Abstract:In the fields of automotive engineering and shipbuilding, friction stir welding (FSW) is utilized for joining aluminum alloy structural components. However, the nugget zone (NZ) in FSW joints often exhibits anomalous mechanical properties, consequently diminishing the stability of the welded joints. Here, an NZ was subdivided into a high-strain nugget zone (HS-NZ) and a high-temperature nugget zone (HT-NZ). The anomalous mechanical properties of the Al-Mg-Si alloy HS-NZ were systematically investigated at welding speeds of 100 mm/min and 200 mm/min and rotational speeds of 600 rpm and 900 rpm. Compared to the HT-NZ, the average grain size of the HS-NZ reduced by a maximum of 3 μm, the density of geometrically necessary dislocations (GNDs) increased by a maximum of 0.26 ×10 14 m −2 , and the microhardness showed a maximum increase of 15 HV. However, its shear strength is lower than that of the HT-NZ, with a maximum decrease of 15 MPa, exhibiting an abnormal mechanical performance. The increase in the "soft-oriented" grains in the HS-NZ results in more localized stress concentration between "soft-oriented" and "hard-oriented" grains during the deformation, thereby providing a reasonable explanation for the observed reduction in shear strength in HS-NZ under severe loading conditions. The increase of "soft-oriented" grains is primarily attributed to the promotion of discontinuous dynamic recrystallization (DDRX) facilitated by the coupled effects of high temperature and high strain. The constructed mathematical model also illustrated the effect of the coupled temperature and strain fields on the abnormal shear strength.

Eutectic Si Accumulation in Liquid Forged A356 Alloy Wheel and Its Adverse Effect on Tensile Fracture Behavior

Mechanical Properties and Microstructure of A356-T6 Aluminum Alloy Wheel Hub Based on Casting-Spinning Process

Effect of Iron-Rich Intermetallic and Eutectic Si Accumulation on Al-Si-Mg Alloy

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Effect of the Spinning Deformation Processing on Microstructure and Mechanical Properties of A356 Wheels

Heterogeneous Microstructure and Deformation Behavior of an Automotive Grade Aluminum Alloy

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

In-situ Observation of Tensile Fracture in A357 Casting Alloys

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Microstructure and abnormal mechanical properties under the coupling effect of strain and temperature for friction-stir-welded joints of Al-Mg-Si alloy

Study on tensile properties and fractography of cast A356 aluminum alloy

Precipitates and tensile fracture mechanism in a sand cast A356 aluminum alloy

Effect of Inclusions on the Tensile Properties of Al–7% Si–0.35% Mg (A356.2) Aluminium Casting Alloy

Evolution of Microstructure and Mechanical Properties of A356 Aluminium Alloy Processed by Hot Spinning Process

Tensile properties and fractography of A356 alloy produced by EPSC-VL process

Research on Grain Coarsening Mechanism of Forged 6061 Aluminum Alloy

Microstructural Evolutions and Strengthening Mechanism according to the Aging Temperatures of a High Si Cast Aluminum Alloy

Enhanced Strength and Ductility of A356 Alloy Due to Composite Effect of Near-Rapid Solidification and Thermo-Mechanical Treatment

Homogenization on microstructure and mechanical properties of 2A50 aluminum alloy prepared by liquid forging

Microstructural Evolution and Strengthening Mechanism of an Al–Si–Mg Alloy Processed by High-Pressure Torsion with Different Heat Treatments

Effect of Heat Treatment on Microstructures and Mechanical Properties of A356 Alloy by Low Pressure Casting