Abstract:Optimization of the structural and working parameters for a cutting system are essential to improve the working performance and reduce the cutting energy consumption and mechanical damage of the vegetable harvester machinery. An asymmetric root-cutting system was developed to efficiently solve the problems of high cutting loss and energy consumption of mechanized harvesting of Chinese cabbage. Discrete element method (DEM) and microscopic observation were utilized to establish the simulation model of Chinese cabbage, and a delamination particle model was proposed in terms of contact interactions. The experimental methods of Plackett-Burman design (PBD), steepest ascent (SA), and Box Behnken design (BBD) were applied to determine significant factors from eight major influential factors and to optimize the structural and working parameters of the cutting system, and further validated experiments were performed according to the practical feasibility of the optimal combinations of parameters. Finally, the cutting mechanisms were revealed both at a macro and micro level by comparative analyses of the cutting process using EDEM simulation. On this basis, the designed root-cutting device was configured on the self-propelled Chinese cabbage harvester for experimental verification. Results showed that the four most impactful factors on maximum reaction force (MRF) of root-cutting were determined in the order of cutting pitch angle ( D ), cutter speed ( A ), walking speed ( E ), and cutter overlap amount ( B ), and most interactions between interactive factors had consequences for the cutting force change, except A and cutting position ( C ). The minimum value of MRF was 88.62 N when the cutter speed, cutter overlap amount, cutting pitch angle, and walking speed were 186.91 r min −1 , 17.87 mm, 12.26°, and 0.30 m s −1 , respectively. Results of the validated experiments indicated that the measured MRF was 93.41 N under the specified parameters of 187 r min −1 , 18 mm, 12°, and 0.3 m s −1 . This value was found to be comparable to the original value, within an acceptable percentage change of 5.41 %. These findings demonstrate the feasibility of optimizing the cutting system based on DEM. In comparison to the three most prevalent combinations of cutting disks, the cutting system utilizing one concave disk and one sawtooth disk could efficiently sever roots over shorter periods during the cutting process. The combined disks were arranged at an angle of 12° in the longitudinal direction. The forces of each layer of the particle structure inside the root were inconsistent during the root-cutting process. The internal bonding forces of the two-layer particle model played a role as a structural support of the parenchyma in the root epidermis, and the connecting epidermis between the inner and outer epidermis stand greater forces. The result of the field experiment showed that the average productivity of the Chinese cabbage harvester was 0.11 hm 2 h −1 , and the average qualified rate of root-cutting was 93.40 %, which demonstrated that the optimized root-cutting device efficiently fulfills the harvest requirements of high efficiency, and low cutting energy consumption and damage.

Parameter Combination Optimization of the Lateral Straw Clearing and Throwing Knife Based on Discrete Element Simulation

Optimization and Experiment of Straw Back-Throwing Device of No-Tillage Drill Using Multi-Objective QPSO Algorithm

OPTIMUM DESIGN FOR BREAKING DEVICE WITH DOUBLE ROLLER BASED EDEM

Simulation of Soil Cutting and Power Consumption Optimization of a Typical Rotary Tillage Soil Blade

DEVELOPMENT AND TEST OF CORN STRAW KNEADING AND CONVEYING DEVICE

Optimization of cutting position and mode for cabbage harvesting

Optimization Design and Experiment of Ear-Picking and Threshing Devices of Corn Plot Kernel Harvester

Optimisation and Finite Element Simulation of the Chopping Process for Chopper Sugarcane Harvesting

DESIGN AND EXPERIMENT OF THRESHING AND SEPARATING DEVICE OF CORN GRAIN HARVESTER / 玉米籽粒收获机脱粒分离装置设计与试验研究

Optimization of a Whole-Stalk Operating System after Sugarcane Base Cutting

Numerical simulation and field tests of minimum-tillage planter with straw smashing and strip laying based on EDEM software

Analysis and Test of Splitting Failure in the Cutting Process of Cabbage Root

Calibration and Validation of Simulation Parameters for Maize Straw Based on Discrete Element Method and Genetic Algorithm-Backpropagation

Tissue culture studies of blood vessel grafts. I. The cultivation in vitro of fresh normal adult aorta (dog, cat, rabbit, goat, monkey, and human).

Design and Experimental Study of a Bi-Directional Rotating Stubble-Cutting No-Tillage Planter

DISCRETE ELEMENT METHOD (EDEM) SIMULATION AND PARAMETER OPTIMIZATION: DESIGN AND TESTING OF A LOW-LOSS AND HIGH-EFFICIENCY CORN THRESHING DEVICE

DESIGN AND EXPERIMENT OF TRANSVERSE AXIAL FLOW CORN FLEXIBLE THRESHING DEVICE

Analysis of Multi-Objective Optimization of Machining Allowance Distribution and Parameters for Energy Saving Strategy

Numerical and Experimental Study on Optimization of Paddy Field Blade Used in Initial Mud-Cutting Process

Optimization and validation of root-cutting device for Chinese cabbage harvester based on discrete element method