Adaptive Noise-suppression Matrix Pencil for Data-compressed Impulsive Stimulated Brillouin Spectroscopy

Jiarui Li,Taoran Le,Haoyun Wei,Yan Li

DOI: https://doi.org/10.1364/fio.2022.jw4b.70

2022-01-01

Abstract:We introduce an adaptive noise-suppression Matrix Pencil method, which is immune to spectral broadening and sidebands caused by data truncation, for impulsive stimulated Brillouin signal with compressed data.

What problem does this paper attempt to address?

Sensitive impulsive stimulated Brillouin spectroscopy by an adaptive noise-suppression Matrix Pencil

Jiarui Li,Hongyuan Zhang,Minjian Lu,Haoyun Wei,Yan Li

DOI: https://doi.org/10.1364/OE.465106

IF: 3.8

2022-01-01

Optics Express

Abstract:Impulsive stimulated Brillouin spectroscopy (ISBS) plays a critical role in investigating mechanical properties thanks to its fast measurement rate. However, traditional Fourier transform-based data processing cannot decipher measured data sensitively because of its incompetence in dealing with low signal-to-noise ratio (SNR) signals caused by a short exposure time and weak signals in a multi-peak spectrum. Here, we propose an adaptive noise-suppression Matrix Pencil method for heterodyne ISBS as an alternative spectral analysis technique, speeding up the measurement regardless of the low SNR and enhancing the sensitivity of multi-component viscoelastic identification. The algorithm maintains accuracy of 0.005% for methanol sound speed even when the SNR drops 33 dB and the exposure time is reduced to 0.4 ms. Moreover, it proves to extract a weak component that accounts for 6 degrees lo from a polymer mixture, which is inaccessible for the traditional method. With its outstanding ability to sensitively decipher weak signals without spectral a priori information and regardless of low SNRs or concentrations, this method offers a fresh perspective for ISBS on fast viscoelasticity measurements and multi-component identifications. (C) 2022 Optica Publishing Group under the terms of the Optica Open Access Publishing Agreement
Performance Enhancement of Brillouin Sensing Systems Based on Compressive Sampling

Da-Peng Zhou,Wankun Ning,Dayong Shu,Wei Peng,Liang Chen,Xiaoyi Bao

DOI: https://doi.org/10.1364/osac.411822

2020-01-01

OSA Continuum

Abstract:Compressive sampling theory asserts that certain signals can be recovered from far fewer samples than traditional methods use. We propose to enhance the performance of Brillouin sensing systems by improving the signal-to-noise ratio of the Brillouin spectra with random undersampled measurements of the original noisy Brillouin spectra. The number of acquisitions can be significantly reduced, and at the same time the measurement accuracy can be improved due to the increased signal-to-noise ratio of recovered Brillouin spectra measured based on compressive sampling principle compared to those measured directly by conventional methods. Experiments show that by performing ∼30% of the acquisitions that are required by conventional systems, over 7 dB signal-to-noise ratio enhancement can be obtained. Our proposal can be applied to any practical Brillouin sensing system whose performance can be enhanced by taking the advantages of recent advancements in computational methods without costly or sophisticated hardware modifications.
A Noise-folding Suppression Method in Photonic Compressed Sampling

Na Gao,Xianfeng Tang,Yiqiao Feng,Bingxiang Hui,Xiaoguang Zhang,Lixia Xi,Wenbo Zhang

DOI: https://doi.org/10.1109/cleopr.2017.8118945

2017-01-01

Abstract:We utilize a preprocessing method of Whitening Filter in photonic compressed sampling, which can resist the noise-folding problem. The numerical analysis shows that this method can get 20% higher successful recovery ratio of spectral support set compared with traditional method when signal to noise ratio(SNR) is lower than -3dB.
Sub-Nyquist Sampled Analog-to-Digital Conversion Based on Photonic Time Stretch and Compressive Sensing with Optical Random Mixing

