Abstract:Using flue gas can provide a low-cost technology for carbon utilization and storage (CCUS). Nitrogen and Carbon Dioxide (flue gas) foam can control gas mobility and decrease water cut; however, the instability of flue gas foam limits its utilization. The addition of fly ash and clay particles can significantly improve foam stability and optimize the foam system. While the mechanism of fly ash stabilizing foam is well understood, the mechanism of clay as a foam stabilizer remains unclear.In this paper, the foam quality of two anionic surfactants, SDS and SDBS, and one cationic surfactant CTAB were compared to each other. The three surfactants were screened based on their different charge and foaming performance since they have almost the same interfacial tension IFT values. The impact of different mixtures of carbon dioxide and nitrogen on the foam stability and foam volume of SDS, SDBS, and CTAB surfactants was analyzed. Foam stability is evaluated by measurement of half-life time, and foaming ability is obtained by recording the foam volume right after the forming of foam. The influence of fly ash and clay particles on the stability of nitrogen and SDS foam was evaluated. The process of liquid discharge from flue gas foam and its structure was compared in different gas proportions and times using Foamscan.The experimental results showed that the stability of CTAB, SDBS, and SDS foam is the best in a pure nitrogen environment because the solubility of N2 in water is lower than that of CO2, which decreases gas diffusion between bubble films and leads to high foam stability. Among the three surfactants, SDS has the best foam quality, which is due to Zeta potential value, which affects the molecular arrangement, and thus the liquid discharge rate. When fly ash and clay particles were added to the SDS solution, the stability and foaming ability of the foam was greatly improved because of the migration of fly ash particles to the gas/liquid interface and formed a shield that protected the bubbles and minimized liquid drainage. With the addition of nano fly ash and clay particles, the half-life time of N2 foam discharge could be improved by about 1171.429%. Similarly, foam volume was relatively increased after the addition of nano fly ash and clay particles to the solution of SDS surfactant.This work provides an understanding of the mechanism of the synergistic effect of fly ash particles on the adsorbing of surfactant in the interlayer between solution and gas. Furthermore, the generated foam system with thermal stability and salt resistance could be utilized in EOR and hydraulic fracturing under formation conditions.

Synergy of Fly Ash and Surfactant on Stablizing Flue Gas Foam for Ccus

Investigation of the Effect of Nanoparticle-Stabilized Foam on EOR: Nitrogen Foam and Methane Foam

Synergistic Stabilization Mechanism of SiO2 Nanoparticles and Anionic Surfactants During Foam Fracturing

Synergistic Stabilization Mechanism of SiO 2 Nanoparticles and Anionic Surfactants during Foam Fracturing

On the mechanism of enhanced foam stability by combining carboxylated cellulose nanofiber with hydrocarbon and fluorocarbon surfactants

Aggregation behavior and foam properties of the mixture of hydrocarbon and fluorocarbon surfactants with addition of nanoparticles

Colloidal Particle-Stabilized Foam To Control the Coal Spontaneous Combustion: Stability Mechanism Analysis and Extinguishing Properties

Surfactant and a mixture of surfactant and nanoparticles to stabilize CO2/brine foam, control gas mobility, and enhance oil recovery

Sol–gel-stabilized CO2 foam for enhanced in-situ carbonation in foamed fly ash backfill materials

CO2 in water foam stabilized with CO2-dissolved surfactant at high pressure and high temperature

Investigations on the Influencing Mechanisms of SiO 2 Nanoparticles on Foam Stability

Experimental study of foam stability and interfacial behaviour of cellulose nanocrystals-enhanced C22-tailed zwitterionic betaine surfactant

Aqueous CO 2 Foam Armored by Particulate Matter from Flue Gas for Mobility Control in Porous Media

Bulk Foam Stability and Rheological Behavior of Aqueous Foams Prepared by Clay Particles and Alpha Olefin Sulfonate

A Novel Supercritical CO2 Foam System Stabilized With a Mixture of Zwitterionic Surfactant and Silica Nanoparticles for Enhanced Oil Recovery

Stability mechanism of SiO2/SDS dispersion for foam flooding in hydrocarbon reservoirs: experimental research and molecular simulation

Utilization of nanoparticle-stabilized foam for gas well deliquification

Insight on Methane Foam Stability and Texture via Adsorption of Surfactants on Oppositely Charged Nanoparticles.

Surfactant foam injection for remediation of diesel-contaminated soil: A comprehensive study on the role of co-surfactant in foaming formulation enhancement

Liquid Foam Stabilized by a CO2-Responsive Surfactant and Similarly Charged Cellulose Nanofibers for Reversibly Plugging in Porous Media

Thermal Stability of Gel Foams Stabilized by Xanthan Gum, Silica Nanoparticles and Surfactants