Abstract:Thin features are integral components of most lightweight cellular lattice structures; however, limited studies are carried out to understand their property/quality aspects. This experimental study investigates the influence of powder feedstock size, feature geometry, and process parameters on the property/quality of thin lightweight features fabricated using a laser powder bed fusion additive manufacturing (L-PBF-AM) system. Three different Ti6Al4V powder feedstocks (fine, medium, and coarse) were utilized, and the dimensions of the features were varied in the range of 0.1 to 0.5 mm. The experimental data were analyzed to gain insights into the powder feedstock-geometry-process-property/quality (PGPP/PGPQ) characteristics, which had not been previously explored but are crucial for designing lightweight structures using L-PBF-AM. The results indicated that both powder feedstock size and feature dimension significantly influenced the properties and quality of the fabricated thin features. Additionally, feature type, volumetric energy density, and their interactions exhibited varying effects on geometrical accuracy, porosity, grain size, and flexural properties. Struts showed lower success rates, grain sizes, and dimensional errors but higher mechanical properties compared to walls. However, both features exhibited similar porosity characteristics. Regarding powder feedstock size, smaller powder sizes were found to be advantageous for fabricating lower-dimensional features and improving their mechanical properties. The feature geometry type also significantly influences the final material properties. A notable observation was that the 0.1 mm wall features exhibited the lowest mechanical properties, particularly in terms of yield strength, while the 0.5 mm strut features exhibited lower mechanical properties among the struts. The findings of the study underscored the importance of understanding the compound relationships between powder feedstock, feature geometry, process parameters, and the resulting properties/quality for lightweight features in L-PBF-AM. Further research is necessary to establish the knowledge and understanding of L-PBF-AM thin features and elucidate the PGPP/PGPQ characteristics in greater detail.

Evolutionary Behavior of Haynes 230 Powder During Laser Powder Bed Fusion Cycle and Its Effect on the Mechanical Performance of Manufactured Parts

Simultaneous regulation of strength and ductility of laser powder bed fusion manufactured Haynes 230 alloy

Reusability of Ti–6Al–4 V Powder in Laser Powder Bed Fusion: Influence on Powder Morphology, Oxygen Uptake, and Mechanical Properties

Effect of Surface Modification on the High Temperature Low Cycle Fatigue Performance of LPBF 316L Austenitic Steel

Powder recycling effects on porosity development and mechanical properties of Hastelloy X alloy during laser powder bed fusion process

Effect of Powder Variability on Laser Powder Bed Fusion Processing and Properties of 316L

Effect of particle surface roughness on the flowability and spreadability of Haynes 230 powder during laser powder bed fusion process

Powder coarsening mechanisms of Ti-6Al-4 V with multiple build cycles in laser powder bed fusion

Inheritance of Microstructure and Mechanical Properties in Laser Powder Bed Fusion Additive Manufacturing: A Feedstock Perspective

Influence of the Properties of Ti6Al4V Powder Materials on the Build Quality of Laser Powder Bed Fusion–manufactured Components

Study of the Printability, Microstructures, and Mechanical Performances of Laser Powder Bed Fusion Built Haynes 230

Influence of the physicochemical properties of reusable powders on the mechanical properties of Ti6Al4V manufactured via laser powder bed fusion additive manufacturing

Effects of Ti6al4v Powder Oxidation on Process Dynamics in Laser Powder Bed Fusion Additive Manufacturing

Influence of particle morphology and size distribution on the powder flowability and laser powder bed fusion manufacturability of Ti-6Al-4V alloy

Promoting Densification and Strengthening Effect of Ultrasonic Impact Treatment on Haynes 230 Alloy Manufactured by Laser Powder Bed Fusion

Laser Powder Bed Fusion of Haynes 230 Superalloy: Microstructure, Mechanical Properties and Hot Cracking Inhibition

Laser powder bed fusion additively manufactured thin lightweight Ti6Al4V features: an experimental investigation on the influence of powder feedstock, geometry, and process parameters on property/quality

Effects of Powder Surface Conditions on the Rheological Behavior of Ti–6Al–4 V Alloy Powders for Additive Manufacturing

Influences of Powder Packing Density in Laser Powder Bed Fusion Metal Additive Manufacturing

Powder Reuse in Laser-Based Powder Bed Fusion of Ti6Al4V—Changes in Mechanical Properties during a Powder Top-Up Regime

Part geometry and conduction-based laser power control for powder bed fusion additive manufacturing