Ying Chen,Hao Chi,Tao Jin,Shilie Zheng,Xiaofeng Jin,Xianmin Zhang

DOI: https://doi.org/10.1109/jlt.2013.2282088

IF: 4.7

2013-01-01

Journal of Lightwave Technology

Abstract:An approach to realizing wideband analog-to-digital conversion based on the techniques of photonic time stretch (PTS) and compressive sensing (CS) is proposed. In the system, a multitone signal within a wide bandwidth (spectrally sparse) signal is slowed down in the time domain by a photonic time stretcher. The stretched signal is then down-sampled and reconstructed by a random-demodulator-based CS scheme, in which random mixing is realized in an optical domain. Thanks to the techniques of PTS and CS, wideband spectrally sparse signals can be acquired with a sampling rate far below the Nyquist rate of the original signal. The optical random mixing applied in the system has the advantages of lower distortions and larger bandwidth compared to its electrical counterpart. In order to construct a Gaussian measurement matrix with zero mean, balanced detection is applied after the optical mixer. In addition, in order to eliminate the dc component and the even-order harmonics of the stretched signal, we propose to use balanced PTS technique in the system. We demonstrate that a system with a time stretch factor 20 and a compression factor 4 can effectively acquire a spectrally sparse wideband signal, which means a sampling rate as low as 1/80 of the Nyquist rate.
Compressive Whiskbroom Sensing and Data Reconstruction for Hyperspectral Imaging

Yingbiao JIA,Yan FENG

2017-01-01

Abstract:Owing to the requirements of high spectral resolution, conventional hyperspectral remote-sensing imaging systems are susceptible to bottleneck problems related to high rate sampling and mass data storage. Compressive sampling possesses the potential to solve many problems associated with hyperspectral remote sensing. An optical imaging system for compressive whiskbroom sensing in hyperspectral remote-sensing imaging is proposed in this paper. The proposed system comprises spatial grating, a cylindrical lens, a two-dimensional coded aperture, and a linear sensor array. The system, which enables multiple simultaneous compressive measurements, is designed for spectrum sensing operations. An iterative prediction reconstruction algorithm is designed based on the spatial correlation of hyperspectral images. Experimental results show that the reconstruction signal-to-noise ratio of the proposed algorithm is improved by more than 10dB when the sampling rate exceeds 0.2. The sampling simplicity of the system makes it suitable for hyperspectral compressive imaging in space-borne and airborne remote-sensing platforms.
Robust Compressive Two-Dimensional Near-Field Millimeter-Wave Image Reconstruction in Impulsive Noise

Jue Lyu,Dongjie Bi,Xifeng Li,Yongle Xie

DOI: https://doi.org/10.1109/lsp.2019.2892515

2019-01-01

IEEE Signal Processing Letters

Abstract:In this letter, a novel robust two-dimensional near-field millimeter-wave (MMW) image reconstruction algorithm is developed based on compressed sensing (CS) in the presence of impulsive measurement noise. To enable the sparse MMW image recovery, the CS algorithm usually employs the popular l(2) -norm as the data fidelity term and a combination of multiple sparsity-induced functions as the penalty term. The l(2) -norm is non-robust against impulsive noise since the Gaussian noise distribution assumption is not valid, and the presence of impulsive noise will severely degrade the robustness of the compressive MMW image recovery. To gain more robustness performance, a complex correntropy based data-fitting term, namely complex correntropic loss (CC-loss), is used to replace the l(2) -norm for the near-field MMW measurement contaminated by impulsive noise. In order to solve the corresponding minimization problem, an additive half quadratic method is used to transform the CC-loss term to its convex form, and then a parallel primal-dual process is used to guarantee the convergence of the proposed algorithm. In total, 150-GHz MMW experimental results show that the proposed algorithm can achieve accurate image reconstruction from compressive measurements under different impulsive noise levels.
High-speed impulsive stimulated Brillouin microscopy

