cy00419g

2020-01-01

Abstract:A novel hierarchical 1D/2D TiO2/MnO2 composite shows superior adsorption, full spectrum photocatalytic activity and excellent stability for organic pollutant removal.
Facile Non-Pressurized Synthesis of Nanowire-Constructed Hierarchical TiO2 Nanomaterials with Improved Dye Sensitized Solar Cell Performance

Yinghao Lv,Rui Zan,Xiaogang Wen

DOI: https://doi.org/10.1007/s10854-019-01788-x

2019-01-01

Journal of Materials Science Materials in Electronics

Abstract:Nanowire-constructed hierarchical TiO2 nanomaterials (HTN) are prepared by a facile non-hydrothermal method at atmospheric pressure. The product is characterized in detail using powder X-ray diffraction, scanning electron microscopy, transmission electron microscopy and UV–Vis spectrophotometer. The synthesized TiO2 hierarchical nanomaterials consist of nanowires of 15 nm in diameter, it possesses a high surface area of 144.65 m2/g, and demonstrate an excellent dye absorption ability (155.55 nmol/cm2), which is 2.7 times more than that of the Degussa P25. Corresponding photovoltaic performance of dye-sensitized solar cells (DSSCs) fabricated from HTN is also investigated. It exhibits an overall light-to-electricity conversion efficiency of 8.9% accompanying a short-circuit current density of 20.43 mA/cm2, an open-circuit voltage of 720 mV and fill factor of 0.61, which is much higher than that of P25 (5.5%). The significant enhancement of short-circuit current density and power conversion efficiency of HTN can be attributed to its larger dye loading amount, better charge transportation ability and excellent light scattering ability.
Sonochemical fabrication of morpho-genetic TiO 2 with hierarchical structures for photocatalyst

Shenmin Zhu,Di Zhang,Zhixin Chen,Gang Zhou,Haibo Jiang,Jinlong Li

DOI: https://doi.org/10.1007/s11051-009-9807-7

IF: 2.533

2009-01-01

Journal of Nanoparticle Research

Abstract:Titanium oxides (TiO 2 ) with hierarchical structures have been successfully replicated from biotemplate using a sonochemical method. The bio-templates, cedarwoods, were irradiated under ultrasonic waves in TiCl 4 solutions and then calcined at temperatures between 450 and 600 °C. The fine replications of the biotemplates in TiO 2 down to nanometer’s level were verified using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The photocatalytic activities were assessed by measuring the percentage degradation of methylene blue using UV–vis spectroscopy. The calcination temperature has a strong effect on the structural replication and photocatalytic activity of the replicas. It appears that the calcination temperature of 450 °C results in the best structural replication with the highest surface area of 54.8 m 2 g −1 , and thus has the best photocatalytic properties. This method provides a simple, efficient, and versatile technique for fabricating TiO 2 with hierarchical structures, and it has the potential to be applied to other systems for producing functional hierarchical materials for chemical sensor and nanodevices.

A facile synthesis of hierarchical TiO<sub>2</sub>for dye adsorption and photocatalysis

A facile synthesis of hierarchical TiO2 for dye adsorption and photocatalysis

A facile synthesis of hierarchical flower-like TiO<sub>2</sub> with enhanced photocatalytic activity

A facile synthesis of hierarchical flower-like TiO 2 with enhanced photocatalytic activity

Facile synthesis of hierarchical Ag 3 PO 4 /TiO 2 nanofiber heterostructures with highly enhanced visible light photocatalytic properties

A Facile Approach for Fabrication of TiO2 Hierarchical Nanostructures and Their Photocatalytic Properties

Construction of TiO2 Hierarchical Nanostructures from Nanocrystals and Their Photocatalytic Properties

Facile Synthesis of Ni-doped TiO2ultrathin Nanobelt Arrays with Enhanced Photocatalytic Performance

Hierarchical Nanosheet-Assembled Yolk–shell TiO2microspheres with Improved Photocatalytic Activity

Synthesis, Characterization and Photocatalytic Activity of Hierarchical Spherical TiO2 Nanostructures

Hierarchical TiO 2 spheres: facile fabrication and enhanced photocatalysis

3D Hierarchical Flower-Like Tio2 Nanostructure: Morphology Control and Its Photocatalytic Property

Ellipsoidal TiO2 Hierarchitectures with Enhanced Photovoltaic Performance.

Template-free synthesis of hierarchical TiO2 structures and their application in dye-sensitized solar cells.

Enhanced Photocatalytic Properties of Hierarchical Microstructured TiO 2 Spheres Synthesized with Titanium Powders

Well-organized 3D Urchin-Like Hierarchical TiO2 Microspheres with High Photocatalytic Activity

Facile Construction of Hierarchical Ellipsoid-shaped TiO2 Porous Nanostructure with Enhanced Photocatalytic Activity

Facile Preparation of Hierarchical TiO2nanowire–nanoparticle/nanotube Architecture for Highly Efficient Dye-Sensitized Solar Cells

Hierarchical <i>Z</i>-scheme 1D/2D architecture with TiO<sub>2</sub> nanowires decorated by MnO<sub>2</sub> nanosheets for efficient adsorption and full spectrum photocatalytic degradation of organic pollutants

Facile Non-Pressurized Synthesis of Nanowire-Constructed Hierarchical TiO2 Nanomaterials with Improved Dye Sensitized Solar Cell Performance

Sonochemical fabrication of morpho-genetic TiO 2 with hierarchical structures for photocatalyst