Abstract:Ten percent Cr steels are considered to be prospective materials for the production of pipes, tubes, and blades in coal-fired power plants, which are able to operate within ultra-supercritical steam parameters. The microstructural evolution of a Re-containing 10% Cr-3Co-3W steel with low N and high B content during creep was investigated at different strains at 923 K and under an applied stress of 120 MPa using TEM and EBSD analyses. The studied steel had been previously normalized at 1323 K and tempered at 1043 K for 3 h. In the initial state, the tempered martensite lath structure with high dislocation density was stabilized by M23C6 carbides, NbX carbonitrides, and M6C carbides. At the end of the primary creep stage, the main microstructural change was found to be the precipitation of the fine Laves phase particles along the boundaries of the prior austenite grains, packets, blocks, and martensitic laths. The remarkable microstructural degradation processes, such as the significant growth of martensitic laths, the reduction in dislocation density within the lath interiors, and the growth of the grain boundary Laves phase particles, occurred during the steady-state and tertiary creep stages. Moreover, during the steady-state creep stage, the precipitation of the V-rich phase was revealed. Softening was in accordance with the dramatic reduction in hardness during the transition from the primary creep stage to the steady-state creep stage. The reasons for the softening were considered to be due to the change in the strengthening mechanisms and the interactions of the grain boundary M23C6 carbides and Laves phase with the low-angle boundaries of the martensitic laths and free dislocations.

Nanoindentation Behavior and Creep-Induced Cracking of Long-Term Crept Austenitic Steel at 650 °C

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Microstructure of 10% Cr Martensitic Heat-Resistant Steel Welded Joints and Type IV Cracking Behavior During Creep Rupture at 650°C

Characterization of the Cyclic Softening and Remaining Creep Behaviour of P92 Steel Weldment

Nano-Indentation Creep Behavior of the Vacuum Electron Beam Weldment of 12cr10co3w2monivnbnb Heat Resistant Steel

The Evolution of Precipitates of 22cr–25ni–mo–nb–n Heat-Resistant Austenitic Steel in Long-Term Creep

Correlation of Creep Fracture Lifetime with Microstructure Evolution and Cavity Behaviors in G115 Martensitic Heat-Resistant Steel

Effects of Pre-Creep on Dislocation and Tensile Property of Cr-Ni Steel

Understanding the relation between creep-fatigue fracture mechanisms and intergranular dislocation accommodation of a high chromium steel using nanoindentation characterization

Unveiling the Microstructure Evolution and the Short-Time Tensile Creep Behavior in the CuCrZr Alloy

Microstructure and Property Evolutions of a Novel Super304H Steel During High Temperature Creeping

Creep Behavior and Microstructure Evolution of Ni-based Alloy IN617 at 1000 °C

Precipitation Evolution in the Austenitic Heat-Resistant Steel HR3C upon Creep at 700 °C and 750 °C

High temperature creep behavior of a novel Cr18Ni9NbTiN austenitic stainless steel

Microstructural Evolution of X20CrMoV12.1 Steel Upon Short-term Creep Rupture Test

Effect of Long-Term Thermal Aging on Microstructure Evolution and Creep Deformation Behavior of a Novel 11Cr-3W-3Co Martensite Ferritic Steel

Evolution of Precipitated Phases during Creep of G115/Sanicro25 Dissimilar Steel Welded Joints

Microstructural evolution and the effect on strength of G115 steel after long-term creep at 923 K

Effect of Stress on Microstructural Evolution and Mechanical Properties of 12cr3w3co Steel During Aging and Short-Term Creep

Atomistic Study on High Temperature Creep of Nanocrystalline 316L Austenitic Stainless Steels

Microstructural Evolution of a Re-Containing 10% Cr-3Co-3W Steel during Creep at Elevated Temperature