Jiarui Li,Taoran Le,Hongyuan Zhang,Haoyun Wei,Yan Li

2023-12-06

Abstract:Brillouin microscopy, which maps elastic modulus from the frequency shift of scattered light, has evolved to a faster speed for the investigation of rapid biomechanical changes. Impulsive stimulated Brillouin scattering (ISBS) spectroscopy has the potential to speed up measurement through the resonant amplification interaction from pulsed excitation and time-domain continuous detection. However, significant progress has not been achieved due to the limitation in signal-to-noise ratio (SNR) and the corresponding need for excessive averaging to maintain high spectral precision. Moreover, the limited spatial resolution also hinders its application in mechanical imaging. Here, by scrutinizing the SNR model, we design a high-speed ISBS microscope through multi-parameter optimization including phase, reference power, and acquisition time. Leveraging this, with the further assistance of the Matrix Pencil method for data processing, three-dimensional mechanical images are mapped under multiple contrast mechanisms for a millimeter-scale polydimethylsiloxane pattern immersed in methanol, enabling the identification of these two transparent materials without any contact or labeling. Our experimental results demonstrate the capability to maintain high spectral precision and resolution at a sub-millisecond integration time for one pixel. With a two-order improvement in the speed and a tenfold improvement in the spatial resolution over the state-of-the-art systems, this method makes it possible for ISBS microscopes to sensitively investigate rapid mechanical changes in time and space.

Optics
A Noise Suppression Method for Optical Spectrum Measurement Utilizing SBS-based Filter

Deng Pan,Changjian Ke,Songnian Fu,Deming Liu,Alan E. Willner

DOI: https://doi.org/10.1364/ofc.2015.w3i.1

2015-01-01

Abstract:A comprehensive noise suppression method for SBS-based filter is proposed and experimentally demonstrated. Accompanied with linearization, the processed spectral dynamic range of an OOK signal can be improved from ~10 dB to ~60 dB.
Investigation on the Noise Suppression of Brillouin Amplification for Weak Stokes Signals

Weiming He,Hongbo Liu,Wuliji Hasi,Zhiwei Lu

DOI: https://doi.org/10.1109/icoom.2012.6316259

2012-01-01

Abstract:For weak Stokes Brillouin amplification, the speckle noise of the amplified spontaneous Brillouin scattering (ABS) of pump laser limits the signal to noise ratio (SNR). This paper introduces the design of a double signal Brillouin amplification scheme, it can improve the SNR for weak signal Brillouin amplification. The experimental results show that the non-collinear strong Stokes Brillouin amplification can reduce ABS noise by more than two orders of magnitude, the collinear weak Stokes signal optical magnification decreases only one order of magnitude, nJ collinear weak signal can still get 105 magnification. Double signal Brillouin amplification scheme can substantially in the amplified signal, at the same time, can effectively improve the optical SNR, and improve the reliability of signal measurement.
Quarter acoustic period pulse compression using stimulated Brillouin scattering in PF-5060

Zhaohong Liu,Rong Fan,Duo Jin,Tiantian Luo,Sensen Li,Ning Li,Shaowen Li,Yulei Wang,Zhiwei Lu

DOI: https://doi.org/10.1364/OE.453014

IF: 3.8

2022-01-01

Optics Express

Abstract:The pulse duration of the near quarter-acoustic period (tau(a)) is demonstrated in transient stimulated Brillouin scattering (SBS) pulse compression by the suppressing Stokes trailing-edge broadening at high intensities. A theoretical analysis reveals that the difficulty in attaining the transient compression limit is caused by the broadening of the Stokes trailing edge owing to insufficient pump depletion, and this undesirable phenomenon can be significantly suppressed by a high SBS gain coefficient. An average pulse duration of similar to 1.05 tau(a) was experimentally achieved in transient compression with a high-energy efficiency of over 30%. Benefiting from energy back conversion, compression below the transient SBS limit (< tau(a)) also occurred when the pump peak power was increased to 150 MW. (C) 2022 Optica Publishing Group under the terms of the Optica Open Access Publishing Agreement
Truly Sub-Nyquist Method Based Matrix Pencil and CRT with Super Resolution

