Abstract:Three-dimensional (3D) titania nanostructures assembled with ordered rutile nanorods have been fabricated via a surfactant-free and single-step solvothermal route. The effects of preparation parameters, including the reaction temperatures and the reactant concentrations, on the microstructure, optical properties and photocatalytic activity of the 3D TiO2 nanostructures were investigated. The results revealed that 3D TiO2 microspheres possessed a dandelion-like morphology composed of radially packed rutile nanorods. Increasing the reaction temperature leads to the formation of larger rutile crystals, but reduced the aspect ratios of nanorods. The morphology of products was dominated by irregular shapes with low titanium precursor concentration. The optical reflectance, absorption and photocatalytic properties of the samples were found to be significantly dependent on their morphology. 3D dandelion-like structures with tapered tips showed lower reflectance, more efficient light harvesting, higher surface area and consequently higher photocatalytic activity compared with those with flat tops and fragment of nanorod sectors. Moreover, TiO2 products prepared with 0.4M titanium precursor solution at 150 and 120°C showed better or equivalent photocatalytic activity compared with Degussa P25 owing to high light harvesting ability as well as less aggregation for the unique 3D dandelion-like hierarchical structure. The growth mechanism of the 3D dandelion-like nanostructures under various preparation conditions was also discussed.

Fabrication and Photocatalysis of TiO2 Flower-like Nanostructures

Controllable Hydrothermal Synthesis, Optical and Photocatalytic Properties of TiO2 Nanostructures

Hydrothermal synthesis and photocatalytic activity of combination of flowerlike TiO2 and activated carbon fibers

A facile synthesis of hierarchical TiO2 for dye adsorption and photocatalysis

Titania Nanoflowers with High Photocatalytic Activity

Low‐Temperature Transformation of Titania Thin Films from Amorphous Nanowires to Crystallized Nanoflowers for Heterogeneous Photocatalysis

Fabrication and Photocatalytic Activity of Tio2 Nanofiber Membrane

Room‐Temperature Hydrolysis of Potassium Titanyl Oxalate and Water‐Assisted Crystallization for TiO2 with High Photocatalytic Activity

Self-assembly and Photocatalysis of Mesoporous TiO 2 Nanocrystal Clusters

Controllable Fabrication of TiO(2) 1D-Nano/micro Structures: Solid, Hollow, and Tube-in-tube Fibers by Electrospinning and the Photocatalytic Performance.

Titania Nanowires Synthesized by Thermal Oxidation of Ti Plates in Vacuum

3D Flower-like TiO2 Nanostructures: Anatase-To-Rutile Phase Transformation and Photoelectrochemical Application

A facile synthesis of hierarchical TiO<sub>2</sub>for dye adsorption and photocatalysis

Facile Synthesis of Ni-doped TiO2ultrathin Nanobelt Arrays with Enhanced Photocatalytic Performance

Direct Continuous Hydrothermal Synthesis of High Surface Area Nanosized Titania

Photocatalytic activity of TiO 2 nanorods, nanowires and nanoflowers filled with TiO 2 nanoparticles

Solvothermal Growth of Three-Dimensional TiO2 Nanostructures and Their Optical and Photocatalytic Properties

Large-Scale Synthesis and Characterization of TiO2-Based Nanostructures on Ti Substrates

Photocatalytic Active Titania Nanowire Arrays on Ti Substrates

Surface roughening and top opening of single crystalline TiO2 nanowires for enhanced photocatalytic activity

Low Temperature Synthesis of Few-Layer Titanate Nanobelts on Ti Mesh and the Hot-Water Induced Transformations to Highly Photocatalytic Active Titania Nanorods