Abstract:The International Maritime Organization (IMO) has implemented new sulfur content regulations for marine fuels in response to growing environmental concerns, including global warming. These regulations severely and costly restrict refinery operations. Oxidative desulfurization (ODS) is an attractive desulfurization method that has advantages such as mild operating conditions and a hydrogen-free process over traditional processes such as hydrodesulfurization (HDS). One can employ oxidative desulfurization in addition to or instead of hydrodesulfurization. Organic sulfur molecules undergo oxidative desulfurization, which results in the formation of polar sulfones. The refined fuel oil is then separated from the oxidized sulfones using methods such liquid-liquid extraction, distillation, and absorption. This work examines and simulates the process of separating sulfur-containing oxidized chemicals from fuel oil utilizing oxidative desulfurization technology. Acetic acid served as the catalyst and hydrogen peroxide as the chosen oxidant. This effort involved simulating the oxidative desulfurization of fuel oil and then using absorption methods to separate the oxidized sulfones. Subsequent procedures including absorption and distillation were used to separate and recover the resultant effluent, solvent, and oxidant from the remaining components. According to the simulation results, the procedure was run at 80 °C and a modest pressure of less than 5 bar. Sulfur content in the original hydrocarbon fuel was 3.5% by weight; at the output, it was less than 0.5% by weight. The findings of the sensitivity analysis of a few key factors demonstrated that the conversion percentage increased from 84 to 98% when the reactor's diameter was changed from 0.5 to 1.2 m and its length was extended to the desired amount. The reaction conversion percentage has increased significantly when the mass flow rate of hydrogen peroxide is increased from 0.5 to 1.5 kg/h, the pressure is increased from 1.5 to 5 bar, and the temperature is raised to 30 °C. According to the process optimization data, the ideal state had an exergy efficiency of 55.57%, a solvent waste rate of 1.75%, and a sulfur content of 0.22% in the fuel.

Complex physicochemical process of low sulfur heavy fuel oil under high temperatures and pressures

Co-hydrotreating of Algae and Used Engine Oil for the Direct Production of Gasoline and Diesel Fuels or Blending Components

Experimental and Numerical Investigation of Low Sulfur Heavy Fuel Oil Spray Characteristics under High Temperature and Pressure Conditions

Spray Evolution and Thermal Pyrolysis of Low Sulfur Heavy Fuel Oils under High Temperatures

Research on Desulfurization Technology of Low Sulfur Marine Fuel Oil

Characteristics of Particulate Matter Emissions for Low-Sulfur Heavy Oil Used in Low-Speed Two-Stroke Diesel Engines of Ocean-Going Ships

Study on characteristics of marine heavy fuel oil and low carbon alcohol blended fuels at different temperatures

Pm and Parent, Nitrated- and Oxygenated-Pahs Emissions of Emulsified Heavy Fuel Oil in Marine Low-Speed Main Engine

Simulation and optimization of heavy fuel oil (HFO) refining platform to low sulfur marine fuel (LS-FO) by oxidative desulfurization

An Investigation on Pyrolysis Characteristics of Low-Sulfur Heavy Fuel Oil Spray under Diesel Engine-Like Conditions

Research on the Influence of Hydrogen and Oxygen Fuel Obtained from Water Electrolysis on Combustion Stability of Shale Gas Engines

Experimental investigation on NOx and green house gas emissions from a marine auxiliary diesel engine using ultralow sulfur light fuel

Swirling Flame Combustion of Heavy Fuel Oil: Effect of Fuel Sulfur Content

Particulate Matter (PM) and Parent, Nitrated and Oxygenated Polycyclic Aromatic Hydrocarbon (PAH) Emissions of Emulsified Heavy Fuel Oil in Marine Low-Speed Main Engine

Effect of Swirl Flow on Spray and Combustion Characteristics with Heavy Fuel Oil under Two-Stroke Marine Engine Relevant Conditions

Development of Surrogate Fuels for Heavy Fuel Oil in Marine Engine

Swirling Flame Combustion of Heavy Fuel Oil Blended with Diesel: Effect of Asphaltene Concentration

Finer Particle Size Distribution and Potential Higher Toxicity of Elemental Carbon and Polycyclic Aromatic Hydrocarbons Emitted by Ships after Fuel Oil Quality Improvement

Enhanced Emission of Intermediate/semi-Volatile Organic Matters in Both Gas and Particle Phases from Ship Exhausts with Low-Sulfur Fuels

Effects on of Blended Biodiesel and Heavy Oil on Engine Combustion and Black Carbon Emissions of a Low-Speed Two-Stroke Engine

Characteristics of Particulate Matter Emissions from a Low-Speed Marine Diesel Engine at Various Loads