Huiguang Zhang,Baoguo Liu

2024-10-23

Abstract:The emergence of ultra-wideband (UWB) and high-throughput signals has necessitated advancements in data sampling technologies1. Sub-Nyquist sampling methods, such as the modulated wideband converter (MWC) and compressed auto-correlation spectrum sensing (CCS), address the limitations of traditional analog-to-digital converters (ADCs) by capturing signals below the Nyquist rate. However, these methods face challenges like spectral leakage and complex hardware requirements. This paper proposes a novel super-resolution generalized eigenvalue method that integrates the matrix pencil method with the Chinese Remainder Theorem (CRT) to enhance signal processing capabilities within a true sub-Nyquist framework3. This approach aims to improve frequency resolution and accuracy in high-frequency signal extraction, with potential applications in telecommunications, radar, and medical imaging.

Information Theory
Streak Artifact Suppressed Back Projection for Sparse-View Photoacoustic Computed Tomography.

Tong Wang,Chenyang Chen,Kang Shen,Wen Liu,Chao Tian

DOI: https://doi.org/10.1364/ao.487957

IF: 1.9

2023-01-01

Applied Optics

Abstract:The development of fast and accurate image reconstruction algorithms under constrained data acquisition conditions is important for photoacoustic computed tomography (PACT). Sparse-view measurements have been used to accelerate data acquisition and reduce system complexity; however, reconstructed images suffer from sparsity-induced streak artifacts. In this paper, a modified back-projection (BP) method termed anti-streak BP is proposed to suppress streak artifacts in sparse-view PACT reconstruction. During the reconstruction process, the anti-streak BP finds the back-projection terms contaminated by high-intensity sources with an outlier detection method. Then, the weights of the contaminated back-projection terms are adaptively adjusted to eliminate the effects of high-intensity sources. The proposed anti-streak BP method is compared with the conventional BP method on both simulation and in vivo data. The anti-streak BP method shows substantially fewer artifacts in the reconstructed images, and the streak index is 54% and 20% lower than that of the conventional BP method on simulation and in vivo data, when the transducer number N=128. The anti-streak BP method is a powerful improvement of the BP method with the ability of artifact suppression.
A Robust Iteratively Reweighted $\ell _2$ Approach for Spectral Compressed Sensing in Impulsive Noise

Zhen-Qing He,Hongbin Li,Zhi-Ping Shi,Jun Fang,Lei Huang

DOI: https://doi.org/10.1109/lsp.2017.2698721

2017-01-01

IEEE Signal Processing Letters

Abstract:This letter concentrates on the problem of spectral compressed sensing in impulsive noise, which aims to recover a spectrally sparse signal from its contaminated and undersampled measurements. We propose a robust formulation for joint sparse signal and frequency recovery, which includes the generalized l(p)-norm (0 < p < 2) data-fidelity fitting term added to a log-sum sparsity-promoting regularizer. To handle this intractable issue, we develop an iteratively reweighted l(2) approach via majorizing the original objective function by a quadratic surrogate function. Simulation results illustrate that the proposed approach attains a significant performance improvement over the existing methods under impulsive noise.
Data-Driven Sampling Matrix Boolean Optimization for Energy-Efficient Biomedical Signal Acquisition by Compressive Sensing.

Yuhao Wang,Xin Li,Kai Xu,Fengbo Ren,Hao Yu

DOI: https://doi.org/10.1109/tbcas.2016.2597310

2017-01-01

IEEE Transactions on Biomedical Circuits and Systems

Abstract:Compressive sensing is widely used in biomedical applications, and the sampling matrix plays a critical role on both quality and power consumption of signal acquisition. It projects a high-dimensional vector of data into a low-dimensional subspace by matrix-vector multiplication. An optimal sampling matrix can ensure accurate data reconstruction and/or high compression ratio. Most existing optimization methods can only produce real-valued embedding matrices that result in large energy consumption during data acquisition. In this paper, we propose an efficient method that finds an optimal Boolean sampling matrix in order to reduce the energy consumption. Compared to random Boolean embedding, our data-driven Boolean sampling matrix can improve the image recovery quality by 9 dB. Moreover, in terms of sampling hardware complexity, it reduces the energy consumption by 4.6× and the silicon area by 1.9× over the data-driven real-valued embedding.
Accelerated Fast BOTDA Assisted by Compressed Sensing and Image Denoising

Hua Zheng,Yaxi Yan,Zhiyong Zhao,Tao Zhu,Jingdong Zhang,Nan Guo,Chao Lu

DOI: https://doi.org/10.1109/jsen.2021.3117287

IF: 4.3

2021-11-15

IEEE Sensors Journal

Abstract:We propose and experimentally demonstrate a scheme for accelerated fast BOTDA. The effect of signal-to-noise ratio (SNR) on recovery performance of compressed sensing is simulated and analyzed, it is found that a reduction in SNR requires much larger frequency data to recover the original Brillouin gain spectrum (BGS). To enable a high recovery probability, Block-Matching and 3D filtering (BM3D) algorithm is employed to enhance the SNR of Brillouin time trace and reduce the number of averages. Combining with a principal component analysis (PCA) based compressed sensing technique, the Brillouin gain spectrum (BGS) can be successfully reconstructed from only 37.5% frequency data. In the experiment, 75 randomly selected frequency data is acquired to reconstruct the BGS. Distributed strain sensing is achieved over 15 km single-mode fiber with 3 m spatial resolution and 0.52 MHz Brillouin frequency shift (BFS) uncertainty. Due to the accelerated process, the measurement time with 40 averages is less than 0.5 s.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
Streak artifact suppression in photoacoustic computed tomography using adaptive back projection.

Chuangjian Cai,Xuanhao Wang,Ke Si,Jun Qian,Jianwen Luo,Cheng Ma

DOI: https://doi.org/10.1364/BOE.10.004803

IF: 3.4

2019-01-01

Biomedical Optics Express

Abstract:For photoacoustic computed tomography (PACT), an insufficient number of ultrasound detectors can cause serious streak-type artifacts. These artifacts get overlaid on top of image features, and thus locally jeopardize image quality and resolution. Here, a reconstruction algorithm, termed Contamination Tracing Back-Projection (CTBP), is proposed for the mitigation of streak-type artifacts. During reconstruction, CTBP adaptively adjusts the back-projection weight, whose value is determined by the likelihood of contamination, to minimize the negative influences of strong absorbers. An iterative solution of the eikonal equation is implemented to accurately trace the time of flight of different pixels. Numerical, phantom and in vivo experiments demonstrate that CTBP can dramatically suppress streak artifacts in PACT and improve image quality. (C) 2019 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
Brillouin Filtering With Enhanced Noise Performance And Linearity Using Anti-Stokes Interactions

Amol Choudhary,Yang Liu,David Marpaung,Benjamin J. Eggleton

DOI: https://doi.org/10.1364/cleo_si.2018.stu4f.2

2018-01-01

Abstract:The anti-Stokes component of a stimulated Brillouin scattering interaction enabled low power and high-resolution bandpass filtering, with improvements in linearity and signal-to-noise ratio of upto 3dB and 8dB, respectively when compared to using the Stokes component.
Numerical Simulation of Noise in Pulsed Brillouin Scattering

Oscar A. Nieves,Matthew D. Arnold,Michael J. Steel,Mikolaj K. Schmidt,Christopher G. Poulton

DOI: https://doi.org/10.1364/JOSAB.428809

2021-06-23

Abstract:We present a numerical method for modelling noise in Stimulated Brillouin Scattering (SBS). The model applies to dynamic cases such as optical pulses, and accounts for both thermal noise and phase noise from the input lasers. Using this model, we compute the statistical properties of the optical and acoustic power in the pulsed spontaneous and stimulated Brillouin cases, and investigate the effects of gain and pulse width on noise levels. We find that thermal noise plays an important role in the statistical properties of the fields, and that laser phase noise impacts the SBS interaction when the laser coherence time is close to the time-scale of the optical pulses. This algorithm is applicable to arbitrary waveguide geometries and material properties, and thus presents a versatile way of performing noise-based SBS numerical simulations, which are important in signal processing, sensing, microwave photonics and opto-acoustic memory storage.

Optics
Fluctuation Initiation of Stokes Signal and Its Effect on Stimulated Brillouin Scattering Pulse Compression

Hang Yuan,Yulei Wang,Zhiwei Lu,Yirui Wang,Zhaohong Liu,Zhenxu Bai,Can Cui,Rui Liu,Hengkang Zhang,Wuliji Hasi

DOI: https://doi.org/10.1364/oe.25.014378

IF: 3.8

2017-01-01

Optics Express

Abstract:In this paper, a theoretical model is developed to demonstrate that fluctuations in the Stokes signal and occurrence position contribute to the final compression ratio in stimulated Brillouin scattering (SBS). This theoretical analysis can be applied to the investigation of the temporal characteristics of SBS pulse compression. This model agrees well with the experimental results in a two-stage SBS compressor.
Enhancement of Time-Delay Measurement Accuracy of an Insufficient Stimulated Brillouin Scattering Based Pulse Compression System Via Lock-in Detection.

Yonglan Yang,Xing Li,Jianping Chen,Weiwen Zou

DOI: https://doi.org/10.1364/oe.411111

IF: 3.8

2020-01-01

Optics Express

Abstract:We demonstrate a novel scheme to increase the accuracy of time-delay measurement of an insufficient stimulated Brillouin scattering (ISBS) based pulse compression system. It is realized by relating the time delay with the pulse compression gain, which is accumulated by a lock-in amplifier (LIA). We theoretically demonstrate that the time delay is proportional to the accumulated gain via the LIA. In the experiment, the pulse compression gain is accumulated through lock-in detection. It narrows down the detection bandwidth and reduces the influence from the broadband noise. The time-delay measurement is completed in a real-time manner and thus provides a possible solution to realizing a high-speed process in the future. The accuracy of measurement of a linear frequency modulated (LFM) signal with a bandwidth of 1 GHz is 1 ns.

Adaptive Noise-suppression Matrix Pencil for Data-compressed Impulsive Stimulated Brillouin Spectroscopy

Sensitive impulsive stimulated Brillouin spectroscopy by an adaptive noise-suppression Matrix Pencil

Performance Enhancement of Brillouin Sensing Systems Based on Compressive Sampling

A Noise-folding Suppression Method in Photonic Compressed Sampling

Sub-Nyquist Sampled Analog-to-Digital Conversion Based on Photonic Time Stretch and Compressive Sensing with Optical Random Mixing

Compressive Whiskbroom Sensing and Data Reconstruction for Hyperspectral Imaging

Robust Compressive Two-Dimensional Near-Field Millimeter-Wave Image Reconstruction in Impulsive Noise

High-speed impulsive stimulated Brillouin microscopy

A Noise Suppression Method for Optical Spectrum Measurement Utilizing SBS-based Filter

Investigation on the Noise Suppression of Brillouin Amplification for Weak Stokes Signals

Quarter acoustic period pulse compression using stimulated Brillouin scattering in PF-5060

Truly Sub-Nyquist Method Based Matrix Pencil and CRT with Super Resolution

Streak Artifact Suppressed Back Projection for Sparse-View Photoacoustic Computed Tomography.

A Robust Iteratively Reweighted $\ell _2$ Approach for Spectral Compressed Sensing in Impulsive Noise

Data-Driven Sampling Matrix Boolean Optimization for Energy-Efficient Biomedical Signal Acquisition by Compressive Sensing.

Accelerated Fast BOTDA Assisted by Compressed Sensing and Image Denoising

Streak artifact suppression in photoacoustic computed tomography using adaptive back projection.

Brillouin Filtering With Enhanced Noise Performance And Linearity Using Anti-Stokes Interactions

Numerical Simulation of Noise in Pulsed Brillouin Scattering

Fluctuation Initiation of Stokes Signal and Its Effect on Stimulated Brillouin Scattering Pulse Compression

Enhancement of Time-Delay Measurement Accuracy of an Insufficient Stimulated Brillouin Scattering Based Pulse Compression System Via Lock-in Detection.